| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194 |
- menu "Hardware Drivers Config"
- menu "Onboard Peripheral Drivers"
- config BSP_USING_ETHERCAT_EOE
- bool "Enable EtherCAT EOE example"
- select BSP_USING_ETH
- default n
- if BSP_USING_ETHERCAT_EOE
- config RT_LWIP_IPADDR
- string "set static ip address for eoe slaver"
- default "192.168.10.100"
- config RT_LWIP_GWADDR
- string "set static gateway address for eoe slaver"
- default "192.168.10.1"
- config RT_LWIP_MSKADDR
- string "set static mask address for eoe slaver"
- default "255.255.255.0"
- endif
- endmenu
- menu "On-chip Peripheral Drivers"
- rsource "../../libraries/HAL_Drivers/drivers/Kconfig"
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- select RT_USING_SERIAL_V2
- if BSP_USING_UART
- menuconfig BSP_USING_UART0
- bool "Enable UART0"
- default n
- if BSP_USING_UART0
- config BSP_UART0_RX_USING_DMA
- bool "Enable UART0 RX DMA"
- depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
- default n
- config BSP_UART0_TX_USING_DMA
- bool "Enable UART0 TX DMA"
- depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
- default n
- config BSP_UART0_RX_BUFSIZE
- int "Set UART0 RX buffer size"
- range 64 65535
- depends on RT_USING_SERIAL_V2
- default 256
- config BSP_UART0_TX_BUFSIZE
- int "Set UART0 TX buffer size"
- range 0 65535
- depends on RT_USING_SERIAL_V2
- default 0
- endif
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- menuconfig BSP_USING_CANFD
- bool "Enable CANFD"
- default n
- select RT_USING_CAN
- select RT_CAN_USING_CANFD
- if BSP_USING_CANFD
- config BSP_USING_CAN0
- bool "Enable CANFD0"
- default n
- endif
- menuconfig BSP_USING_I2C
- bool "Enable I2C BUS"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C
- config BSP_USING_HW_I2C
- bool "Enable Hardware I2C BUS"
- default n
- if BSP_USING_HW_I2C
- config BSP_USING_HW_I2C0
- bool "Enable Hardware I2C0 BUS"
- default n
- endif
- if BSP_USING_HW_I2C
- config BSP_USING_HW_I2C1
- bool "Enable Hardware I2C1 BUS"
- default n
- endif
- if !BSP_USING_HW_I2C
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default y
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- hex "i2c1 scl pin number"
- range 0x0000 0x0B0F
- default 0x0B03
- config BSP_I2C1_SDA_PIN
- hex "I2C1 sda pin number"
- range 0x0000 0x0B0F
- default 0x050E
- endif
- endif
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI0
- bool "Enable SPI0 BUS"
- default n
- config BSP_USING_SPI1
- bool "Enable SPI1 BUS"
- default n
- config BSP_USING_SPI2
- bool "Enable SPI2 BUS"
- default n
- endif
- menuconfig BSP_USING_TIM
- bool "Enable timer"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TIM
- config BSP_USING_TIM0
- bool "Enable TIM0"
- default n
- config BSP_USING_TIM1
- bool "Enable TIM1"
- default n
- endif
- config BSP_USING_ETH
- bool "Enable Ethernet"
- select RT_USING_SAL
- select RT_USING_LWIP
- select RT_USING_NETDEV
- default n
- endmenu
-
- menu "Board extended module Drivers"
- menuconfig BSP_USING_RW007
- bool "Enable RW007"
- default n
- select PKG_USING_RW007
- select BSP_USING_SPI
- select BSP_USING_SPI2
- select RT_USING_MEMPOOL
- select RW007_NOT_USE_EXAMPLE_DRIVERS
- if BSP_USING_RW007
- config RA_RW007_SPI_BUS_NAME
- string "RW007 BUS NAME"
- default "spi2"
- config RA_RW007_CS_PIN
- hex "(HEX)CS pin index"
- default 0x1207
- config RA_RW007_BOOT0_PIN
- hex "(HEX)BOOT0 pin index (same as spi clk pin)"
- default 0x1204
- config RA_RW007_BOOT1_PIN
- hex "(HEX)BOOT1 pin index (same as spi cs pin)"
- default 0x1207
- config RA_RW007_INT_BUSY_PIN
- hex "(HEX)INT/BUSY pin index"
- default 0x1102
- config RA_RW007_RST_PIN
- hex "(HEX)RESET pin index"
- default 0x1706
- endif
- endmenu
- endmenu
|
