Fix external start fail

components/esp32/Kconfig

@@ -775,6 +775,19 @@ menu "ESP32-specific"
             bool "Internal 8.5MHz oscillator, divided by 256 (~33kHz)"
     endchoice
 
+    config ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT
+        bool "Additional current for external 32kHz crystal"
+        depends on ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL
+        default "n"
+        help
+            Choose which additional current is used for rtc external crystal.
+
+            - With some 32kHz crystal configurations, the X32N and X32P pins may not
+              have enough drive strength to keep the crystal oscillating during deep sleep.
+              If this option is enabled, additional current from touchpad 9 is provided
+              internally to drive the 32kHz crystal. If this option is enabled, deep sleep current
+              is slightly higher (4-5uA) and the touchpad and ULP wakeup sources are not available.
+
     config ESP32_RTC_CLK_CAL_CYCLES
         int "Number of cycles for RTC_SLOW_CLK calibration"
         default 3000 if ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL

components/esp32/include/esp_sleep.h

@@ -95,6 +95,7 @@ esp_err_t esp_sleep_disable_wakeup_source(esp_sleep_source_t source);
  *       source is used.
  * @return
  *      - ESP_OK on success
+ *      - ESP_ERR_NOT_SUPPORTED if additional current by touch (CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT) is enabled.
  *      - ESP_ERR_INVALID_STATE if ULP co-processor is not enabled or if wakeup triggers conflict
  */
 esp_err_t esp_sleep_enable_ulp_wakeup();
@@ -121,6 +122,7 @@ esp_err_t esp_sleep_enable_timer_wakeup(uint64_t time_in_us);
  *
  * @return
  *      - ESP_OK on success
+ *      - ESP_ERR_NOT_SUPPORTED if additional current by touch (CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT) is enabled.
  *      - ESP_ERR_INVALID_STATE if wakeup triggers conflict
  */
 esp_err_t esp_sleep_enable_touchpad_wakeup();

components/esp32/sleep_modes.c

@@ -403,6 +403,9 @@ esp_err_t esp_sleep_disable_wakeup_source(esp_sleep_source_t source)
 
 esp_err_t esp_sleep_enable_ulp_wakeup()
 {
+#ifdef CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT
+    return ESP_ERR_NOT_SUPPORTED;
+#endif
 #ifdef CONFIG_ULP_COPROC_ENABLED
     if(s_config.wakeup_triggers & RTC_EXT0_TRIG_EN) {
         ESP_LOGE(TAG, "Conflicting wake-up trigger: ext0");
@@ -436,6 +439,9 @@ static void timer_wakeup_prepare()
 
 esp_err_t esp_sleep_enable_touchpad_wakeup()
 {
+#ifdef CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT
+    return ESP_ERR_NOT_SUPPORTED;
+#endif
     if (s_config.wakeup_triggers & (RTC_EXT0_TRIG_EN)) {
         ESP_LOGE(TAG, "Conflicting wake-up trigger: ext0");
         return ESP_ERR_INVALID_STATE;
@@ -695,6 +701,13 @@ static uint32_t get_power_down_flags()
     if (s_config.pd_options[ESP_PD_DOMAIN_XTAL] != ESP_PD_OPTION_ON) {
         pd_flags |= RTC_SLEEP_PD_XTAL;
     }
+
+    if ((s_config.wakeup_triggers & (RTC_TOUCH_TRIG_EN | RTC_ULP_TRIG_EN)) == 0) {
+    // If enabled EXT1 only and enable the additional current by touch, should be keep RTC_PERIPH power on.
+#if ((defined CONFIG_ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL) && (defined CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT))
+    pd_flags &= ~RTC_SLEEP_PD_RTC_PERIPH;
+#endif
+    }
     return pd_flags;
 }
 

components/soc/esp32/rtc_clk.c

@@ -85,7 +85,7 @@
 /* Core voltage needs to be increased in two cases:
  * 1. running at 240 MHz
  * 2. running with 80MHz Flash frequency
- * 
+ *
  * There is a record in efuse which indicates the proper voltage for these two cases.
  */
 #define RTC_CNTL_DBIAS_HP_VOLT         (RTC_CNTL_DBIAS_1V25 - (REG_GET_FIELD(EFUSE_BLK0_RDATA5_REG, EFUSE_RD_VOL_LEVEL_HP_INV)))
@@ -116,7 +116,7 @@ static void rtc_clk_32k_enable_common(int dac, int dres, int dbias)
 {
     CLEAR_PERI_REG_MASK(RTC_IO_XTAL_32K_PAD_REG,
                         RTC_IO_X32P_RDE | RTC_IO_X32P_RUE | RTC_IO_X32N_RUE |
-                        RTC_IO_X32N_RDE | RTC_IO_X32N_MUX_SEL | RTC_IO_X32P_MUX_SEL);
+                        RTC_IO_X32N_RDE | RTC_IO_X32N_FUN_IE | RTC_IO_X32P_FUN_IE);
     SET_PERI_REG_MASK(RTC_IO_XTAL_32K_PAD_REG, RTC_IO_X32N_MUX_SEL | RTC_IO_X32P_MUX_SEL);
     /* Set the parameters of xtal
         dac --> current
@@ -127,7 +127,8 @@ static void rtc_clk_32k_enable_common(int dac, int dres, int dbias)
     REG_SET_FIELD(RTC_IO_XTAL_32K_PAD_REG, RTC_IO_DRES_XTAL_32K, dres);
     REG_SET_FIELD(RTC_IO_XTAL_32K_PAD_REG, RTC_IO_DBIAS_XTAL_32K, dbias);
 
-    /* TOUCH sensor can provide additional current to external XTAL. 
+#ifdef CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT
+    /* TOUCH sensor can provide additional current to external XTAL.
        In some case, X32N and X32P PAD don't have enough drive capability to start XTAL */
     SET_PERI_REG_MASK(RTC_IO_TOUCH_CFG_REG, RTC_IO_TOUCH_XPD_BIAS_M);
     /* Tie PAD Touch8 to VDD
@@ -140,6 +141,7 @@ static void rtc_clk_32k_enable_common(int dac, int dres, int dbias)
        So the Touch DAC start to drive some current from VDD to TOUCH8(which is also XTAL-N)
      */
     SET_PERI_REG_MASK(RTC_IO_TOUCH_PAD9_REG, RTC_IO_TOUCH_PAD9_XPD_M);
+#endif // CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT
     /* Power up external xtal */
     SET_PERI_REG_MASK(RTC_IO_XTAL_32K_PAD_REG, RTC_IO_XPD_XTAL_32K_M);
 }
@@ -150,9 +152,13 @@ void rtc_clk_32k_enable(bool enable)
         rtc_clk_32k_enable_common(XTAL_32K_DAC_VAL, XTAL_32K_DRES_VAL, XTAL_32K_DBIAS_VAL);
     } else {
         /* Disable X32N and X32P pad drive external xtal */
-        CLEAR_PERI_REG_MASK(RTC_IO_XTAL_32K_PAD_REG, RTC_IO_XPD_XTAL_32K);
+        CLEAR_PERI_REG_MASK(RTC_IO_XTAL_32K_PAD_REG, RTC_IO_XPD_XTAL_32K_M);
+        CLEAR_PERI_REG_MASK(RTC_IO_XTAL_32K_PAD_REG, RTC_IO_X32N_MUX_SEL | RTC_IO_X32P_MUX_SEL);
+
+#ifdef CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT
         /* Power down TOUCH */
         CLEAR_PERI_REG_MASK(RTC_IO_TOUCH_PAD9_REG, RTC_IO_TOUCH_PAD9_XPD_M);
+#endif // CONFIG_ESP32_RTC_EXTERNAL_CRYSTAL_ADDITIONAL_CURRENT
     }
 }