张康 596468e4bc release rt-thread v4.1.1 2 лет назад
..
applications 596468e4bc release rt-thread v4.1.1 2 лет назад
board 596468e4bc release rt-thread v4.1.1 2 лет назад
linking_scripts 27740d4d79 release rt-thread v4.1.0 3 лет назад
.config 596468e4bc release rt-thread v4.1.1 2 лет назад
Kconfig 27740d4d79 release rt-thread v4.1.0 3 лет назад
Nu_Link_Driver.ini 27740d4d79 release rt-thread v4.1.0 3 лет назад
README.md 27740d4d79 release rt-thread v4.1.0 3 лет назад
SConscript 27740d4d79 release rt-thread v4.1.0 3 лет назад
SConstruct 596468e4bc release rt-thread v4.1.1 2 лет назад
config_lvgl 596468e4bc release rt-thread v4.1.1 2 лет назад
project.uvprojx 596468e4bc release rt-thread v4.1.1 2 лет назад
rtconfig.h 596468e4bc release rt-thread v4.1.1 2 лет назад
rtconfig.py 596468e4bc release rt-thread v4.1.1 2 лет назад
template.ewd 27740d4d79 release rt-thread v4.1.0 3 лет назад
template.ewp 27740d4d79 release rt-thread v4.1.0 3 лет назад
template.eww 27740d4d79 release rt-thread v4.1.0 3 лет назад
template.uvprojx 27740d4d79 release rt-thread v4.1.0 3 лет назад

README.md

NuMaker-M2354

1. Introduction

The NuMaker-M2354 is an evaluation board for Nuvoton NuMicro M2354 microcontrollers. The NuMaker-M2354 consists of two parts, a M2354 target board and an on-board Nu-Link2-Me debugger and programmer. The NuMaker-M2354 is designed for secure evaluation, prototype development and validation with power consumption monitoring function.

NuMaker-M2354

1.1 MCU specification

| | Features | | -- | -- | | MCU | M2354KJFAE | | Operation frequency | 96MHz | | embedded Flash size | 1MB, Dual Bank | | SRAM size | 256kB | | Crypto engine | PRNG, AES, ECC, RSA, HMAC and SHA crypto accelerator |

1.2 Interface

| Interface | | -- | | Arduino UNO | | USB 1.1 OTG ports | | A microSD slot | | A segment LCD port |

1.3 On-board devices

| Device | Description | Driver supporting status | | -- | -- | -- | |Wi-Fi module| ESP8266-ESP12, AT firmware v1.7 | Supported | |Segment LCD module| | Supported |

2. Supported compiler

Support GCC, MDK5, IAR IDE/compilers. More information of these compiler version as following:

IDE/Compiler Tested version
MDK5 5.26.2
IAR 8.32
GCC GCC 6.3.1 20170620 (Need update env)

Notice: (1) Please install Nu-Link_Keil_Driver or Nu-Link_IAR_Driver for development.

3. Program firmware

Step 1:

At first, you need to configure ISW1 switch on the NuMaker-M2354 board. Set the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-M2354 board and your computer using the USB Micro cable. After that, window manager will show a ‘NuMicro MCU’ virtual disk. Finally, you will use this virtual disk to burn firmware.

NuLinkMe

NuMicro MCU

Step 2:

A simple firmware burning method is that you can drag and drop the binary image file to NuMicro MCU virtual disk or copy the binary file to NuMicro MCU disk to burn firmware.

CopyTo

4. Test

You can use Tera Term terminate emulator (or other software) to type commands of RTT. All parameters of serial communication are shown in below image. Here, you can find out the corresponding port number of Nuvoton Virtual Com Port in window device manager.

Serial settings

5. Purchase

6. Resources