sdk-debuger-jlink/Samples/JFlash/ProjectFiles/Spansion/MB9EF226.JLinkScript

/*****************************************************************************/
/*               (C) Fujitsu Semiconductor Europe GmbH (FSEU)                */
/*                                                                           */
/* The following software deliverable is intended for and must only be       */
/* used for reference and in an evaluation laboratory environment.           */
/* It is provided on an as-is basis without charge and is subject to         */
/* alterations.                                                              */
/* It is the user's obligation to fully test the software in its             */
/* environment and to ensure proper functionality, qualification and         */
/* compliance with component specifications.                                 */
/*                                                                           */
/* In the event the software deliverable includes the use of open            */
/* source components, the provisions of the governing open source            */
/* license agreement shall apply with respect to such software               */
/* deliverable.                                                              */
/* FSEU does not warrant that the deliverables do not infringe any           */
/* third party intellectual property right (IPR). In the event that          */
/* the deliverables infringe a third party IPR it is the sole                */
/* responsibility of the customer to obtain necessary licenses to            */
/* continue the usage of the deliverable.                                    */
/*                                                                           */
/* To the maximum extent permitted by applicable law FSEU disclaims all      */
/* warranties, whether express or implied, in particular, but not            */
/* limited to, warranties of merchantability and fitness for a               */
/* particular purpose for which the deliverable is not designated.           */
/*                                                                           */
/* To the maximum extent permitted by applicable law, FSEU's liability       */
/* is restricted to intentional misconduct and gross negligence.             */
/* FSEU is not liable for consequential damages.                             */
/*                                                                           */
/* (V1.5)                                                                    */
/*****************************************************************************/
/** \file Default.JLinkScript
 **
 **
 ** History:
 **   - 2012-09-07    1.00    ZWu    Initial version for Fujitsu MB9DF126
 **
 *****************************************************************************/

/*****************************************************************************
*  For further information refer to the following documents:
*
*  - "ARM Debug Interface v5 Architecture Specification"
*    ARM: IHI0031A_ARM_debug_interface_v5.pdf
*  - "Cortex-R4 and Cortex-R4F (Revision r1p3) Technical Reference Manual"
*    ARM: DDI0363E_cortexr4_r1p3_trm.pdf
*  - "J-Link / J-Trace User Guide"
*    SEGGER: UM08001_JLink.pdf
*
*****************************************************************************/


// ###################################################################
//  H E L P E R   F U N C T I O N S
// ###################################################################

/*********************************************************************
*
*  _SelDP
*
*  Selects the Debug Port register set as the DR scan chain
*/
void _SelDP(void)
{
    JTAG_StoreIR(0xa);   // Updates Instruction Register scan chain
    JTAG_StoreClocks(1); // Transition from "Update-IR" to "Run-Test/Idle" state of Debug TAP
}

/*********************************************************************
*
*  _SelAP
*
*  Selects the Access Port register set as the DR scan chain
*/
void _SelAP(void)
{
    JTAG_StoreIR(0xb);   // Updates Instruction Register scan chain
    JTAG_StoreClocks(1); // Transition from "Update-IR" to "Run-Test/Idle" state of Debug TAP
}

/*********************************************************************
*
*       _StoreTriggerReadAPDPReg
*
*  Function description
*    Triggers a read of an AP or DP register. Depends on the previous command (DPACC / APACC)
*/
int _StoreTriggerReadAPDPReg(unsigned int RegIndex) {
  U32 v;
  int BitPos;
  //
  // Write 35 bits (32 bits data, 2 bits addr, 1 bit RnW)
  //
  v  = 1;                // 1 indicates read access
  v |= (RegIndex << 1);
  JLINK_JTAG_StartDR();
  BitPos = JLINK_JTAG_WriteDRCont(v, 3);
  v = 0;
  JLINK_JTAG_WriteDREnd(v, 32);
  JTAG_StoreClocks(8);
  return BitPos;
}

/*********************************************************************
*
*       _StoreWriteAPDPReg
*
*  Function description
*    Writes an AP or DP register. Depends on the previous command (DPACC / APACC)
*/
int _StoreWriteAPDPReg(unsigned int RegIndex, U32 Data) {
  U32 v;
  int BitPos;
  //
  // Write 35 bits (32 bits data, 2 bits addr, 1 bit RnW)
  //
  v = 0;   // 0 indicates write access
  v |= (RegIndex << 1);
  JLINK_JTAG_StartDR();
  BitPos = JLINK_JTAG_WriteDRCont(v, 3);
  v = Data;
  JLINK_JTAG_WriteDREnd(v, 32);
  JTAG_StoreClocks(8);
  return BitPos;
}

/*********************************************************************
*
*  _GetReadData
*
*  Returns the actual 32-bit read data from the specified register.
*  In order to get the wanted read data, a further action must be done
*  after the actual read access to shift the read data out of the scan
*  chain. This is done by reading the RDBUFF register in the DP which
*  is intended for this use case (a read to this register returns 0 and
*  has no side effects on the system)
*
*  Parameter:
*  - u32RegIndex:        0-3 (selects which of the 4 registers shall be read)
*  - cSelectApOnReturn:  If 0, DP is selected when function returns
*                        otherwise AP will be selected. Since no
*                        global variables are supported by JLinkScript
*                        the state cannot be restored in another way...
*
*  Return value:
*  - u32Data:            Read data
*/
unsigned int _GetReadData(unsigned int u32RegIndex, char cSelectApOnReturn)
{
    unsigned int u32Data;
    unsigned int u32BitPosData;

    // Trigger read to move wanted data in the DR scan chain
    _StoreTriggerReadAPDPReg(u32RegIndex); 
    // Trigger read from RDBUFF register to shift out the wanted read data
    _SelDP();
    u32BitPosData = _StoreTriggerReadAPDPReg(3);
    u32Data = JTAG_GetU32(u32BitPosData + 3);
    
    if (cSelectApOnReturn != 0)
    {
        _SelAP();
    }
    
    return u32Data;
}


/*********************************************************************
*
*  _WriteViaAhb
*
*  Writes to the MCU via the AHB-AP
*
*  Parameter:
*  - u32Address: Address for write action (as required by AHB master)
*  - u32Data:    Data that shall be written
*/
void _WriteViaAhb(unsigned int u32Address, unsigned int u32Data)
{
    _SelDP();
    _StoreWriteAPDPReg(2, 0x00000000);  // Bank 0x0 of AHB-AP (0x00) selected
    
    _SelAP();
    _StoreWriteAPDPReg(1, u32Address);  // Set TAR register of AP
    _StoreWriteAPDPReg(3, u32Data);     // Write via DRW register of AP
}

/*********************************************************************
*
*  _ReadViaAhb
*
*  Reads from the MCU via the AHB-AP
*
*  Parameter:
*  - u32Address: Address for read action (as required by AHB master)
*
*  Return value:
*  - u32Data:    Data that has been read
*/
unsigned int _ReadViaAhb(unsigned int u32Address)
{
    unsigned int u32Data;

    _SelDP();
    _StoreWriteAPDPReg(2, 0x00000000); // Bank 0x0 of AHB-AP (0x00) selected
    _SelAP();

    _StoreWriteAPDPReg(1, u32Address); // Set TAR register of AP
    u32Data = _GetReadData(3, 0); // Read via DRW register of AP
    return u32Data;
}

/*********************************************************************
*
*  _WriteViaApb
*
*  Writes to the MCU via the APB-AP
*
*  Parameter:
*  - u32Address: Address for write action (as required by APB master)
*  - u32Data:    Data that shall be written
*/
void _WriteViaApb(unsigned int u32Address, unsigned int u32Data)
{
    _SelDP();
    _StoreWriteAPDPReg(2, 0x01000000);  // Bank 0x0 of APB-AP (0x01) selected
    
    _SelAP();
    _StoreWriteAPDPReg(1, u32Address);  // Set TAR register of AP
    _StoreWriteAPDPReg(3, u32Data);     // Write via DRW register of AP
}

/*********************************************************************
*
*  _ReadViaApb
*
*  Reads from the MCU via the APB-AP
*
*  Parameter:
*  - u32Address: Address for read action (as required by APB master)
*
*  Return value:
*  - u32Data:    Data that has been read
*/
unsigned int _ReadViaApb(unsigned int u32Address)
{
    unsigned int u32Data;

    _SelDP();
    _StoreWriteAPDPReg(2, 0x01000000); // Bank 0x0 of APB-AP (0x01) selected
    
    _SelAP();

    _StoreWriteAPDPReg(1, u32Address); // Set TAR register of AP
    u32Data = _GetReadData(3, 0); // Read via DRW register of AP
    return u32Data;
}

/*********************************************************************
*
*  _GetAndClearStickyError
*
*  Checks if an error occurred after the last invocation of this function
*  This means the function can be called after several read/write actions
*  to check if this group of actions has been processed successfully
*
*  Return value:
*  - cStickyErrorFlag:    0 if no sticky error has occurred otherwise 1
*/
char _GetAndClearStickyError(void)
{
    unsigned int u32Data;
    char cStickyErrorFlag;

    _SelDP();
    u32Data = _GetReadData(1, 0);

    // Clear only Sticky Error Flag ('1' clears sticky flags)
    _StoreWriteAPDPReg(1, ((u32Data & 0xffffffcd) | 0x20));
    if((u32Data & 0x20) == 0)
    {
        cStickyErrorFlag = 0;
    }
    else
    {
        cStickyErrorFlag = 1;
    }
    return cStickyErrorFlag;
}



// ###################################################################
//  U S E R   F U N C T I O N S
// ###################################################################


/*********************************************************************
*
*  ResetJtag
*
*  Resets the JTAG (and hence debug logic) for the specified time (ms)
*  by asserting nTRST pin
*
*  Parameter:
*  - u32ResetDuration:   Time in [ms] the reset signal is asserted
*/
void ResetJtag(unsigned int u32ResetDuration)
{
    JTAG_TRSTPin = 0;
    SYS_Sleep(u32ResetDuration);
    JTAG_TRSTPin = 1;
    Report("--- FSEU script --- JTAG reset");
}


/*********************************************************************
*
*  ResetMcu
*
*  Resets the MCU for the specified time (ms) via JTAG connector pin 15
*
*  Parameter:
*  - u32ResetDuration:   Time in [ms] the reset signal is asserted
*/
void ResetMcu(unsigned int u32ResetDuration)
{
    JTAG_ResetPin = 0;
    SYS_Sleep(u32ResetDuration);
    JTAG_ResetPin = 1;
    Report("--- FSEU script --- MCU reset");
}


/*********************************************************************
*
*  ResetAllAndSetDebuggerConnectedFlag
*
*  Resets the MCU via JTAG connector pin 15 and the JTAG via nTRST pin
*  Outputs >= 16 TCK clock cycles so that SYSC_JTAGDETECT_DBGCON is set.
*  It is used by the BootROM as the criteria for enabling the debugger
*  wait time before branching to application (if not disabled by Flash
*  marker setting in Boot Description Record)
*  SYSC_JTAGDETECT_DBGCON will only be reset by JTAG nTRST and not by
*  any MCU hard reset. Therefore, this clocking is only required once
*  during initialisation.
*
*  TMS signal is 0 while JTAG_WriteClocks() outputs clock cycles
*  As the Debug TAP state machine is reset by nTRST assertion, this
*  also ensures that the Debug TAP state machine transitions to and
*  stays in "Run-Test/Idle" state. Other functions in this file
*  require that the Debug TAP state machine is in "Run-Test/Idle"
*  before calling them
*
*
*  RSTx  --_________________________________ ... ________________---
*  nTRST ----__----------------------------- ... -------------------
*  TCK   --------|_|-|_|-|_|-|_|-|_|-|_|-|_| ... -|_|-|_|-----------
*  TMS   ___________________________________________________________
*/
void ResetAllAndSetDebuggerConnectedFlag()
{
    JTAG_ResetPin = 0;
    JTAG_TRSTPin = 0;
    SYS_Sleep(1);
    JTAG_TRSTPin = 1;
    JTAG_WriteClocks(20); 
    JTAG_ResetPin = 1;
    Report("--- FSEU script --- MCU & JTAG reset, SYSC_JTAGDETECT_DBGCON should be set now");
}


/*********************************************************************
*
*  GetId
*
*  Selects and reads the Debug TAP IDCODE scan chain
*/
void GetId(void)
{
    unsigned int u32BitPos;
    unsigned int u32Value;

    // Select the IDCODE register for the DR scan chain
    JTAG_StoreIR(0x0E);
    JTAG_StoreClocks(1);
    // Read ID
    u32Value = 0;
    u32BitPos = JTAG_StoreDR(u32Value, 32);
    JTAG_WriteClocks(1);
    u32Value = JTAG_GetU32(u32BitPos);
    
    if(u32Value == 0x4ba00477)
    {
        Report("--- FSEU script --- OK: ARM JTAG-DP detected (JTAG IDCODE: 0x4ba00477)");
    }
    else
    {
//        Report1("--- FSEU script --- ERROR: JTAG IDCODE unknown -> ",u32Value);
    }
}


/*********************************************************************
*
*  PowerUpDebugPort
*
*  Sets the "power request bits" (CSYSPWRUPREQ, CDBGPWRUPREQ) in the
*  DP CTRL/STAT register and waits for their acknowledgement.
*
*  Return value:
*  - cError:    0 if power-up was successful otherwise 1
*/
char PowerUpDebugPort(void)
{
    char cBreak;
    char cError;
    unsigned int u32ReadData;
    unsigned int u32TimeOut;

    // Set CxxxPWRUPREQ bits and also clear sticky error flags, enable overrun detection
    _SelDP();
    _StoreWriteAPDPReg(1, 0x50000033);
    
    u32TimeOut = 100;
    cBreak = 0;
    while(cBreak == 0)
    {
        u32TimeOut -= 1;
        
        u32ReadData = _GetReadData(1, 0);
        
        // Check if CxxxPWRUPREQ and CxxxPWRUPACK bits are set
        if ((u32ReadData >> 28) == 0xf)
        {
            cBreak = 1;
            cError = 0;
            Report("--- FSEU script --- OK: Debug port powered up");
        }
        else if (u32TimeOut == 0)
        {
            cBreak = 1;
            cError = 1;
            Report("--- FSEU script --- ERROR: Could not power up debug port (time-out reached)!");
        }
    }
    return cError;
}


/*********************************************************************
*
*  InitAccessPorts
*
*  Initializes APB and AHB Access Port registers to their default value.
*  These registers may be in an unknown state because they are not
*  reset by an MCU hard reset. But the functions in here may rely on a 
*  defined state...
*/
void InitAccessPorts(void)
{
    // AHB Access Port
    // ---------------
    _SelDP();
    // Write DP APSEL register: Bank 0x0 of AHB-AP (AP-ID: 0x00) selected
    _StoreWriteAPDPReg(2, 0x00000000);
    _SelAP();
    
    _StoreWriteAPDPReg(0, 0x43000002); // Write CSW register of AHB-AP
    
    // APB Access Port
    // ---------------
    _SelDP();
    // Write DP APSEL register: Bank 0x0 of APB-AP (AP-ID: 0x01) selected
    _StoreWriteAPDPReg(2, 0x01000000);
    _SelAP();
    
    _StoreWriteAPDPReg(0, 0x80000002); // Write CSW register of APB-AP
}


/*********************************************************************
*
*  ReportStat2Value
*
*  Reports the current value of SCCFG_STAT2 register
*
*  Return value:
*  - cError:    0 if SCCFG_STAT2 could be read successful otherwise 1
*/
char ReportStat2Value(void)
{
    unsigned int u32SccfgStat2AddressApb;
    unsigned int u32SccfgStat2Value;
    char cError;
    
    cError = 0;

    // Addresses as required for access via APB-AP
    u32SccfgStat2AddressApb = 0x0000f180;

    _GetAndClearStickyError();

    u32SccfgStat2Value = _ReadViaApb(u32SccfgStat2AddressApb);

    if(_GetAndClearStickyError() == 1)
    {
        cError = 1;
        Report("--- FSEU script --- ERROR: Reading SCCFG_STAT2 caused the StickyError flag to be set!");
    }
    else
    {
//        Report1("--- FSEU script --- SCCFG_STAT2 = ", u32SccfgStat2Value);
    }
  
    return cError;
}

/*********************************************************************
*
*  ReportGpreg1Value
*
*  Reports the current value of SCCFG_GPREG1 register which contains
*  further BootROM status information (if not overwritten by user
*  application)
*
*  Return value:
*  - cError:    0 if SCCFG_GPREG1 could be read successful otherwise 1
*/
char ReportGpreg1Value(void)
{
    unsigned int u32SccfgGpreg1AddressApb;
    unsigned int u32SccfgGpreg1Value;
    char cError;
    
    cError = 0;

    // Addresses as required for access via APB-AP
    u32SccfgGpreg1AddressApb = 0x0000f1ac;

    _GetAndClearStickyError();

    u32SccfgGpreg1Value = _ReadViaApb(u32SccfgGpreg1AddressApb);

    if(_GetAndClearStickyError() == 1)
    {
        cError = 1;
        Report("--- FSEU script --- ERROR: Reading SCCFG_GPREG1 caused the StickyError flag to be set!");
    }
    else
    {
//        Report1("--- FSEU script --- SCCFG_GPREG1 = ", u32SccfgGpreg1Value);
    }
  
    return cError;
}


/*********************************************************************
*
*  UnlockDevice
*
*  If the MCU is secured, the passed security key will be entered
*  in the Security Checker module to unlock the MCU.
*  Otherwise this step is skipped
*
*  Note: Security key can be entered at any time, the result of key
*        entering will be available after SCCFG_STAT2_DBGRDY is set.
*
*  Parameter:
*  - u32KeyBytes0_3:   Part of the key for register SCCFG_SECKEY0
*  - u32KeyBytes4_7:   Part of the key for register SCCFG_SECKEY1
*  - u32KeyBytes8_11:  Part of the key for register SCCFG_SECKEY2
*  - u32KeyBytes12_15: Part of the key for register SCCFG_SECKEY3
*
*  Return value:
*  - cError:    0 if unlocking was successful otherwise 1
*/
char UnlockDevice(unsigned int u32KeyBytes0_3, unsigned int u32KeyBytes4_7, unsigned int u32KeyBytes8_11, unsigned int u32KeyBytes12_15)
{
    char cError;
    unsigned int u32SccfgStat2Value;
    unsigned int u32SccfgStat2AddressApb;
    unsigned int u32SccfgUnlckAddressApb;
    unsigned int u32SccfgSeckey0AddressApb;
    unsigned int u32RegisterUnlockKey;
    unsigned int u32RegisterLockKey;
    unsigned int u32SccfgGpreg1AddressApb;
    unsigned int u32SccfgGpreg1Value;
    
    cError = 0;
    
    // Addresses as required for access via APB-AP
    u32SccfgStat2AddressApb   = 0x0000f180;
    u32SccfgSeckey0AddressApb = 0x0000f190;
    u32SccfgUnlckAddressApb   = 0x0000f1a4;
    u32SccfgGpreg1AddressApb  = 0x0000f1ac;

    // Security Checker Register Unlock/Lock Keys
    u32RegisterUnlockKey = 0x5ecacce5;
    u32RegisterLockKey   = 0xa135331a;
    
    ReportStat2Value();
    
    _GetAndClearStickyError();
    
    // Check if security is enabled at all
    u32SccfgStat2Value = _ReadViaApb(u32SccfgStat2AddressApb);
    if((u32SccfgStat2Value & 0x1) == 0)
    {
        cError = 0;
        Report("--- FSEU script --- OK: MCU is unsecured");
    }
    else
    {
        // Unlock SCCFG registers
        _WriteViaApb(u32SccfgUnlckAddressApb, u32RegisterUnlockKey);

        // Enter security key
        _WriteViaApb(u32SccfgSeckey0AddressApb      , u32KeyBytes0_3);
        _WriteViaApb(u32SccfgSeckey0AddressApb + 0x4, u32KeyBytes4_7);
        _WriteViaApb(u32SccfgSeckey0AddressApb + 0x8, u32KeyBytes8_11);
        _WriteViaApb(u32SccfgSeckey0AddressApb + 0xc, u32KeyBytes12_15);

        // Lock SCCFG registers again
        _WriteViaApb(u32SccfgUnlckAddressApb, u32RegisterLockKey);
        
        // Read SCCFG_STAT2 and SCCFG_GPREG1 to check for success
        u32SccfgStat2Value  = _ReadViaApb(u32SccfgStat2AddressApb);
        u32SccfgGpreg1Value = _ReadViaApb(u32SccfgGpreg1AddressApb);

        if(_GetAndClearStickyError() != 0)
        {
           cError = 1;
           Report("--- FSEU script --- ERROR: Trying to unlock the MCU caused the StickyError flag to be set!");
        }
        else if((u32SccfgStat2Value & 0xff) == 0x03)
        {
            cError = 1;
            Report("--- FSEU script --- ERROR: Invalid security key entered!");
        }
        else if((u32SccfgStat2Value & 0xff) == 0x01) // This SCCFG_STAT2 value is ambiguous...
        {
            // SCCFG_GPREG1 contains further BootROM status information (if not overwritten by user application)
            
            // Check if both primary and secondary configurations of Main Security Description Record are invalid
            if((u32SccfgGpreg1Value & 0x70000000) == 0x50000000)
            {
                cError = 1;
                Report("--- FSEU script --- ERROR: Invalid Main Security Description Record!");
            }
            else
            {
                cError = 0;
                Report("--- FSEU script --- OK: Correct security key entered, MCU unlocked");
            }
        }
        else // is probably never reached
        {
            cError = 1;
            Report("--- FSEU script --- ERROR: Device still secured");
        }
        
        ReportStat2Value();
        ReportGpreg1Value();
    }

    return cError;
}


/*********************************************************************
*
*  WaitForDebugReady
*
*  Waits until the BootROM has set the DBGRDY bit in SCCFG_STAT2
*  that indicates the point of time when security has been evaluated
*  (if a key has already been entered) or for an unsecured device it
*  indicates that all busses (APB, AHB) can now be fully accessed.
*
*  Return value:
*  - cError:    0 if SCCFG_STAT2_DBGRDY could be read and is set
*               otherwise 1
*/
char WaitForDebugReady(void)
{
    unsigned int u32TimeOut;
    unsigned int u32SccfgStat2AddressApb;
    unsigned int u32SccfgStat2Value;
    char cError;
    char cBreak;
    
    cError = 0;

    // Addresses as required for access via APB-AP
    u32SccfgStat2AddressApb = 0x0000f180;
    
    u32TimeOut = 10000;
    cBreak = 0;
    while(cBreak == 0)
    {
        u32TimeOut -= 1;
        
        u32SccfgStat2Value = _ReadViaApb(u32SccfgStat2AddressApb);
        
        if(_GetAndClearStickyError() == 1)
        {
            cBreak = 1;
            cError = 1;
            Report("--- FSEU script --- ERROR: Reading SCCFG_STAT2 caused the StickyError flag to be set!");
        }
        else if ((u32SccfgStat2Value & 0x100) != 0) // Check for SCCFG_STAT2_DBGRDY
        {
            cBreak = 1;
            cError = 0;
            Report("--- FSEU script --- OK: SCCFG_STAT2_DBGRDY is set, whole MCU can now be accessed (if unsecured))");
        }
        else if (u32TimeOut == 0)
        {
            cBreak = 1;
            cError = 1;
            Report("--- FSEU script --- ERROR: Canceled waiting for SCCFG_STAT2_DBGRDY (time-out reached)!");
        }
    }
    
    return cError;
}


/*********************************************************************
*
*  HaltCore
*
*  Sets a request to halt the core (enter debug state) by setting
*  core debug register DRCR bit 0 and checks if halted by reading
*  the corresponding status register
*
*  Return value:
*  - cError:    0 if Core Halt Request was successful otherwise 1
*/
char HaltCore(void)
{
    char cError;
    char cBreak;
    unsigned int u32TimeOut;
    unsigned int u32ReadData;
    unsigned int u32LockAccessRegisterAddressApb;
    unsigned int u32DebugRunControlRegisterAddressApb;
    unsigned int u32DebugStatusControlRegisterAddressApb;
    unsigned int u32UnlockKey;
    unsigned int u32LockKey;
    
    cError = 0;
    
    // Addresses as required for access via APB-AP
    u32LockAccessRegisterAddressApb         = 0x00001fb0;
    u32DebugRunControlRegisterAddressApb    = 0x00001090;
    u32DebugStatusControlRegisterAddressApb = 0x00001088;

    // Core Debug Register Unlock Key
    u32UnlockKey = 0xc5acce55;
    u32LockKey   = 0x00000000;

    _GetAndClearStickyError();
    
    // Unlock debug registers
    _WriteViaApb(u32LockAccessRegisterAddressApb, u32UnlockKey);
    // Set Halt Request
    _WriteViaApb(u32DebugRunControlRegisterAddressApb, 0x00000001);
    // Lock debug registers again
    _WriteViaApb(u32LockAccessRegisterAddressApb, u32LockKey);
    
    if(_GetAndClearStickyError() != 0)
    {
        cError = 1;
        Report("--- FSEU script --- ERROR: Trying to halt the Core caused the StickyError flag to be set!");
    }
    
    // Only proceed if previous step was successful
    if(cError == 0)
    {
        _GetAndClearStickyError();
        
        // Wait until Core halted
        
        u32TimeOut = 100;
        cBreak = 0;
        while(cBreak == 0)
        {
            u32TimeOut -= 1;
            
            u32ReadData = _ReadViaApb(u32DebugStatusControlRegisterAddressApb);
            
            if(_GetAndClearStickyError() == 1)
            {
                cBreak = 1;
                cError = 1;
                Report("--- FSEU script --- ERROR: Reading Debug Status & Control register caused the StickyError flag to be set!");
            }
            else if ((u32ReadData & 0x1) != 0) // Check if core is halted
            {
                cBreak = 1;
                cError = 0;
                Report("--- FSEU script --- OK: Core is halted now");
            }
            else if (u32TimeOut == 0)
            {
                cBreak = 1;
                cError = 1;
                Report("--- FSEU script --- ERROR: Core could not be halted (time-out reached)!");
            }
        }
    }
    
    return cError;
}


/*********************************************************************
*
*  DisableWatchdog
*
*  Disables Watchdog permanently (WDG_CFG_WD_EN_RUN = 0  and  
*  WDG_CFG_WD_EN_PSS = 0) or only in debug state (WDG_CFG_DEBUG_EN = 1)
*  depending on the specified parameter.
*  Afterwards the Watchdog configuration is locked (WDG_CFG_LOCK = 1)
*
*  Parameter:
*  - cOnlyInDebugState:   0: Disable WDG permanently
*                         1 (or other): Disable WDG only in debug (break) state
*
*  Return value:
*  - cError:    0 if WDG configuration was successful otherwise 1
*/
char DisableWatchdog(char cOnlyInDebugState)
{
    char cError;
    unsigned int u32RegisterProtectionKey;
    unsigned int u32WdgCfgBeforeConfiguration;
    unsigned int u32WdgCfgAfterConfiguration;
    unsigned int u32WdgProtAddressAhb;
    unsigned int u32WdgCfgAddressAhb;
    unsigned int u32WdgCfgRegisterValue;
    
    cError = 0;

    // WDG register addresses (AHB)
    u32WdgProtAddressAhb = 0xb0608000;
    u32WdgCfgAddressAhb  = 0xb0608048;

    // WDG register protection key
    u32RegisterProtectionKey = 0xedacce55;

    // Read - modify - write WDG_CFG register
    _GetAndClearStickyError();
    u32WdgCfgBeforeConfiguration = _ReadViaAhb(u32WdgCfgAddressAhb);
    
    if(0 == cOnlyInDebugState)
    {                           //              Clear WD_EN_RUN, WD_EN_PSS      Set LOCK
        u32WdgCfgRegisterValue = (u32WdgCfgBeforeConfiguration & 0xfffffffc) | 0x01000000;
    }
    else
    {                                                    // Set LOCK and DEBUG_EN
        u32WdgCfgRegisterValue = u32WdgCfgBeforeConfiguration | 0x01000008;
    }

    _WriteViaAhb(u32WdgProtAddressAhb, u32RegisterProtectionKey);
    _WriteViaAhb(u32WdgCfgAddressAhb, u32WdgCfgRegisterValue);

    u32WdgCfgAfterConfiguration = _ReadViaAhb(u32WdgCfgAddressAhb);
    
    if(_GetAndClearStickyError() != 0)
    {
        cError = 1;
        Report("--- FSEU script --- ERROR: Accessing Watchdog registers caused the StickyError flag to be set!");
    }
    else if(u32WdgCfgAfterConfiguration != u32WdgCfgRegisterValue)
    {
        cError = 1;
        Report("--- FSEU script --- ERROR: Watchdog configuration could not be changed!");
    }
    else
    {
        cError = 0;
        Report("--- FSEU script --- OK: Watchdog configured");
    }
    
    // Debug
    // Report1("WDG_CFG before change: ", u32WdgCfgBeforeConfiguration);
    // Report1("WDG_CFG after change: ",  u32WdgCfgAfterConfiguration);

    return cError;
}


/*********************************************************************
*
*  SetSysRamWaitCycles
*
*  Write SYSRAM read/wait cycles to 0 (for debugging from SYSRAM) to
*  prevent changing of wait cycles during code execution from SYSRAM
*
*  Return value:
*  - cError:    0 if it was successful otherwise 1
*/
char SetSysRamWaitCycles(void)
{
    char cError;
    unsigned int u32RegisterUnlockKey;
    unsigned int u32RegisterLockKey;
    unsigned int u32SrcfgCfg0AfterConfiguration;
    unsigned int u32SrcfgCfg0AddressAhb;
    unsigned int u32SrcfgKeyAddressAhb;
    
    cError = 0;

    // SRCFG register addresses (AHB)
    u32SrcfgCfg0AddressAhb = 0xb0d00000;
    u32SrcfgKeyAddressAhb  = 0xb0d0000c;

    // SRCFG register lock/unlock key
    u32RegisterUnlockKey = 0x5ecc551f;
    u32RegisterLockKey   = 0x551fb10c;

    _GetAndClearStickyError();
    
    _WriteViaAhb(u32SrcfgKeyAddressAhb, u32RegisterUnlockKey); // Unlock SRCFG registers
    _WriteViaAhb(u32SrcfgCfg0AddressAhb, 0x00000000);          // Set 0 to RDWAIT and WRWAIT in SRCFG
    _WriteViaAhb(u32SrcfgKeyAddressAhb, u32RegisterLockKey);   // Lock SRCFG registers again

    u32SrcfgCfg0AfterConfiguration = _ReadViaAhb(u32SrcfgCfg0AddressAhb); // Read back
        
    if(_GetAndClearStickyError() != 0)
    {
        cError = 1;
        Report("--- FSEU script --- ERROR: Trying to change System RAM wait cycles caused the StickyError flag to be set!");
    }
    else if((u32SrcfgCfg0AfterConfiguration & 0x03030000) == 0)
    {
        cError = 0;
        Report("--- FSEU script --- OK: System RAM wait cycles changed");
    }
    else
    {
        cError = 1;
        Report("--- FSEU script --- ERROR: System RAM wait cycles could not be changed!");
    }
    
    // Debug
    // Report1("SRCFG_CFG0 after change: ",  u32SrcfgCfg0AfterConfiguration);

    return cError;
}


/*********************************************************************
*
*  ExecuteInitSequence
*
*  Executes the functions in the correct order that are required after
*  every reset. 
*/
void ExecuteInitSequence(void)
{
    GetId();
    
    WaitForDebugReady();
    
    // Pass the security key here if the MCU is secured, otherwise key values are "don't care"
    UnlockDevice(0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff);

    HaltCore();
    
    DisableWatchdog(0);
    
    SetSysRamWaitCycles(); // only required if "debug_sysram" build configuration is selected
}





// ###################################################################
//  S E G G E R   C A L L B A C K   F U N C T I O N S
// ###################################################################

/*********************************************************************
*
*  ResetTarget
*
*  Standard/Pre-defined SEGGER function that replaces
*  the reset functionality of the DLL/J-Link.
*/
void ResetTarget(void)
{
    Report("--- FSEU script --- ResetTarget() from JLinkScript is executed");
    
    ResetMcu(1);
    
    // Adaption to customer hardware may be required
    SYS_Sleep(300); // Mandatory only for starterkit SK-MB9EF120-001, can be removed if used with other FSEU starterkits
    
    ExecuteInitSequence();
}



/*********************************************************************
*
*  InitTarget
*
*  Standard/Pre-defined SEGGER function that replaces the auto-detection
*  capability of J-Link and allows to setup custom initialisation commands
*/
void InitTarget(void)
{
    //--------------------------------------------------------------------------------------------------
    JTAG_Speed         = 1000;
    JTAG_DRPre         = 0;         // Number of devices closer to TDO than the device J-Link talks to
    JTAG_DRPost        = 0;         // Number of devices closer to TDI than the device J-Link talks to
    JTAG_IRPre         = 0;         // Total IRLen of all devices which are closer to TDO than the device J-Link talks to
    JTAG_IRPost        = 0;         // Total IRLen of all devices which are closer to TDI than the device J-Link talks to
    JTAG_IRLen         = 4;         // IRLen of Cortex-R4
    CPU                = CORTEX_R4; // It is a Cortex-R4 core
    JTAG_AllowTAPReset = 1;         // En-/Disables auto-JTAG-detection of J-Link. Has to be disabled for 
                                    // devices which need some special init which is lost at a TAP reset.
                                    // Allowed values
                                    // - 0: Auto-detection is enabled.
                                    // - 1: Auto-detection is disabled.
    //--------------------------------------------------------------------------------------------------

    Report("--- FSEU script --- InitTarget() from JLinkScript is executed");
    
    //--------------------------------------------------------------------------------------------------
    // Following function is the correct reset flow, but it cannot be executed yet together with IAR
    // because pressing the reset button in IAR IDE will call both callbacks InitTarget() and ResetTarget()
    // which is a wrong behaviour and will be fixed by Segger in future J-Link driver version.
    // Problem occurs because InitTarget() would then assert a JTAG reset that destroys all debug settings
    //
    // ResetAllAndSetDebuggerConnectedFlag();
    //
    // Temporary workaround:     
    JTAG_WriteClocks(20);
    ResetMcu(1);
    //--------------------------------------------------------------------------------------------------
    
    // Adaption to customer hardware may be required
    SYS_Sleep(300); // Mandatory only for starterkit SK-MB9EF120-001, can be removed if used with other FSEU starterkits

    PowerUpDebugPort();
    InitAccessPorts();

    ExecuteInitSequence();
}