sdk-debuger-jlink/Devices/Broadcom/BCM43907.JLinkScript

/*********************************************************************
*            (c) 1995 - 2018 SEGGER Microcontroller GmbH             *
*                        The Embedded Experts                        *
*                           www.segger.com                           *
**********************************************************************

-------------------------- END-OF-HEADER -----------------------------

File    : BCM43907.JLinkScript
Purpose : Handle reset for Broadcom BCM43907 series
Literature:
  [1]  J-Link User Guide

Additional information:
  For more information about public functions that can be implemented in order to customize J-Link actions, please refer to [1]
*/

/*********************************************************************
*
*       Constants (similar to defines)
*
**********************************************************************
*/

//
// User-specified constants to be used by PCode
//
__constant U32 _DBG_REG_VCR         = 0x007;      // Vector Catch Register
__constant U32 _DBG_REG_PRCR        = 0x0C4;      // Device Power-down and Reset Control Register
__constant U32 _DBG_REG_PRSR        = 0x0C5;      // Device Power-down and Reset Status Register
__constant U32 _DBG_REG_LOCKACCESS  = 0x3EC;
__constant U32 _DBG_REG_LOCKSTATUS  = 0x3ED;
__constant U32 _ACTIVATION_KEY      = 0xC5ACCE55;
__constant U32 _DBG_REG_DSCR        = 0x022;      // Debug Status and Control Register
__constant U32 _DBG_REG_DRCR        = 0x024;      // Debug Run Control Register

/*********************************************************************
*
*       ResetTarget
*/
void ResetTarget(void) {
  int Ctrl;
  int v;
  int BaseAddr;

  BaseAddr = 0x80001000;
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_DP_REG_SELECT, 0, (0 << 24) | (0 << 4));  // Select AP[0], bank 0
  Ctrl =  0
       | (2 << 0)    // AP-access size. Fixed to 2: 32-bit
       | (0 << 4)    // Auto increment TAR after read/write access. Increment is NOT performed on access to banked data registers 0-3.
       | (1 << 31)   // Enable software access to the Debug APB bus.
       ;
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_CTRL, 1, Ctrl);  
  //
  // Prepare CPU to be halted immediately after reset (vector catch)
  //
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_VCR << 2));          // DBG_REG_VCR
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_DATA, 1, 1);                                // Set reset vector catch
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_PRCR << 2));          // DBG_REG_PRCR
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_DATA, 1, 1);                                // Make sure that device is not held in reset
  //
  // Reset CPU by toggling reset pin
  // Wait some time after reset release to give pin some time to get HIGH
  // and to give ROM BTL of SAMA5 some time to finish its work and enable debug access
  //
  JLINK_JTAG_ResetPin = 0;
  JLINK_SYS_Sleep(100);
  JLINK_JTAG_ResetPin = 1;
  JLINK_SYS_Sleep(100);
  //
  // Check if CPU is halted. If not, halt it.
  // Select & setup APB-AP
  //
  Report("J-Link script: Reset");
  JTAG_Write(0x1F, 0, 6);                                                            // Perform TAP reset
  v = (1 << 1) | (1 << 30) | (1 << 28);                                              // Request power-up on debug and system port, Make sure that sticky overrun bit gets cleared
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_DP_REG_CTRL_STAT, 0, v);
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_DP_REG_SELECT, 0, (0 << 24) | (0 << 4));  // Select AP[0], bank 0
  Ctrl =  0
       | (2 << 0)    // AP-access size. Fixed to 2: 32-bit
       | (0 << 4)    // Auto increment TAR after read/write access. Increment is NOT performed on access to banked data registers 0-3.
       | (1 << 31)   // Enable software access to the Debug APB bus.
       ;
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_CTRL, 1, Ctrl);
  //
  // Init debug logic
  //
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_LOCKACCESS << 2));
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_DATA, 1, _ACTIVATION_KEY);                        // Unlock access to the debug registers
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_LOCKSTATUS << 2));
  v = JLINK_CORESIGHT_ReadAP(JLINK_CORESIGHT_AP_REG_DATA);
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_PRCR << 2));
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_DATA, 1, 0x1);                                    // Disable power-down mode
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_PRSR << 2));
  v = JLINK_CORESIGHT_ReadAP(JLINK_CORESIGHT_AP_REG_DATA);
  //
  // Read DSCR to check if CPU is halted and halt it, if necessary
  //
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_DSCR << 2));
  v = JLINK_CORESIGHT_ReadAP(JLINK_CORESIGHT_AP_REG_DATA);
  v = JLINK_CORESIGHT_ReadAP(JLINK_CORESIGHT_AP_REG_DATA);
  if ((v & 1) == 0) {
    JLINK_SYS_Report("J-Link script: Core did not halt after reset. Halting core...");
    v |= (1 << 14);
    JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_DSCR << 2));   // Enable debug halt mode by writing the DSCR
    JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_DATA, 1, v);
    JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_DRCR << 2));   // Write DRCR to halt CPU
    JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_DATA, 1, 1);
    v = JLINK_CORESIGHT_ReadAP(JLINK_CORESIGHT_AP_REG_DATA);                                     // Write to AP may be delayed until next read/write, so perform a dummy read
  }
  //
  // Clear vector catch
  //
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_ADDR, 1, BaseAddr + (_DBG_REG_VCR << 2));
  JLINK_CORESIGHT_WriteDAP(JLINK_CORESIGHT_AP_REG_DATA, 1, 0);
  Report("J-Link script: Done");
}