rt-thread/bsp/nrf5x/nrf5340/board/Kconfig

menu "Hardware Drivers Config"

config SOC_NRF5340
    bool
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

config SOC_NORDIC
    bool
    default y

choice
    prompt "Select BSP board "
    default BSP_BOARD_PCA_10095

    config BSP_BOARD_PCA_10095
        select BSP_USING_UART
        select BSP_USING_UART0
        bool "NRF5340 pca10095 "

    config BSP_BOARD_ARDUINO_NANO_33_BLE
        bool "Arduino Nano 33 BLE (Sense)"
endchoice

menu "Onboard Peripheral Drivers"
    config BSP_USING_JLINK_TO_USART
        bool "Enable JLINK TO USART (uart0|RX_PIN:8|TX_PIN:6)"
        default y
        depends on BSP_BOARD_PCA_10095

    config RT_BSP_LED_PIN
        int
        default 28 if BSP_BOARD_PCA_10095
        default 16 if BSP_BOARD_ARDUINO_NANO_33_BLE
        depends on BSP_USING_GPIO


    menuconfig BSP_USING_QSPI_FLASH
        select PKG_USING_FAL
        bool "Enable QSPI FLASH(MX25R64 8MB)"
        default n
        depends on BSP_BOARD_PCA_10095

        if BSP_USING_QSPI_FLASH
            config NRFX_QSPI_ENABLED
            int
            default 1
            config BSP_QSPI_SCK_PIN
                int "QSPI SCK pin number"
                range 0 31
                default 17
            config BSP_QSPI_CSN_PIN
                int "QSPI CSN pin number"
                range 0 31
                default 18
            config BSP_QSPI_IO0_PIN
                int "QSPI IO0 pin number"
                range 0 31
                default 13
            config BSP_QSPI_IO1_PIN
                int "QSPI IO1 pin number"
                range 0 31
                default 14
            config BSP_QSPI_IO2_PIN
                int "QSPI IO2 pin number"
                range 0 31
                default 15
            config BSP_QSPI_IO3_PIN
                int "QSPI IO3 pin number"
                range 0 31
                default 16
            config QSPI_FLASH_SIZE_KB
                int "QSPI FLASH SIZE, DEFAULT size 8192 KB"
                default 8192
        endif
endmenu


menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    config BSP_USING_UART
        bool "Enable UART"
        default n
        select RT_USING_SERIAL
        if BSP_USING_UART
        choice
        prompt "UART or UARTE"
        default NRFX_USING_UARTE
        help
            Select the UART or UARTE
        config NRFX_USING_UART
            bool "UART"

        config NRFX_USING_UARTE
            bool "UARTE"
        endchoice
        endif
        if BSP_USING_UART&&NRFX_USING_UART
            config BSP_USING_UART0
                bool "Enable UART0"
                default y
                if BSP_USING_UART0
                    config BSP_UART0_RX_PIN
                        int "uart0 rx pin number"
                        range 0 64
                        default 8 if BSP_BOARD_PCA_10095
                        default 42 if BSP_BOARD_ARDUINO_NANO_33_BLE
                    config BSP_UART0_TX_PIN
                        int "uart0 tx pin number"
                        range 0 64
                        default 6 if BSP_BOARD_PCA_10095
                        default 35 if BSP_BOARD_ARDUINO_NANO_33_BLE
                endif
        endif
        if BSP_USING_UART&&NRFX_USING_UARTE
            config NRFX_UARTE_ENABLED
            int
            default 1

            config BSP_USING_UART0
                bool "Enable UARTE0"
                default n
                if BSP_USING_UART0
                    config NRFX_UARTE0_ENABLED
                    int
                    default 1
                    config BSP_UART0_RX_PIN
                        int "uarte0 rx pin number"
                        range 0 64
                        default 8
                    config BSP_UART0_TX_PIN
                        int "uarte0 tx pin number"
                        range 0 64
                        default 6
                endif
            config BSP_USING_UART1
                bool "Enable UARTE1"
                default n
                if BSP_USING_UART1
                    config NRFX_UARTE1_ENABLED
                    int
                    default 1
                    config BSP_UART1_RX_PIN
                        int "uarte1 rx pin number"
                        range 0 64
                        default 7
                    config BSP_UART1_TX_PIN
                        int "uarte1 tx pin number"
                        range 0 64
                        default 5
                endif
             config BSP_USING_UART2
                bool "Enable UARTE2"
                default n
                if BSP_USING_UART2
                    config NRFX_UARTE2_ENABLED
                    int
                    default 1
                    config BSP_UART2_RX_PIN
                        int "uarte2 rx pin number"
                        range 0 64
                        default 7
                    config BSP_UART2_TX_PIN
                        int "uarte2 tx pin number"
                        range 0 64
                        default 5
                endif
            config BSP_USING_UART3
                bool "Enable UARTE3"
                default n
                if BSP_USING_UART3
                    config NRFX_UARTE3_ENABLED
                    int
                    default 1
                    config BSP_UART3_RX_PIN
                        int "uarte3 rx pin number"
                        range 0 64
                        default 7
                    config BSP_UART3_TX_PIN
                        int "uarte3 tx pin number"
                        range 0 64
                        default 5
                endif
        endif

    config BSP_USING_SAADC
        bool "Enable ADC"
        select RT_USING_ADC
        default n

    config BSP_USING_IPC
        bool "Enable IPC"
        select RT_USING_IPC
        default n

    menuconfig BSP_USING_I2C
        bool "Enable I2C"
        select RT_USING_I2C
        default n
        if BSP_USING_I2C
            config BSP_USING_I2C0
                bool "Enable I2C0 bus"
                default y
            if BSP_USING_I2C0
                config BSP_I2C0_SCL_PIN
                    int "i2c0 scl pin number"
                    range 0 31
                    default 27
                config BSP_I2C0_SDA_PIN
                    int "I2C0 sda pin number"
                    range 0 31
                    default 26
            endif
            config BSP_USING_I2C1
                bool "Enable I2C1 bus"
                default n
            if BSP_USING_I2C1
                config BSP_I2C1_SCL_PIN
                    int "i2c1 scl pin number"
                    range 0 31
                    default 26
                config BSP_I2C1_SDA_PIN
                    int "I2C1 sda pin number"
                    range 0 31
                    default 25
            endif
            config BSP_USING_I2C2
                bool "Enable I2C2 bus"
                default n
            if BSP_USING_I2C2
                config BSP_I2C2_SCL_PIN
                    int "i2c2 scl pin number"
                    range 0 31
                    default 3
                config BSP_I2C2_SDA_PIN
                    int "I2C2 sda pin number"
                    range 0 31
                    default 2
            endif
            config BSP_USING_I2C3
                bool "Enable I2C3 bus"
                default n
            if BSP_USING_I2C3
                config BSP_I2C3_SCL_PIN
                    int "i2c3 scl pin number"
                    range 0 31
                    default 5
                config BSP_I2C3_SDA_PIN
                    int "I2C3 sda pin number"
                    range 0 31
                    default 4
            endif
        endif

   menuconfig BSP_USING_SPI
        bool "Enable SPI"
        select RT_USING_SPI
        default n

        if BSP_USING_SPI
            config BSP_USING_SPI0
                bool "Enable SPI0 bus"
                default y
            if BSP_USING_SPI0
                config NRFX_SPIM0_ENABLED
                    int "Enable SPI0 instance"
                    default 1
                config BSP_SPI0_SCK_PIN
                    int "SPI0 sck pin number set"
                    range 0 47
                    default 28
                config BSP_SPI0_MOSI_PIN
                    int "SPI0 mosi pin number set"
                    range 0 47
                    default 29
                config BSP_SPI0_MISO_PIN
                    int "SPI0 miso pin number set"
                    range 0 47
                    default 30
                config BSP_SPI0_SS_PIN
                    int "SPI0 ss pin number set"
                    range 0 47
                    default 31
            endif

            config BSP_USING_SPI1
                bool "Enable SPI1 bus"
                default n
            if BSP_USING_SPI1
                config BSP_SPI1_SCK_PIN
                    int "SPI1 sck pin number set"
                    range 0 47
                    default 28
                config BSP_SPI1_MOSI_PIN
                    int "SPI1 mosi pin number set"
                    range 0 47
                    default 29
                config BSP_SPI1_MISO_PIN
                    int "SPI1 miso pin number set"
                    range 0 47
                    default 30
                config BSP_SPI1_SS_PIN
                    int "SPI1 ss pin number set"
                    range 0 47
                    default 31
            endif

            config BSP_USING_SPI2
                bool "Enable SPI2 bus"
                default n
            if BSP_USING_SPI2
                config BSP_SPI2_SCK_PIN
                    int "SPI2 sck pin number set"
                    range 0 47
                    default 28
                config BSP_SPI2_MOSI_PIN
                    int "SPI2 mosi pin number set"
                    range 0 47
                    default 29
                config BSP_SPI2_MISO_PIN
                    int "SPI2 miso pin number set"
                    range 0 47
                    default 30
                config BSP_SPI2_SS_PIN
                    int "SPI2 ss pin number set"
                    range 0 47
                    default 31
            endif
            config BSP_USING_SPI3
                bool "Enable SPI3 bus"
                default n
            if BSP_USING_SPI3
                config BSP_SPI3_SCK_PIN
                    int "SPI3 sck pin number set"
                    range 0 47
                    default 28
                config BSP_SPI3_MOSI_PIN
                    int "SPI3 mosi pin number set"
                    range 0 47
                    default 29
                config BSP_SPI2_MISO_PIN
                    int "SPI3 miso pin number set"
                    range 0 47
                    default 30
                config BSP_SPI3_SS_PIN
                    int "SPI3 ss pin number set"
                    range 0 47
                    default 31
            endif
            config BSP_USING_SPI4
                bool "Enable SPI4 bus"
                default n
            if BSP_USING_SPI4
                config BSP_SPI4_SCK_PIN
                    int "SPI4 sck pin number set"
                    range 0 47
                    default 8
                config BSP_SPI4_MOSI_PIN
                    int "SPI4 mosi pin number set"
                    range 0 47
                    default 9
                config BSP_SPI4_MISO_PIN
                    int "SPI4 miso pin number set"
                    range 0 47
                    default 10
                config BSP_SPI4_SS_PIN
                    int "SPI4 ss pin number set"
                    range 0 47
                    default 11
            endif
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        select RT_USING_PWM
        default n
        if BSP_USING_PWM
            config BSP_USING_PWM0
                bool "Enable PWM0 bus"
                default y
            if BSP_USING_PWM0
                config BSP_USING_PWM0_CH0
                    int "PWM0 channel 0 pin number set"
                    range 0 47
                    default 28
                config BSP_USING_PWM0_CH1
                    int "PWM0 channel 1 pin number set"
                    range 0 47
                    default 29
                config BSP_USING_PWM0_CH2
                    int "PWM0 channel 2 pin number set"
                    range 0 47
                    default 30
                config BSP_USING_PWM0_CH3
                    int "PWM0 channel 3 pin number set"
                    range 0 47
                    default 31
            endif
            config BSP_USING_PWM1
                bool "Enable PWM1 bus"
                default n
            if BSP_USING_PWM1
                config NRFX_PWM1_ENABLED
                int
                default 1
                config BSP_USING_PWM1_CH0
                    int "PWM1 channel 0 pin number set"
                    range 0 47
                    default 13
                config BSP_USING_PWM1_CH1
                    int "PWM1 channel 1 pin number set"
                    range 0 47
                    default 14
                config BSP_USING_PWM1_CH2
                    int "PWM1 channel 2 pin number set"
                    range 0 47
                    default 15
                config BSP_USING_PWM1_CH3
                    int "PWM1 channel 3 pin number set"
                    range 0 47
                    default 16
            endif
            config BSP_USING_PWM2
                bool "Enable PWM2 bus"
                default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH0
                    int "PWM2 channel 0 pin number set"
                    range 0 47
                    default 13
                config BSP_USING_PWM2_CH1
                    int "PWM2 channel 1 pin number set"
                    range 0 47
                    default 14
                config BSP_USING_PWM2_CH2
                    int "PWM2 channel 2 pin number set"
                    range 0 47
                    default 15
                config BSP_USING_PWM2_CH3
                    int "PWM2 channel 3 pin number set"
                    range 0 47
                    default 16
            endif
            config BSP_USING_PWM3
                bool "Enable PWM3 bus"
                default n
            if BSP_USING_PWM3
                config BSP_USING_PWM3_CH0
                    int "PWM3 channel 0 pin number set"
                    range 0 47
                    default 13
                config BSP_USING_PWM3_CH1
                    int "PWM3 channel 1 pin number set"
                    range 0 47
                    default 14
                config BSP_USING_PWM3_CH2
                    int "PWM3 channel 2 pin number set"
                    range 0 47
                    default 15
                config BSP_USING_PWM3_CH3
                    int "PWM3 channel 3 pin number set"
                    range 0 47
                    default 16
            endif
        endif

    config BSP_USING_WDT
        bool "Enable WDT"
        select RT_USING_WDT
        default n

    menuconfig BSP_USING_ONCHIP_RTC
    bool "Enable RTC"
    select RT_USING_RTC
    default n


    config BSP_USING_ON_CHIP_FLASH
        select PKG_USING_FAL
        bool "Enable on-chip FLASH"
        default n

    menu "MCU flash config"

        config MCU_FLASH_START_ADDRESS
            hex "MCU FLASH START ADDRESS"
            default 0x00000000

        config MCU_FLASH_SIZE_KB
            int "MCU FLASH SIZE, MAX size 1024 KB"
            default 1024

        config MCU_SRAM_START_ADDRESS
            hex "MCU RAM START ADDRESS"
            default 0x20000000

        config MCU_SRAM_SIZE_KB
            int "MCU RAM SIZE"
            default 256

        config MCU_FLASH_PAGE_SIZE
            hex "MCU FLASH PAGE SIZE, please not change,nrfx default is 0x1000"
            default 0x1000
    endmenu

    config BSP_USING_TIM
        bool "Enable TIMER"
        select RT_USING_HWTIMER
        default n
        if BSP_USING_TIM
            config NRFX_TIMER_ENABLED
            int
            default 1
            config BSP_USING_TIM1
                bool "Enable TIMER1"
                default n
            if BSP_USING_TIM1
                config NRFX_TIMER1_ENABLED
                int
                default 1
            endif
            config BSP_USING_TIM2
                bool "Enable TIMER2"
                default n
            if BSP_USING_TIM2
                config NRFX_TIMER2_ENABLED
                int
                default 1
            endif
        endif


    if PKG_USING_TINYUSB
        config NRFX_POWER_ENABLED
        int
        default 1
    endif

endmenu

choice
prompt "BLE STACK"
default BLE_STACK_USING_NULL
help
    Select the ble stack

config BLE_STACK_USING_NULL
    bool "not use the ble stack"

config  BSP_USING_SOFTDEVICE
    select PKG_USING_NRF5X_SDK
    bool "Nordic softdevice(perpheral)"

config BSP_USING_NIMBLE
    select PKG_USING_NIMBLE
    select PKG_NIMBLE_BSP_NRF52840
    bool "use nimble stack(iot)"
endchoice

if SOC_NORDIC
    config NRFX_CLOCK_ENABLED
    int
    default 1
    config    NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY
    int
    default 7
    config NRFX_CLOCK_CONFIG_LF_SRC
    int
    default 1
endif

if BSP_USING_UART
    config NRFX_USING_UART
    bool
    default y

    config NRFX_UART_ENABLED
    int
    default 1
if BSP_USING_UART0
    config NRFX_UART0_ENABLED
    int
    default 1
endif

if NRFX_USING_UART
    config NRFX_UART_ENABLED
    int
    default 1
endif

if NRFX_USING_UARTE
    config NRFX_UARTE0_ENABLED
    int
    default 1
endif


endif

if BSP_USING_GPIO
    config NRFX_GPIOTE_ENABLED
    int
    default 1
endif

if BSP_USING_SAADC
    config NRFX_SAADC_ENABLED
    int
    default 1
endif

if BSP_USING_I2C
    config NRFX_TWIM_ENABLED
    int
    default 1
    if BSP_USING_I2C0
        config NRFX_TWIM0_ENABLED
        int
        default 1
    endif

    if BSP_USING_I2C1
        config NRFX_TWIM1_ENABLED
        int
        default 1
    endif

    if BSP_USING_I2C2
        config NRFX_TWIM2_ENABLED
        int
        default 1
    endif

    if BSP_USING_I2C3
        config NRFX_TWIM3_ENABLED
        int
        default 1
    endif
endif

if BSP_USING_SPI
    config NRFX_SPIM_ENABLED
    int
    default 1

    if BSP_USING_SPI0
        config NRFX_SPIM0_ENABLED
        int
        default 1
    endif

    if BSP_USING_SPI1
        config NRFX_SPIM1_ENABLED
        int
        default 1
    endif

    if BSP_USING_SPI2
        config NRFX_SPIM2_ENABLED
        int
        default 1
    endif

    if BSP_USING_SPI3
        config NRFX_SPIM3_ENABLED
        int
        default 1
    endif

    if BSP_USING_SPI4
        config NRFX_SPIM4_ENABLED
        int
        default 1
    endif
endif

if BSP_USING_PWM
    config NRFX_PWM_ENABLED
    int
    default 1
    if BSP_USING_PWM0
        config NRFX_PWM0_ENABLED
        int
        default 1
    endif
    if BSP_USING_PWM1
    config NRFX_PWM1_ENABLED
    int
    default 1
    endif
    if BSP_USING_PWM2
        config NRFX_PWM2_ENABLED
        int
        default 1
    endif
    if BSP_USING_PWM3
        config NRFX_PWM3_ENABLED
        int
        default 1
    endif

endif

if BSP_USING_WDT
    config NRFX_WDT_ENABLED
    int
    default 1
    config NRFX_WDT0_ENABLED
    int
    default 1
    config NRFX_WDT_CONFIG_NO_IRQ
    int
    default 1
endif

if BSP_USING_ONCHIP_RTC
    config NRFX_CLOCK_ENABLED
    int
    default 1
    config NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY
    int
    default 7
    config NRFX_RTC_ENABLED
    int
    default 1
    config NRFX_RTC1_ENABLED
    int
    default 1
    config NRFX_RTC2_ENABLED
    int
    default 0
    config RTC_INSTANCE_ID
    int
    default 1
endif



endmenu