sdk-bsp-stm32h750-realthread-artpi/libraries/Kconfig

menu "Hardware Drivers Config"
config SOC_STM32H750XB
    bool
    select SOC_SERIES_STM32H7
    select RT_USING_COMPONENTS_INIT
    default y

config SOC_SERIES_STM32H7
    bool
    select ARCH_ARM_CORTEX_M7
    select SOC_FAMILY_STM32

menu "Board extended module"

    menuconfig ART_PI_USING_MEDIA_IO
        bool "Media-IO"
        default n
        if ART_PI_USING_MEDIA_IO
            config BSP_USING_SPI_LCD_ILI9488
                bool
            config PKG_USING_PERSIMMON_SRC
                bool

            config MEDIA_IO_USING_SCREEN
                select BSP_USING_SPI
                select BSP_USING_SPI2
                select BSP_USING_SDRAM
                select BSP_USING_SPI_LCD_ILI9488
                select PKG_USING_PERSIMMON_SRC
                bool "Enable Screen"
                default y
            config MEDIA_IO_USING_TOUCH
                select RT_USING_I2C
                select RT_USING_I2C_BITOPS
                select BSP_USING_I2C
                select BSP_USING_I2C2
                select PKG_USING_TOUCH_DRIVERS
                select PKG_USING_FT6236
                bool "Enable Touch"
                default y
            config MEDIA_IO_USING_AUDIO
                select RT_USING_AUDIO
                select RT_USING_I2C
                select RT_USING_I2C_BITOPS
                select BSP_USING_I2C
                select BSP_USING_I2C3
                bool "Enable Audio"
                default y
                if MEDIA_IO_USING_AUDIO
                    config AUDIO_MP3
                    bool "Support MP3"
                    select PKG_USING_HELIX
                    default y
                endif
        endif

    menuconfig ART_PI_USING_INDUSTRY_IO
        bool "Industry-IO"
        default n
        if ART_PI_USING_INDUSTRY_IO
            config INDUSTRY_IO_USING_ETH
                select BSP_USING_ETH
                select PHY_USING_LAN8720A
                bool "Enable Ethernet"
                default y
        endif
        
endmenu

menu "Onboard Peripheral"

    config BSP_USING_USB_TO_USART
        bool "Enable Debuger USART (uart4)"
        select BSP_USING_UART
        select BSP_USING_UART4
        default n

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (spi1)"
        select BSP_USING_SPI
        select BSP_USING_SPI1
        select RT_USING_FAL
        select FAL_USING_SFUD_PORT
        select RT_USING_SFUD
        default n
        
    config BSP_USING_QSPI_FLASH
        bool "Enable QSPI FLASH (w25q64 qspi)"
        select BSP_USING_QSPI
        select FAL_USING_SFUD_PORT
        select RT_USING_SFUD
        select RT_SFUD_USING_QSPI
        default n

    config BSP_USING_WIFI
        bool "Enable wifi (AP6212)"
        select ART_PI_USING_WIFI_6212_LIB
        select ART_PI_USING_OTA_LIB
        select BSP_USING_SPI_FLASH
        select RT_USING_WIFI
        select RT_USING_SAL
        default n

    config BSP_USING_OV2640
        bool "Enable camera (ov2640)"
        select BSP_USING_DCMI
        select BSP_USING_I2C
        select BSP_USING_I2C2
        default n

    config BSP_USING_GC0328C
        bool "Enable camera (gc0328)"
        select BSP_USING_DCMI
        select BSP_USING_I2C
        select BSP_USING_I2C2
        default n

    menuconfig BSP_USING_LVGL
        bool "Enable LVGL for LCD"
        select PKG_USING_LVGL
        select PKG_USING_LV_MUSIC_DEMO
        default n
        if BSP_USING_LVGL      
            config BSP_USING_ILI9488
                bool "Enable LVGL for LCD_ILI9488"
                select BSP_USING_SPI_LCD_ILI9488
                default n
            config BSP_USING_LCD_RGB
                bool "Enable LVGL for LCD_RGB565"
                select BSP_USING_LCD
                select RT_TOUCH_PIN_IRQ
                default n
                if BSP_USING_LCD_RGB
                    config BSP_USING_TOUCH
                    select BSP_USING_I2C
                    select BSP_USING_I2C1
                    bool "enable Touch GT9147"
                    select PKG_USING_GT9147                    
                    default n
                endif
        endif

    menuconfig BSP_USING_FS
        bool "Enable filesystem"
        select RT_USING_DFS
        select RT_USING_DFS_ROMFS
        select RT_USING_POSIX_FS
        default n
        if BSP_USING_FS
            config BSP_USING_SDCARD_FS
                bool "Enable SDCARD filesystem"
                select BSP_USING_SDIO
                select BSP_USING_SDIO1
                select RT_USING_DFS_ELMFAT
                default n
            config BSP_USING_SPI_FLASH_FS
                bool "Enable SPI FLASH filesystem"
                select BSP_USING_SPI_FLASH
                select RT_USING_MTD_NOR
                select PKG_USING_LITTLEFS
                default n
        endif

endmenu

menu "On-chip Peripheral"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default n
        select RT_USING_SERIAL
        select RT_SERIAL_USING_DMA
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default n

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART1_TX_USING_DMA
                bool "Enable UART1 TX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n
                
            config BSP_USING_UART3
                bool "Enable UART3"
                default n
                
            config BSP_USING_UART4
                bool "Enable UART4"
                default n
                
            config BSP_USING_UART6
                bool "Enable UART6"
                default n
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1"
                default n
            config BSP_USING_SPI2
                bool "Enable SPI2"
                default n
            config BSP_USING_SPI4
                bool "Enable SPI4"
                default n
        endif
        
    config BSP_USING_QSPI
        bool "Enable QSPI BUS"
        select RT_USING_QSPI
        select RT_USING_SPI
        default n

    menuconfig BSP_USING_I2C
        bool "Enable I2C BUS (software simulation)"
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        default n
        if BSP_USING_I2C
            menuconfig BSP_USING_I2C1
                bool "Enable I2C1 BUS (software simulation)"
                default n
                select RT_USING_I2C
                select RT_USING_I2C_BITOPS
                select RT_USING_PIN
                if BSP_USING_I2C1
                    comment "Notice: PB6 --> 22; PB7 --> 23" 
                    config BSP_I2C1_SCL_PIN
                        int "I2C1 scl pin number"
                        range 0 175
                        default 22
                    config BSP_I2C1_SDA_PIN
                        int "I2C1 sda pin number"
                        range 0 175
                        default 23
                endif
            menuconfig BSP_USING_I2C2
                bool "Enable I2C2 BUS (software simulation)"
                default n
                if BSP_USING_I2C2
                    comment "Notice: PH13 --> 125; PH15 --> 127"
                    config BSP_I2C2_SCL_PIN
                        int "i2c2 scl pin number"
                        range 1 176
                        default 127
                    config BSP_I2C2_SDA_PIN
                        int "I2C2 sda pin number"
                        range 0 175
                        default 125
                endif
            menuconfig BSP_USING_I2C3
                bool "Enable I2C3 BUS (software simulation)"
                default n
                if BSP_USING_I2C3
                    comment "Notice: PH12 --> 124; PH11 --> 123"
                    config BSP_I2C3_SCL_PIN
                        int "i2c3 scl pin number"
                        range 0 175
                        default 123
                    config BSP_I2C3_SDA_PIN
                        int "I2C3 sda pin number"
                        range 0 175
                        default 124
                endif
        endif
		
    menuconfig BSP_USING_SDIO
        bool "Enable SDIO"
        default n
        select RT_USING_SDIO
        if BSP_USING_SDIO
            config BSP_USING_SDIO1
                bool "Enable SDIO1"
                default n
            config BSP_USING_SDIO2
                bool "Enable SDIO2"
                default n
        endif

    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        default n

    menuconfig BSP_USING_ETH
        bool "Enable Ethernet"
        default n        
        select RT_USING_LWIP
        if BSP_USING_ETH
            config ETH_RESET_PIN
                string "ETH RESET PIN"
                default "PA.3"
        endif
        if BSP_USING_ETH
            choice
                prompt "Choose ETH PHY"
                default PHY_USING_LAN8720A
                        config PHY_USING_LAN8720A
                    bool "USING LAN8720A"
                    default n
            endchoice
        endif

    config BSP_USING_LCD
        bool "Enable LCD"
        select BSP_USING_GPIO
        select BSP_USING_SDRAM
        select RT_USING_MEMHEAP
        default n

    config BSP_USING_DCMI
        bool "Enable DCMI"
        default n
        
    menuconfig BSP_USING_FDCAN
        bool "Enable FDCAN"
        default n
        select RT_USING_CAN
        if BSP_USING_FDCAN
            config BSP_USING_FDCAN1
                bool "USING FDCAN1"
                default n
        endif
        
    config BSP_USING_USBD
        bool "Enable USB Device"
        select RT_USING_USB_DEVICE
        default n
        
    menuconfig BSP_USING_USBH
        bool "Enable USB Host"
        select RT_USING_USB_HOST
        default n
        if BSP_USING_USBH
            menuconfig RT_USBH_MSTORAGE
                bool "Enable Udisk Drivers"
                select RT_USING_DFS
                select RT_USING_DFS_ELMFAT
                default n
                if RT_USBH_MSTORAGE
                    config UDISK_MOUNTPOINT
                        string "Udisk mount dir"
                        default "/"
                endif
        endif
        
    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM13
                bool "Enable TIM13"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM5
            bool "Enable Timer5 output pwm"
            default n
            if BSP_USING_PWM5
                config BSP_USING_PWM5_CH1
                    bool "Enable PWM5 channel1"
                    default n
            endif
        config SAMPLES_USING_PWM
            bool "SAMPLE PWM5 channel1"
            default n
        endif

    config BSP_USING_ONCHIP_RTC
        bool "Enable Onchip RTC"
        select RT_USING_RTC
        default n
endmenu

endmenu

menu "External Libraries"

    config ART_PI_USING_WIFI_6212_LIB
        bool "Using Wifi(AP6212) Library"
        select BSP_USING_SDIO
        select BSP_USING_SDIO2
        select RT_USING_LWIP
        select RT_USING_WIFI
        default n

    config ART_PI_USING_OTA_LIB
        bool "Using RT-Thread OTA Library"
        select RT_USING_FAL
        select FAL_USING_SFUD_PORT
        select RT_USING_SFUD
        select RT_USING_RYM
        default n

    config ART_PI_TouchGFX_LIB
        bool "Using TouchGFX Library"
        select BSP_USING_LCD
        select RT_USING_CPLUSPLUS
        default n
    
    config ART_PI_USING_FTP_LIB
        bool "Using FTP Library"
        select RT_USING_SAL
        select SAL_USING_POSIX
        select RT_USING_DFS
        default n

endmenu

choice
    prompt "The target of download and execute firmware"
    default FIRMWARE_EXEC_USING_QSPI_FLASH

    config FIRMWARE_EXEC_USING_QSPI_FLASH
        bool "QSPI Flash"

    config FIRMWARE_EXEC_USING_QEMU
        bool "QEMU"

endchoice