!248 add air780e bsp

Merge pull request !248 from Kirin/master

bsp/air780e/inc/RTE_Device.h

@@ -0,0 +1,350 @@
+#ifndef __RTE_DEVICE_H
+#define __RTE_DEVICE_H
+
+#include "ec618.h"
+
+/*  Peripheral IO Mode Select, Must Configure First !!!
+    Note, when receiver works in DMA_MODE, interrupt is also enabled to transfer tailing bytes.
+*/
+
+#define POLLING_MODE            0x1
+#define DMA_MODE                0x2
+#define IRQ_MODE                0x3
+#define UNILOG_MODE             0x4
+
+#define RTE_UART0_TX_IO_MODE    UNILOG_MODE
+#define RTE_UART0_RX_IO_MODE    IRQ_MODE
+#define USART0_RX_TRIG_LVL      (30)
+
+#define RTE_UART1_TX_IO_MODE    DMA_MODE
+#define RTE_UART1_RX_IO_MODE    DMA_MODE
+
+#define RTE_UART2_TX_IO_MODE    POLLING_MODE
+#define RTE_UART2_RX_IO_MODE    DMA_MODE
+
+#define RTE_SPI0_IO_MODE        POLLING_MODE
+
+#define RTE_SPI1_IO_MODE        POLLING_MODE
+
+#define RTE_I2C0_IO_MODE        POLLING_MODE
+#define RTE_I2C1_IO_MODE        POLLING_MODE
+
+
+// I2C0 (Inter-integrated Circuit Interface) [Driver_I2C0]
+// Configuration settings for Driver_I2C0 in component ::Drivers:I2C
+#define RTE_I2C0                        1
+
+// { PAD_PIN28},  // 0 : gpio13 / 2 : I2C0 SCL
+// { PAD_PIN27},  // 0 : gpio12 / 2 : I2C0 SDA
+#define RTE_I2C0_SCL_BIT                28			// AUDIO use 28
+#define RTE_I2C0_SCL_FUNC               PAD_MUX_ALT2
+
+#define RTE_I2C0_SDA_BIT                27			// AUDIO use 27
+#define RTE_I2C0_SDA_FUNC               PAD_MUX_ALT2
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C0_DMA_TX_EN              0
+#define RTE_I2C0_DMA_TX_REQID           DMA_REQUEST_I2C0_TX
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C0_DMA_RX_EN              0
+#define RTE_I2C0_DMA_RX_REQID           DMA_REQUEST_I2C0_RX
+
+// I2C1 (Inter-integrated Circuit Interface) [Driver_I2C1]
+// Configuration settings for Driver_I2C1 in component ::Drivers:I2C
+#define RTE_I2C1                        1
+
+// { PAD_PIN20},  // 0 : gpio5  / 2 : I2C1 SCL
+// { PAD_PIN19},  // 0 : gpio4  / 2 : I2C1 SDA
+#define RTE_I2C1_SCL_BIT                20
+#define RTE_I2C1_SCL_FUNC               PAD_MUX_ALT2
+
+#define RTE_I2C1_SDA_BIT                19
+#define RTE_I2C1_SDA_FUNC               PAD_MUX_ALT2
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C1_DMA_TX_EN              1
+#define RTE_I2C1_DMA_TX_REQID           DMA_REQUEST_I2C1_TX
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C1_DMA_RX_EN              1
+#define RTE_I2C1_DMA_RX_REQID           DMA_REQUEST_I2C1_RX
+
+
+// UART0 (Universal asynchronous receiver transmitter) [Driver_USART0]
+// Configuration settings for Driver_USART0 in component ::Drivers:USART
+#define RTE_UART0_CTS_PIN_EN            0
+#define RTE_UART0_RTS_PIN_EN            0
+
+// { PAD_PIN27},  // 0 : gpio12 / 3 : UART0 RTSn
+// { PAD_PIN28},  // 0 : gpio13 / 3 : UART0 CTSn
+// { PAD_PIN29},  // 0 : gpio14 / 3 : UART0 RXD
+// { PAD_PIN30},  // 0 : gpio15 / 3 : UART0 TXD
+#define RTE_UART0_RTS_BIT               27
+#define RTE_UART0_RTS_FUNC              PAD_MUX_ALT3
+
+#define RTE_UART0_CTS_BIT               28
+#define RTE_UART0_CTS_FUNC              PAD_MUX_ALT3
+
+#define RTE_UART0_RX_BIT                29
+#define RTE_UART0_RX_FUNC               PAD_MUX_ALT3
+
+#define RTE_UART0_TX_BIT                30
+#define RTE_UART0_TX_FUNC               PAD_MUX_ALT3
+
+// DMA
+//  Tx
+//    Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART0_DMA_TX_REQID          DMA_REQUEST_USART0_TX
+//  Rx
+//    Channel    <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART0_DMA_RX_REQID          DMA_REQUEST_USART0_RX
+
+// UART1 (Universal asynchronous receiver transmitter) [Driver_USART1]
+// Configuration settings for Driver_USART1 in component ::Drivers:USART
+#define RTE_UART1_CTS_PIN_EN            1
+#define RTE_UART1_RTS_PIN_EN            1
+
+// { PAD_PIN31},  // 0 : gpio16  / 1 : UART1 RTS
+// { PAD_PIN32},  // 0 : gpio17  / 1 : UART1 CTS
+// { PAD_PIN33},  // 0 : gpio18  / 1 : UART1 RXD
+// { PAD_PIN34},  // 0 : gpio19  / 1 : UART1 TXD
+#define RTE_UART1_RTS_BIT               31
+#define RTE_UART1_RTS_FUNC              PAD_MUX_ALT1
+
+#define RTE_UART1_CTS_BIT               32
+#define RTE_UART1_CTS_FUNC              PAD_MUX_ALT1
+
+#define RTE_UART1_RX_BIT                33
+#define RTE_UART1_RX_FUNC               PAD_MUX_ALT1
+
+#define RTE_UART1_TX_BIT                34
+#define RTE_UART1_TX_FUNC               PAD_MUX_ALT1
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART1_DMA_TX_REQID          DMA_REQUEST_USART1_TX
+//   Rx
+//     Channel    <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART1_DMA_RX_REQID          DMA_REQUEST_USART1_RX
+
+// UART2 (Universal asynchronous receiver transmitter) [Driver_USART2]
+// Configuration settings for Driver_USART2 in component ::Drivers:USART
+#define RTE_UART2_CTS_PIN_EN            0
+#define RTE_UART2_RTS_PIN_EN            0
+
+// { PAD_PIN25},  // 0 : gpio10 / 3 : UART2 RXD
+// { PAD_PIN26},  // 0 : gpio11 / 3 : UART2 TXD
+#define RTE_UART2_RX_BIT                25
+#define RTE_UART2_RX_FUNC               PAD_MUX_ALT3
+
+#define RTE_UART2_TX_BIT                26
+#define RTE_UART2_TX_FUNC               PAD_MUX_ALT3
+
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART2_DMA_TX_REQID          DMA_REQUEST_USART2_TX
+//   Rx
+//     Channel    <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART2_DMA_RX_REQID          DMA_REQUEST_USART2_RX
+
+// SPI0 (Serial Peripheral Interface) [Driver_SPI0]
+// Configuration settings for Driver_SPI0 in component ::Drivers:SPI
+#define RTE_SPI0                        1
+
+// { PAD_PIN21},  // 0 : gpio16 / 1 : UART1 RTS / 2 : SPI0 SSn
+// { PAD_PIN22},  // 0 : gpio11 / 1 : UART1 CTS / 2 : SPI0 MOSI
+// { PAD_PIN23},  // 0 : gpio14 / 1 : UART1 RXD / 2 : SPI0 MISO
+// { PAD_PIN24},  // 0 : gpio15 / 1 : UART1 TXD / 2 : SPI0 SCLK
+#define RTE_SPI0_SSN_BIT                21
+#define RTE_SPI0_SSN_FUNC               PAD_MUX_ALT2
+
+#define RTE_SPI0_MOSI_BIT               22
+#define RTE_SPI0_MOSI_FUNC              PAD_MUX_ALT2
+
+#define RTE_SPI0_MISO_BIT               23
+#define RTE_SPI0_MISO_FUNC              PAD_MUX_ALT2
+
+#define RTE_SPI0_SCLK_BIT               24
+#define RTE_SPI0_SCLK_FUNC              PAD_MUX_ALT2
+
+#define RTE_SPI0_SSN_GPIO_INSTANCE      1
+#define RTE_SPI0_SSN_GPIO_INDEX         0
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI0_DMA_TX_REQID           DMA_REQUEST_SPI0_TX
+
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI0_DMA_RX_REQID           DMA_REQUEST_SPI0_RX
+
+// SPI1 (Serial Peripheral Interface) [Driver_SPI1]
+// Configuration settings for Driver_SPI1 in component ::Drivers:SPI
+#define RTE_SPI1                        1
+
+// { PAD_PIN13},  // 0 : gpio2 / 1 : UART0 RTSn / 3 : SPI1 SSn
+// { PAD_PIN14},  // 0 : gpio3 / 1 : UART0 CTSn / 3 : SPI1 MOSI
+// { PAD_PIN15},  // 0 : gpio4 / 1 : UART0 RXD  / 3 : SPI1 MISO
+// { PAD_PIN16},  // 0 : gpio5 / 1 : UART0 TXD  / 3 : SPI1 SCLK
+#define RTE_SPI1_SSN_BIT                13
+#define RTE_SPI1_SSN_FUNC               PAD_MUX_ALT3
+
+#define RTE_SPI1_MOSI_BIT               14
+#define RTE_SPI1_MOSI_FUNC              PAD_MUX_ALT3
+
+#define RTE_SPI1_MISO_BIT               15
+#define RTE_SPI1_MISO_FUNC              PAD_MUX_ALT3
+
+#define RTE_SPI1_SCLK_BIT               16
+#define RTE_SPI1_SCLK_FUNC              PAD_MUX_ALT3
+
+#define RTE_SPI1_SSN_GPIO_INSTANCE      0
+#define RTE_SPI1_SSN_GPIO_INDEX         2
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI1_DMA_TX_REQID           DMA_REQUEST_SPI1_TX
+
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI1_DMA_RX_REQID           DMA_REQUEST_SPI1_RX
+
+
+// PWM0 Controller [Driver_PWM0]
+// Configuration settings for Driver_PWM0 in component ::Drivers:PWM
+#define RTE_PWM                         1
+
+#define EFUSE_INIT_MODE POLLING_MODE
+#define L2CTLS_INIT_MODE POLLING_MODE
+
+#define FLASH_BARE_RW_MODE 1
+
+
+
+
+
+#define RTE_UART0                       1
+#define RTE_UART1                       1
+#define RTE_UART2                       1
+/* to enable external thermal */
+#define EXTERNAL_NTC_EXIST              0
+
+
+#if (RTE_UART1 == 1)
+#define UART1_DTR_PAD_INDEX             26     // GPIO11
+#define UART1_DTR_GPIO_INSTANCE         0
+#define UART1_DTR_GPIO_PIN              11
+
+#define UART1_RI_PAD_INDEX              44     // AONIO 4 = GPIO24
+#define UART1_RI_GPIO_INSTANCE          1
+#define UART1_RI_GPIO_PIN               8
+#define UART1_RI_PWM_INSTANCE           1
+#define UART1_RI_PWM_CLK_ID             FCLK_TIMER1
+#define UART1_RI_PWM_CLK_SEL            FCLK_TIMER1_SEL_26M
+
+#define UART1_DCD_PAD_INDEX             45     // AONIO 5 = GPIO25
+#define UART1_DCD_GPIO_INSTANCE         1
+#define UART1_DCD_GPIO_PIN              9
+#endif
+
+#if (RTE_UART2 == 1)
+#define UART2_DTR_PAD_INDEX             25     // GPIO10
+#define UART2_DTR_GPIO_INSTANCE         0
+#define UART2_DTR_GPIO_PIN              10
+
+#define UART2_RI_PAD_INDEX              43     // AONIO 3 = GPIO23
+#define UART2_RI_GPIO_INSTANCE          1
+#define UART2_RI_GPIO_PIN               7
+#define UART2_RI_PWM_INSTANCE           0
+#define UART2_RI_PWM_CLK_ID             FCLK_TIMER0
+#define UART2_RI_PWM_CLK_SEL            FCLK_TIMER0_SEL_26M
+
+#define UART2_DCD_PAD_INDEX             47     // AONIO 7 = GPIO27
+#define UART2_DCD_GPIO_INSTANCE         1
+#define UART2_DCD_GPIO_PIN              11
+#endif
+
+
+#define NETLIGHT_PAD_INDEX              46     // AONIO 6 = GPIO26
+#define NETLIGHT_PAD_ALT_FUNC           PAD_MUX_ALT5
+#define NETLIGHT_PWM_INSTANCE           3
+
+//USIM1 OPTION1
+#define USIM1_URST_OP1_PAD_INDEX             19     // GPIO4
+#define USIM1_URST_OP1_GPIO_INSTANCE         0
+#define USIM1_URST_OP1_GPIO_PIN              4
+#define USIM1_UCLK_OP1_PAD_INDEX             20     // GPIO5
+#define USIM1_UCLK_OP1_GPIO_INSTANCE         0
+#define USIM1_UCLK_OP1_GPIO_PIN              5
+#define USIM1_UIO_OP1_PAD_INDEX              21     // GPIO6
+#define USIM1_UIO_OP1_GPIO_INSTANCE          0
+#define USIM1_UIO_OP1_GPIO_PIN               6
+
+//USIM1 OPTION2
+#define USIM1_UIO_OP2_PAD_INDEX              27     // GPIO12
+#define USIM1_UIO_OP2_GPIO_INSTANCE          0
+#define USIM1_UIO_OP2_GPIO_PIN               12
+#define USIM1_URST_OP2_PAD_INDEX             28     // GPIO13
+#define USIM1_URST_OP2_GPIO_INSTANCE         0
+#define USIM1_URST_OP2_GPIO_PIN              13
+#define USIM1_UCLK_OP2_PAD_INDEX             29     // GPIO14
+#define USIM1_UCLK_OP2_GPIO_INSTANCE         0
+#define USIM1_UCLK_OP2_GPIO_PIN              14
+
+//USIM1 clock latched by AONIO, for example, use AONIO-6 test on EVB
+#define AONIO_6_PAD_INDEX        46     // AONIO 6 = GPIO26
+#define AONIO_6_GPIO_INSTANCE    1
+#define AONIO_6_GPIO_PIN         10
+
+#define RTE_CSPI0                       0
+
+#define RTE_CSPI0_MCLK_PAD_ADDR         39
+#define RTE_CSPI0_MCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI0_PCLK_PAD_ADDR         35
+#define RTE_CSPI0_PCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI0_CS_PAD_ADDR           36
+#define RTE_CSPI0_CS_FUNC               PAD_MUX_ALT1
+
+#define RTE_CSPI0_SDO0_PAD_ADDR         37
+#define RTE_CSPI0_SDO0_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI0_SDO1_PAD_ADDR         38
+#define RTE_CSPI0_SDO1_FUNC             PAD_MUX_ALT1
+
+// DMA CSPI0 Request ID
+#define RTE_CSPI0_DMA_RX_REQID          DMA_REQUEST_I2S0_RX
+
+// CSPI1 Configuration
+#define RTE_CSPI1                       1
+
+#define RTE_CSPI1_MCLK_PAD_ADDR         18
+#define RTE_CSPI1_MCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI1_PCLK_PAD_ADDR         19
+#define RTE_CSPI1_PCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI1_CS_PAD_ADDR           20
+#define RTE_CSPI1_CS_FUNC               PAD_MUX_ALT1
+
+#define RTE_CSPI1_SDO0_PAD_ADDR         21
+#define RTE_CSPI1_SDO0_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI1_SDO1_PAD_ADDR         22
+#define RTE_CSPI1_SDO1_FUNC             PAD_MUX_ALT1
+
+// DMA CSPI1 Request ID
+#define RTE_CSPI1_DMA_RX_REQID          DMA_REQUEST_I2S1_RX
+
+#endif  /* __RTE_DEVICE_H */

bsp/air780e/pikapython/requestment.txt

@@ -0,0 +1,2 @@
+pikascript-core==v1.12.4
+PikaStdLib==v1.12.4

bsp/air780e/src/main.c

@@ -0,0 +1,63 @@
+#include "common_api.h"
+#include "luat_rtos.h"
+#include "luat_debug.h"
+#include "luat_uart.h"
+#include "pikascript.h"
+
+#define USER_UART_ID LUAT_VUART_ID_0
+#define RX_BUF_LEN 1024
+
+typedef struct
+{
+    char buf[RX_BUF_LEN];
+    int pos;
+    int len;
+}rx_buf;
+
+static volatile rx_buf s_rx_buf = {.pos = 0, .len = 0};
+static luat_rtos_task_handle pika_main_handle;
+
+void luat_usb_recv_cb(int uart_id, uint32_t data_len){
+    s_rx_buf.len += luat_uart_read(uart_id, &s_rx_buf.buf[s_rx_buf.len], (data_len > (1024 - s_rx_buf.len)?(1024 - s_rx_buf.len):data_len));
+}
+
+int pika_platform_putchar(char ch) {
+    return luat_uart_write(USER_UART_ID, &ch, 1);
+}
+
+char pika_platform_getchar(void) {
+	while (s_rx_buf.pos >= s_rx_buf.len)
+	{
+		s_rx_buf.pos = 0;
+		s_rx_buf.len = 0;
+		luat_rtos_task_sleep(1);
+	}
+
+	return s_rx_buf.buf[s_rx_buf.pos++];;
+}
+
+static void pika_main(void *param)
+{
+	PikaObj * pikaMain = pikaScriptInit();
+
+    luat_uart_t uart = {
+        .id = USER_UART_ID,
+    };
+
+    luat_uart_setup(&uart);
+
+    luat_uart_ctrl(LUAT_VUART_ID_0, LUAT_UART_SET_RECV_CALLBACK, luat_usb_recv_cb);
+
+	while(1)
+	{
+		pikaScriptShell(pikaMain);
+	}
+}
+
+
+void pika_main_init(void)
+{
+	luat_rtos_task_create(&pika_main_handle, 4 * 1204, 50, "pika_main", pika_main, NULL, 32);
+}
+
+INIT_TASK_EXPORT(pika_main_init, "0");

bsp/air780e/xmake.lua

@@ -0,0 +1,33 @@
+local TARGET_NAME = "PikaPython"
+local LIB_DIR = "$(buildir)/".. TARGET_NAME .. "/"
+local LIB_NAME = "lib" .. TARGET_NAME .. ".a "
+
+target(TARGET_NAME)
+    set_kind("static")
+    set_targetdir(LIB_DIR)
+
+    --加入代码和头文件
+    add_includedirs("/inc",{public = true})
+    add_files("/src/*.c",{public = true})
+    add_includedirs("/pikapython/pikascript-api",{public = true})
+    add_files("/pikapython/pikascript-api/*.c",{public = true})
+    add_includedirs("/pikapython/pikascript-core",{public = true})
+    add_files("/pikapython/pikascript-core/*.c",{public = true})
+    add_includedirs("/pikapython/pikascript-lib/PikaStdLib",{public = true})
+    add_files("/pikapython/pikascript-lib/PikaStdLib/*.c",{public = true})
+
+    --路径可以随便写,可以加任意路径的代码,下面代码等效上方代码
+    -- add_includedirs(SDK_TOP .. "project/" .. TARGET_NAME .. "/inc",{public = true})
+    -- add_files(SDK_TOP .. "project/" .. TARGET_NAME .. "/src/*.c",{public = true})
+
+    -- 按需链接mbedtls
+    -- add_defines("MBEDTLS_CONFIG_FILE=\"config_ec_ssl_comm.h\"")
+    -- add_files(SDK_TOP .. "PLAT/middleware/thirdparty/mbedtls/library/*.c")
+    -- 按需编译httpclient
+    -- add_files(SDK_TOP .. "PLAT/middleware/thirdparty/httpclient/*.c")
+
+    --可以继续增加add_includedirs和add_files
+    --自动链接
+    LIB_USER = LIB_USER .. SDK_TOP .. LIB_DIR .. LIB_NAME
+    --甚至可以加入自己的库
+target_end()