menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_ETH
        bool "Enable Ethernet"
        select RT_USING_LWIP
        default n

        if BSP_USING_ETH
            choice
                prompt "On-board PHY chip"
                default PHY_USING_DP83848C

                config PHY_USING_DP83848C
                    bool "DP83848C"

                config PHY_USING_LAN8720A
                    bool "LAN8720A"

                config PHY_USING_DM9161CEP
                    bool "DM9161CEP"

            endchoice
        endif

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_STM32_UART_V1_TX_TIMEOUT
                int "UART TX timeout"
                default 4000
                depends on RT_USING_SERIAL_V1
                
            menuconfig BSP_USING_UART1
                bool "Enable UART1"
                default y
                if BSP_USING_UART1
                    config BSP_UART1_RX_USING_DMA
                        bool "Enable UART1 RX DMA"
                        depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART1_TX_USING_DMA
                        bool "Enable UART1 TX DMA"
                        depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART1_RX_BUFSIZE
                        int "Set UART1 RX buffer size"
                        range 64 65535
                        depends on RT_USING_SERIAL_V2
                        default 256

                    config BSP_UART1_TX_BUFSIZE
                        int "Set UART1 TX buffer size"
                        range 0 65535
                        depends on RT_USING_SERIAL_V2
                        default 0

                    config BSP_UART1_DMA_PING_BUFSIZE
                        int "Set UART1 RX DMA ping-pong buffer size"
                        range 32 65535
                        depends on RT_USING_SERIAL_V2 && BSP_UART1_RX_USING_DMA
                        default 64    
                endif

            menuconfig BSP_USING_UART5
                bool "Enable UART5"
                default n
                if BSP_USING_UART5
                    config BSP_UART5_RX_USING_DMA
                        bool "Enable UART5 RX DMA"
                        select RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART5_TX_USING_DMA
                        bool "Enable UART5 TX DMA"
                        select RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART5_RX_BUFSIZE
                        int "Set UART5 RX buffer size"
                        range 64 65535
                        depends on BSP_USING_UART5
                        default 256

                    config BSP_UART5_TX_BUFSIZE
                        int "Set UART5 TX buffer size"
                        range 0 65535
                        depends on BSP_USING_UART5
                        default 0

                    config BSP_UART5_DMA_PING_BUFSIZE
                        int "Set UART5 RX DMA ping-pong buffer size"
                        range 32 65535
                        depends on RT_USING_SERIAL_V2 && BSP_UART5_RX_USING_DMA
                        default 64                        
                endif
        endif

    source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu