| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149 |
- AppVersion = 48901
- [GENERAL]
- ConnectMode = 0
- CurrentFile = ""
- DataFileSAddr = 0x05000000
- GUIMode = 0
- HostName = ""
- TargetIF = 0
- USBPort = 0
- USBSerialNo = 0x00000000
- [JTAG]
- Device0_ID = 0x1D001447
- Device0_IRLen = 0x00000008
- Device0_Name = "RX610 Core"
- IRLen = 0
- MultipleTargets = 2
- NumDevices = 1
- Speed0 = 12000
- Speed1 = 12000
- TAP_Number = 0
- UseAdaptive0 = 0
- UseAdaptive1 = 0
- UseMaxSpeed0 = 0
- UseMaxSpeed1 = 0
- [CPU]
- CheckCoreID = 1
- ChipName = "Renesas R5F56108"
- ClockSpeed = 0x00000000
- Core = 0x0D00FFFF
- CoreID = 0x1D001447
- CoreIDMask = 0xFFFFFFFF
- DeviceFamily = 0x0000000D
- EndianMode = 0
- HasInternalFlash = 1
- InitStep0_Action = "Reset"
- InitStep0_Comment = "Reset and halt target"
- InitStep0_Value0 = 0x00000000
- InitStep0_Value1 = 0x00000000
- InitStep10_Action = "Write 8bit"
- InitStep10_Comment = "// PFCR4: Enable A15-A8"
- InitStep10_Value0 = 0x0008C104
- InitStep10_Value1 = 0x000000FF
- InitStep11_Action = "Write 8bit"
- InitStep11_Comment = "// PA_DDR: Enable output of A0-A7. Not handled via PFCR..."
- InitStep11_Value0 = 0x0008C00A
- InitStep11_Value1 = 0x000000FF
- InitStep12_Action = "Write 8bit"
- InitStep12_Comment = "// PFCR5: Enable D15-D8 and WR#1 / BC1# "
- InitStep12_Value0 = 0x0008C105
- InitStep12_Value1 = 0x00000050
- InitStep1_Action = "Write 16bit"
- InitStep1_Comment = "// SYSCR0: Enable extended mode, to make external bus interface accessible"
- InitStep1_Value0 = 0x00080006
- InitStep1_Value1 = 0x00005A03
- InitStep2_Action = "Write 16bit"
- InitStep2_Comment = "// CS3MOD: Single write strobe mode"
- InitStep2_Value0 = 0x00083032
- InitStep2_Value1 = 0x00000001
- InitStep3_Action = "Write 32bit"
- InitStep3_Comment = "// CS3WCNT1: Page read/write wait cycles"
- InitStep3_Value0 = 0x00083034
- InitStep3_Value1 = 0x02020101
- InitStep4_Action = "Write 32bit"
- InitStep4_Comment = "// CS3WCNT2: R/W acc, data out wait-cycles"
- InitStep4_Value0 = 0x00083038
- InitStep4_Value1 = 0x01100111
- InitStep5_Action = "Write 16bit"
- InitStep5_Comment = "// CS3CNT: Enable nCS3, 16-bit ExtBus"
- InitStep5_Value0 = 0x00083832
- InitStep5_Value1 = 0x00000001
- InitStep6_Action = "Write 16bit"
- InitStep6_Comment = "// CS3REC: No recovery cycles"
- InitStep6_Value0 = 0x0008383A
- InitStep6_Value1 = 0x00000000
- InitStep7_Action = "Write 8bit"
- InitStep7_Comment = "// PFCR0: Enable functionality of nCS3"
- InitStep7_Value0 = 0x0008C100
- InitStep7_Value1 = 0x00000008
- InitStep8_Action = "Write 8bit"
- InitStep8_Comment = "// PFCR2: Enable nCS3 on P63"
- InitStep8_Value0 = 0x0008C102
- InitStep8_Value1 = 0x00000000
- InitStep9_Action = "Write 8bit"
- InitStep9_Comment = "// PFCR3: Enable A23-A16"
- InitStep9_Value0 = 0x0008C103
- InitStep9_Value1 = 0x000000FF
- NumExitSteps = 0
- NumInitSteps = 13
- RAMAddr = 0x00000000
- RAMSize = 0x00020000
- ScriptFile = ""
- UseAutoSpeed = 0x00000001
- UseRAM = 1
- UseScriptFile = 0
- [FLASH]
- NumBanks = 2
- [FLASH0]
- aSectorSel[28] = 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
- AutoDetect = 0
- BankName = ""
- BankSelMode = 1
- BaseAddr = 0xFFE00000
- CheckId = 0
- CustomRAMCode = ""
- DeviceName = "R5F56108 internal"
- EndBank = 27
- OrgNumBits = 32
- OrgNumChips = 1
- StartBank = 0
- UseCustomRAMCode = 0
- [FLASH1]
- aSectorSel[0] =
- AutoDetect = 1
- BankName = ""
- BankSelMode = 1
- BaseAddr = 0x05000000
- CheckId = 3
- CustomRAMCode = ""
- DeviceName = "Auto detected flash memory"
- EndBank = 8191
- OrgNumBits = 16
- OrgNumChips = 1
- StartBank = 0
- UseCustomRAMCode = 0
- [PRODUCTION]
- AutoPerformsErase = 1
- AutoPerformsHardLock = 0
- AutoPerformsHardUnlock = 0
- AutoPerformsProgram = 1
- AutoPerformsSecure = 0
- AutoPerformsSoftLock = 0
- AutoPerformsSoftUnlock = 1
- AutoPerformsStartApp = 0
- AutoPerformsUnsecure = 0
- AutoPerformsVerify = 1
- EnableProductionMode = 0
- EnableTargetPower = 0
- EraseType = 2
- ProductionDelay = 0x000001F4
- ProductionThreshold = 0x00000BB8
- ProgramSN = 0
- SerialFile = ""
- SNAddr = 0x00000000
- SNInc = 0x00000001
- SNLen = 0x00000008
- SNListFile = ""
- SNValue = 0x00000001
- TargetPowerDelay = 0x00000014
- VerifyType = 1
|
