|
|
@@ -1,405 +1,385 @@
|
|
|
-ESP-WROVER-KIT V3 Getting Started Guide (CMake)
|
|
|
-===============================================
|
|
|
-
|
|
|
-This user guide shows how to get started with ESP-WROVER-KIT V3 development board including description of its functionality and configuration options. For description of other versions of the ESP-WROVER-KIT check :doc:`../hw-reference/index`.
|
|
|
-
|
|
|
-
|
|
|
-What You Need
|
|
|
--------------
|
|
|
-
|
|
|
-* 1 × :ref:`ESP-WROVER-KIT V3 board <get-started-esp-wrover-kit-board-front-cmake>`
|
|
|
-* 1 x Micro USB 2.0 Cable, Type A to Micro B
|
|
|
-* 1 × PC loaded with Windows, Linux or Mac OS
|
|
|
-
|
|
|
-If you want to start using this board right now, go directly to Section `Start Application Development`_.
|
|
|
-
|
|
|
-
|
|
|
-Overview
|
|
|
-^^^^^^^^
|
|
|
-
|
|
|
-The ESP-WROVER-KIT is a development board produced by `Espressif <https://espressif.com>`_ built around ESP32. This board is compatible with ESP32 modules, including the ESP-WROOM-32 and ESP32-WROVER. The ESP-WROVER-KIT features support for an LCD and MicroSD card. The I/O pins have been broken out from the ESP32 module for easy extension. The board carries an advanced multi-protocol USB bridge (the FTDI FT2232HL), enabling developers to use JTAG directly to debug the ESP32 through the USB interface. The development board makes secondary development easy and cost-effective.
|
|
|
-
|
|
|
-.. note::
|
|
|
-
|
|
|
- ESP-WROVER-KIT V3 integrates the ESP32-WROVER module by default.
|
|
|
-
|
|
|
-
|
|
|
-Functionality Overview
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-Block diagram below presents main components of ESP-WROVER-KIT and interconnections between components.
|
|
|
-
|
|
|
-.. figure:: ../../_static/esp-wrover-kit-block-diagram.png
|
|
|
- :align: center
|
|
|
- :alt: ESP-WROVER-KIT block diagram
|
|
|
- :figclass: align-center
|
|
|
-
|
|
|
- ESP-WROVER-KIT block diagram
|
|
|
-
|
|
|
-
|
|
|
-Functional Description
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-The following list and figures below describe key components, interfaces and controls of ESP-WROVER-KIT board.
|
|
|
-
|
|
|
-32.768 kHz
|
|
|
- An external precision 32.768 kHz crystal oscillator provides the chip with a clock of low-power consumption during the Deep-sleep mode.
|
|
|
-0R
|
|
|
- A zero Ohm resistor intended as a placeholder for a current shunt. May be desoldered or replaced with a current shunt to facilitate measurement of current required by ESP32 module depending on power mode.
|
|
|
-ESP32 Module
|
|
|
- ESP-WROVER-KIT is compatible with both ESP-WROOM-32 and ESP32-WROVER. The ESP32-WROVER module features all the functions of ESP-WROOM-32 and integrates an external 32-MBit PSRAM for flexible extended storage and data processing capabilities.
|
|
|
-
|
|
|
- .. note::
|
|
|
-
|
|
|
- GPIO16 and GPIO17 are used as the CS and clock signal for PSRAM. To ensure reliable performance, the two GPIOs are not broken out.
|
|
|
-
|
|
|
-FT2232
|
|
|
- The FT2232 chip is a multi-protocol USB-to-serial bridge. Users can control and program the FT2232 chip through the USB interface to establish communication with ESP32. The FT2232 chip also features USB-to-JTAG interface. USB-to-JTAG is available on channel A of FT2232, USB-to-serial on channel B. The embedded FT2232 chip is one of the distinguishing features of the ESPWROVER-KIT. It enhances users’ convenience in terms of application development and debugging. In addition, users do not need to buy a JTAG debugger separately, which reduces the development cost, see `ESP-WROVER-KIT V3 schematic`_.
|
|
|
-UART
|
|
|
- Serial port: the serial TX/RX signals on FT2232HL and ESP32 are broken out to the two sides of JP11. By default, the two signals are connected with jumpers. To use the ESP32 module serial interface only, the jumpers may be removed and the module can be connected to another external serial device.
|
|
|
-SPI
|
|
|
- SPI interface: the SPI interface connects to an external flash (PSRAM). To interface another SPI device, an extra CS signal is needed. The electrical level on the flash of this module is 1.8V. If an ESP-WROOM-32 is being used, please note that the electrical level on the flash of this module is 3.3V.
|
|
|
-CTS/RTS
|
|
|
- Serial port flow control signals: the pins are not connected to the circuitry by default. To enable them, respective pins of JP14 must be shorted with jumpers.
|
|
|
-JTAG
|
|
|
- JTAG interface: the JTAG signals on FT2232HL and ESP32 are broken out to the two sides of JP8. By default, the two signals are disconnected. To enable JTAG, shorting jumpers are required on the signals.
|
|
|
-EN
|
|
|
- Reset button: pressing this button resets the system.
|
|
|
-Boot
|
|
|
- Download button: holding down the **Boot** button and pressing the **EN** button initiates the firmware download mode. Then user can download firmware through the serial port.
|
|
|
-USB
|
|
|
- USB interface. It functions as the power supply for the board and the communication interface between PC and ESP32 module.
|
|
|
-Power Select
|
|
|
- Power supply selection interface: the ESP-WROVER-KIT can be powered through the USB interface or the 5V Input interface. The user can select the power supply with a jumper. More details can be found in Section :ref:`get-started-esp-wrover-kit-setup-options-cmake`, jumper header JP7.
|
|
|
-Power Key
|
|
|
- Power on/off button: toggling to the right powers the board on; toggling to the left powers the board off.
|
|
|
-5V Input
|
|
|
- The 5V power supply interface is used as a backup power supply in case of full-load operation.
|
|
|
-LDO
|
|
|
- NCP1117(1A). 5V-to-3.3V LDO. (There is an alternative pin-compatible LDO — LM317DCY, with an output current of up to 1.5A). NCP1117 can provide a maximum current of 1A. The LDO solutions are available with both fixed output voltage and variable output voltage. For details please refer to `ESP-WROVER-KIT V3 schematic`_.
|
|
|
-Camera
|
|
|
- Camera interface: a standard OV7670 camera module is supported.
|
|
|
-RGB
|
|
|
- Red, green and blue (RGB) light emitting diodes (LEDs), which may be controlled by pulse width modulation (PWM).
|
|
|
-I/O
|
|
|
- All the pins on the ESP32 module are led out to the pin headers on the ESP-WROVER-KIT. Users can program ESP32 to enable multiple functions such as PWM, ADC, DAC, I2C, I2S, SPI, etc.
|
|
|
-Micro SD Card
|
|
|
- Micro SD card slot for data storage.
|
|
|
-LCD
|
|
|
- ESP-WROVER-KIT supports mounting and interfacing a 3.2” SPI (standard 4-wire Serial Peripheral Interface) LCD, as shown on figure :ref:`get-started-esp-wrover-kit-board-back-cmake`.
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-kit-board-front-cmake:
|
|
|
-
|
|
|
-.. figure:: ../../_static/esp32-wrover-kit-layout-front.jpg
|
|
|
- :align: center
|
|
|
- :alt: ESP-WROVER-KIT board layout - front
|
|
|
- :figclass: align-center
|
|
|
-
|
|
|
- ESP-WROVER-KIT board layout - front
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-kit-board-back-cmake:
|
|
|
-
|
|
|
-.. figure:: ../../_static/esp32-wrover-kit-layout-back.jpg
|
|
|
- :align: center
|
|
|
- :alt: ESP-WROVER-KIT board layout - back
|
|
|
- :figclass: align-center
|
|
|
-
|
|
|
- ESP-WROVER-KIT board layout - back
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-kit-setup-options-cmake:
|
|
|
-
|
|
|
-Setup Options
|
|
|
-^^^^^^^^^^^^^
|
|
|
-
|
|
|
-There are five jumper headers available to set up the board functionality. Typical options to select from are listed in table below.
|
|
|
-
|
|
|
-+--------+------------------+--------------------------------------------------+
|
|
|
-| Header | Jumper Setting | Description of Functionality |
|
|
|
-+--------+------------------+--------------------------------------------------+
|
|
|
-| JP7 | |jp7-ext_5v| | Power ESP-WROVER-KIT board from an external |
|
|
|
-| | | power supply |
|
|
|
-+--------+------------------+--------------------------------------------------+
|
|
|
-| JP7 | |jp7-usb_5v| | Power ESP-WROVER-KIT board from an USB port |
|
|
|
-+--------+------------------+--------------------------------------------------+
|
|
|
-| JP8 | |jp8| | Enable JTAG functionality |
|
|
|
-+--------+------------------+--------------------------------------------------+
|
|
|
-| JP11 | |jp11-rx-tx| | Enable UART communication |
|
|
|
-+--------+------------------+--------------------------------------------------+
|
|
|
-| JP14 | |jp14| | Enable RTS/CTS flow control for serial |
|
|
|
-| | | communication |
|
|
|
-+--------+------------------+--------------------------------------------------+
|
|
|
-
|
|
|
-
|
|
|
-Allocation of ESP32 Pins
|
|
|
-^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-Several pins / terminals of ESP32 module are allocated to the on board hardware. Some of them, like GPIO0 or GPIO2, have multiple functions. If certain hardware is not installed, e.g. nothing is plugged in to the Camera / JP4 header, then selected GPIOs may be used for other purposes.
|
|
|
-
|
|
|
-
|
|
|
-Main I/O Connector / JP1
|
|
|
-""""""""""""""""""""""""
|
|
|
-
|
|
|
-The JP1 connector is shown in two columns in the middle under "I/O" headers. The two columns "Shared With" outside, describe where else on the board certain GPIO is used.
|
|
|
-
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| Shared With | I/O | I/O | Shared With |
|
|
|
-+======================+======+======+======================+
|
|
|
-| | 3.3V | GND | |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| NC/XTAL | IO32 | IO33 | NC/XTAL |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| JTAG, MicroSD | IO12 | IO13 | JTAG, MicroSD |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| JTAG, MicroSD | IO14 | IO27 | Camera |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| Camera | IO26 | IO25 | Camera, LCD |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| Camera | IO35 | IO34 | Camera |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| Camera | IO39 | IO36 | Camera |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| JTAG | EN | IO23 | Camera, LCD |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| Camera, LCD | IO22 | IO21 | Camera, LCD, MicroSD |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| Camera, LCD | IO19 | IO18 | Camera, LCD |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| Camera, LCD | IO5 | IO17 | PSRAM |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| PSRAM | IO16 | IO4 | LED, Camera, MicroSD |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| LED, Boot | IO0 | IO2 | LED, Camera, MicroSD |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-| JTAG, MicroSD | IO15 | 5V | |
|
|
|
-+----------------------+------+------+----------------------+
|
|
|
-
|
|
|
-Legend:
|
|
|
-
|
|
|
-* NC/XTAL - :ref:`32.768 kHz Oscillator <get-started-esp-wrover-kit-xtal-cmake>`
|
|
|
-* JTAG - :ref:`JTAG / JP8 <get-started-esp-wrover-jtag-header-cmake>`
|
|
|
-* Boot - Boot button / SW2
|
|
|
-* Camera - :ref:`Camera / JP4 <get-started-esp-wrover-camera-header-cmake>`
|
|
|
-* LED - :ref:`RGB LED <get-started-esp-wrover-rgb-led-connections-cmake>`
|
|
|
-* MicroSD - :ref:`MicroSD Card / J4 <get-started-esp-wrover-microsd-card-slot-cmake>`
|
|
|
-* LCD - :ref:`LCD / U5 <get-started-esp-wrover-lcd-connector-cmake>`
|
|
|
-* PSRAM - ESP32-WROVER's PSRAM, if ESP32-WROVER is installed
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-kit-xtal-cmake:
|
|
|
-
|
|
|
-32.768 kHz Oscillator
|
|
|
-"""""""""""""""""""""
|
|
|
-
|
|
|
-+---+-----------+
|
|
|
-| | ESP32 Pin |
|
|
|
-+===+===========+
|
|
|
-| 1 | GPIO32 |
|
|
|
-+---+-----------+
|
|
|
-| 2 | GPIO33 |
|
|
|
-+---+-----------+
|
|
|
-
|
|
|
-.. note::
|
|
|
-
|
|
|
- As GPIO32 and GPIO33 are connected to the oscillator, to maintain signal integrity, they are not connected to JP1 I/O expansion connector. This allocation may be changed from oscillator to JP1 by desoldering 0R resistors from positions R11 / R23 and installing them in positions R12 / R24.
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-spi-flash-header-cmake:
|
|
|
-
|
|
|
-SPI Flash / JP13
|
|
|
-""""""""""""""""
|
|
|
-
|
|
|
-+---+--------------+
|
|
|
-| | ESP32 Pin |
|
|
|
-+===+==============+
|
|
|
-| 1 | CLK / GPIO6 |
|
|
|
-+---+--------------+
|
|
|
-| 2 | SD0 / GPIO7 |
|
|
|
-+---+--------------+
|
|
|
-| 3 | SD1 / GPIO8 |
|
|
|
-+---+--------------+
|
|
|
-| 4 | SD2 / GPIO9 |
|
|
|
-+---+--------------+
|
|
|
-| 5 | SD3 / GPIO10 |
|
|
|
-+---+--------------+
|
|
|
-| 6 | CMD / GPIO11 |
|
|
|
-+---+--------------+
|
|
|
-
|
|
|
-.. important::
|
|
|
-
|
|
|
- The module's flash bus is connected to the pin header JP13 through 0-Ohm resistors R140 ~ R145. If the flash frequency needs to operate at 80 MHz, to improve integrity of the bus signals, it is recommended to desolder resistors R140 ~ R145. At this point, the module's flash bus is disconnected with the pin header JP13.
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-jtag-header-cmake:
|
|
|
-
|
|
|
-JTAG / JP8
|
|
|
-""""""""""
|
|
|
-
|
|
|
-+---+---------------+-------------+
|
|
|
-| | ESP32 Pin | JTAG Signal |
|
|
|
-+===+===============+=============+
|
|
|
-| 1 | EN | TRST_N |
|
|
|
-+---+---------------+-------------+
|
|
|
-| 2 | MTDO / GPIO15 | TDO |
|
|
|
-+---+---------------+-------------+
|
|
|
-| 3 | MTDI / GPIO12 | TDI |
|
|
|
-+---+---------------+-------------+
|
|
|
-| 4 | MTCK / GPIO13 | TCK |
|
|
|
-+---+---------------+-------------+
|
|
|
-| 5 | MTMS / GPIO14 | TMS |
|
|
|
-+---+---------------+-------------+
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-camera-header-cmake:
|
|
|
-
|
|
|
-Camera / JP4
|
|
|
-""""""""""""
|
|
|
-
|
|
|
-+----+--------------+----------------------+
|
|
|
-| | ESP32 Pin | Camera Signal |
|
|
|
-+====+==============+======================+
|
|
|
-| 1 | GPIO27 | SCCB Clock |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 2 | GPIO26 | SCCB Data |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 3 | GPIO21 | System Clock |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 4 | GPIO25 | Vertical Sync |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 5 | GPIO23 | Horizontal Reference |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 6 | GPIO22 | Pixel Clock |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 7 | GPIO4 | Pixel Data Bit 0 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 8 | GPIO5 | Pixel Data Bit 1 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 9 | GPIO18 | Pixel Data Bit 2 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 10 | GPIO19 | Pixel Data Bit 3 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 11 | GPIO36 | Pixel Data Bit 4 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 11 | GPIO39 | Pixel Data Bit 5 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 11 | GPIO34 | Pixel Data Bit 6 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 11 | GPIO35 | Pixel Data Bit 7 |
|
|
|
-+----+--------------+----------------------+
|
|
|
-| 11 | GPIO2 | Camera Reset |
|
|
|
-+----+--------------+----------------------+
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-rgb-led-connections-cmake:
|
|
|
-
|
|
|
-RGB LED
|
|
|
-"""""""
|
|
|
-
|
|
|
-+---+-----------+---------+
|
|
|
-| | ESP32 Pin | RGB LED |
|
|
|
-+===+===========+=========+
|
|
|
-| 1 | GPIO0 | Red |
|
|
|
-+---+-----------+---------+
|
|
|
-| 2 | GPIO2 | Blue |
|
|
|
-+---+-----------+---------+
|
|
|
-| 3 | GPIO4 | Green |
|
|
|
-+---+-----------+---------+
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-microsd-card-slot-cmake:
|
|
|
-
|
|
|
-MicroSD Card / J4
|
|
|
-"""""""""""""""""
|
|
|
-
|
|
|
-+---+---------------+----------------+
|
|
|
-| | ESP32 Pin | MicroSD Signal |
|
|
|
-+===+===============+================+
|
|
|
-| 1 | MTDI / GPIO12 | DATA2 |
|
|
|
-+---+---------------+----------------+
|
|
|
-| 2 | MTCK / GPIO13 | CD / DATA3 |
|
|
|
-+---+---------------+----------------+
|
|
|
-| 3 | MTDO / GPIO15 | CMD |
|
|
|
-+---+---------------+----------------+
|
|
|
-| 4 | MTMS / GPIO14 | CLK |
|
|
|
-+---+---------------+----------------+
|
|
|
-| 5 | GPIO2 | DATA0 |
|
|
|
-+---+---------------+----------------+
|
|
|
-| 6 | GPIO4 | DATA1 |
|
|
|
-+---+---------------+----------------+
|
|
|
-| 7 | GPIO21 | CD |
|
|
|
-+---+---------------+----------------+
|
|
|
-
|
|
|
-
|
|
|
-.. _get-started-esp-wrover-lcd-connector-cmake:
|
|
|
-
|
|
|
-LCD / U5
|
|
|
-""""""""
|
|
|
-
|
|
|
-+---+-----------+------------+
|
|
|
-| | ESP32 Pin | LCD Signal |
|
|
|
-+===+===========+============+
|
|
|
-| 1 | GPIO18 | RESET |
|
|
|
-+---+-----------+------------+
|
|
|
-| 2 | GPIO19 | SCL |
|
|
|
-+---+-----------+------------+
|
|
|
-| 3 | GPIO21 | D/C |
|
|
|
-+---+-----------+------------+
|
|
|
-| 4 | GPIO22 | CS |
|
|
|
-+---+-----------+------------+
|
|
|
-| 5 | GPIO23 | SDA |
|
|
|
-+---+-----------+------------+
|
|
|
-| 6 | GPIO25 | SDO |
|
|
|
-+---+-----------+------------+
|
|
|
-| 7 | GPIO5 | Backlight |
|
|
|
-+---+-----------+------------+
|
|
|
-
|
|
|
-
|
|
|
-Start Application Development
|
|
|
------------------------------
|
|
|
-
|
|
|
-Before powering up your ESP-WROVER-KIT V3, please make sure that the board is in good condition with no obvious signs of damage.
|
|
|
-
|
|
|
-
|
|
|
-Initial Setup
|
|
|
-^^^^^^^^^^^^^
|
|
|
-
|
|
|
-Select the source of power supply for the board by setting jumper JP7. The options are either USB port or an external power supply. For this application selection of USB port is sufficient. Enable UART communication by installing jumpers on JP11. Both selections are shown in table below.
|
|
|
-
|
|
|
-+----------------------+----------------------+
|
|
|
-| Power up | Enable UART |
|
|
|
-| from USB port | communication |
|
|
|
-+----------------------+----------------------+
|
|
|
-| |jp7-usb_5v| | |jp11-rx-tx| |
|
|
|
-+----------------------+----------------------+
|
|
|
-
|
|
|
-Do not install any other jumpers.
|
|
|
-
|
|
|
-
|
|
|
-Now to Development
|
|
|
-^^^^^^^^^^^^^^^^^^
|
|
|
-
|
|
|
-Please proceed to :doc:`index`, where Section :ref:`get-started-step-by-step-cmake` will quickly help you set up the development environment and then flash an example project onto your board.
|
|
|
-
|
|
|
-
|
|
|
-Related Documents
|
|
|
------------------
|
|
|
-
|
|
|
-* `ESP-WROVER-KIT V3 schematic`_ (PDF)
|
|
|
-* `ESP32 Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf>`_ (PDF)
|
|
|
-* `ESP32-WROVER Datasheet <https://espressif.com/sites/default/files/documentation/esp32-wrover_datasheet_en.pdf>`_ (PDF)
|
|
|
-* `ESP-WROOM-32 Datasheet <https://espressif.com/sites/default/files/documentation/esp-wroom-32_datasheet_en.pdf>`_ (PDF)
|
|
|
-* :doc:`../api-guides/jtag-debugging/index`
|
|
|
-* :doc:`../hw-reference/index`
|
|
|
-
|
|
|
-.. |jp7-ext_5v| image:: ../../_static/esp-wrover-kit-v3-jp7-ext_5v.png
|
|
|
-.. |jp7-usb_5v| image:: ../../_static/esp-wrover-kit-v3-jp7-usb_5v.png
|
|
|
-.. |jp8| image:: ../../_static/esp-wrover-kit-v3-jp8.png
|
|
|
-.. |jp11-rx-tx| image:: ../../_static/esp-wrover-kit-v3-jp11-tx-rx.png
|
|
|
-.. |jp14| image:: ../../_static/esp-wrover-kit-v3-jp14.png
|
|
|
-
|
|
|
-.. _ESP-WROVER-KIT V3 schematic: https://dl.espressif.com/dl/schematics/ESP-WROVER-KIT_SCH-3.pdf
|
|
|
-
|
|
|
-.. toctree::
|
|
|
- :hidden:
|
|
|
-
|
|
|
- get-started-wrover-kit-v2.rst
|
|
|
+ESP-WROVER-KIT V4.1 Getting Started Guide (CMake)
|
|
|
+=================================================
|
|
|
+:link_to_translation:`zh_CN:[中文]`
|
|
|
+
|
|
|
+This guide shows how to get started with the ESP-WROVER-KIT V4.1 development board and also provides information about its functionality and configuration options. For the description of other ESP-WROVER-KIT versions, please check :doc:`../hw-reference/index`.
|
|
|
+
|
|
|
+
|
|
|
+What You Need
|
|
|
+-------------
|
|
|
+
|
|
|
+* :ref:`ESP-WROVER-KIT V4.1 board <get-started-esp-wrover-kit-v4.1-board-front-cmake>`
|
|
|
+* USB 2.0 A to Micro B Cable
|
|
|
+* Computer running Windows, Linux, or macOS
|
|
|
+
|
|
|
+You can skip the introduction sections and go directly to Section `Start Application Development`_.
|
|
|
+
|
|
|
+
|
|
|
+Overview
|
|
|
+--------
|
|
|
+
|
|
|
+ESP-WROVER-KIT is an ESP32-based development board produced by `Espressif <https://espressif.com>`_.
|
|
|
+
|
|
|
+ESP-WROVER-KIT features the following integrated components:
|
|
|
+
|
|
|
+- ESP32-WROVER-B module
|
|
|
+- LCD screen
|
|
|
+- MicroSD card slot
|
|
|
+
|
|
|
+Its another distinguishing feature is the embedded FTDI FT2232HL chip - an advanced multi-interface USB bridge. This chip enables to use JTAG for direct debugging of ESP32 through the USB interface without a separate JTAG debugger. ESP-WROVER-KIT makes development convenient, easy, and cost-effective.
|
|
|
+
|
|
|
+Most of the ESP32 I/O pins are broken out to the board's pin headers for easy access.
|
|
|
+
|
|
|
+ .. note::
|
|
|
+
|
|
|
+ ESP32's GPIO16 and GPIO17 are used as chip select and clock signals for PSRAM. By default, the two GPIOs are not broken out to the board's pin headers in order to ensure reliable performance.
|
|
|
+
|
|
|
+
|
|
|
+Functionality Overview
|
|
|
+----------------------
|
|
|
+
|
|
|
+The block diagram below shows the main components of ESP-WROVER-KIT and their interconnections.
|
|
|
+
|
|
|
+.. figure:: ../../_static/esp-wrover-kit-block-diagram.png
|
|
|
+ :align: center
|
|
|
+ :alt: ESP-WROVER-KIT block diagram
|
|
|
+ :figclass: align-center
|
|
|
+
|
|
|
+ ESP-WROVER-KIT block diagram
|
|
|
+
|
|
|
+
|
|
|
+Functional Description
|
|
|
+----------------------
|
|
|
+
|
|
|
+The following two figures and the table below describe the key components, interfaces and controls of the ESP-WROVER-KIT board.
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-board-front-cmake:
|
|
|
+
|
|
|
+.. figure:: ../../_static/esp-wrover-kit-v4.1-layout-front.png
|
|
|
+ :align: center
|
|
|
+ :alt: ESP-WROVER-KIT board layout - front
|
|
|
+ :figclass: align-center
|
|
|
+
|
|
|
+ ESP-WROVER-KIT board layout - front
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-board-back-cmake:
|
|
|
+
|
|
|
+.. figure:: ../../_static/esp-wrover-kit-v4.1-layout-back.png
|
|
|
+ :align: center
|
|
|
+ :alt: ESP-WROVER-KIT board layout - back
|
|
|
+ :figclass: align-center
|
|
|
+
|
|
|
+ ESP-WROVER-KIT board layout - back
|
|
|
+
|
|
|
+
|
|
|
+The table below provides description in the following manner:
|
|
|
+
|
|
|
+- Starting from the first picture's top right corner and going clockwise
|
|
|
+- Then moving on to the second picture
|
|
|
+
|
|
|
+
|
|
|
+================== =================================================================================================================================
|
|
|
+Key Component Description
|
|
|
+================== =================================================================================================================================
|
|
|
+FT2232 The FT2232 chip serves as a multi-protocol USB-to-serial bridge which can be programmed and controlled via USB to provide communication with ESP32. FT2232 also features USB-to-JTAG interface which is available on channel A of the chip, while USB-to-serial is on channel B. The FT2232 chip enhances user-friendliness in terms of application development and debugging. See `ESP-WROVER-KIT V4.1 schematic`_.
|
|
|
+
|
|
|
+32.768 kHz External precision 32.768 kHz crystal oscillator serves as a clock with low-power consumption while the chip is in Deep-sleep mode.
|
|
|
+
|
|
|
+0R Zero-ohm resistor intended as a placeholder for a current shunt, can be desoldered or replaced with a current shunt to facilitate the measurement of ESP32's current consumption in different modes.
|
|
|
+
|
|
|
+ESP32-WROVER This EPS32 module features 64-Mbit PSRAM for flexible extended storage and data processing capabilities.
|
|
|
+
|
|
|
+Diagnostic LEDs Four red LEDs connected to the GPIO pins of FT2232. Intended for future use.
|
|
|
+
|
|
|
+UART Serial port. The serial TX/RX signals of FT2232 and ESP32 are broken out to the inward and outward sides of JP2 respectively. By default, these pairs of pins are connected with jumpers. To use ESP32's serial interface, remove the jumpers and connect another external serial device to the respective pins.
|
|
|
+
|
|
|
+SPI By default, ESP32 uses its SPI interface to access flash and PSRAM memory inside the module. Use these pins to connect ESP32 to another SPI device. In this case, an extra chip select (CS) signal is needed. Please note that the voltage of this interface is 3.3V.
|
|
|
+
|
|
|
+CTS/RTS Serial port flow control signals: the pins are not connected to the circuitry by default. To enable them, short the respective pins of JP14 with jumpers.
|
|
|
+
|
|
|
+JTAG JTAG interface. JTAG signals of FT2232 and ESP32 are broken out to the inward and outward sides of JP2 respectively. By default, these pairs of pins are disconnected. To enable JTAG, short the respective pins with jumpers as shown in Section `Setup Options`_.
|
|
|
+
|
|
|
+USB Port USB interface. Power supply for the board as well as the communication interface between a computer and the board.
|
|
|
+
|
|
|
+EN Button Reset button.
|
|
|
+
|
|
|
+Boot Button Download button. Holding down **Boot** and then pressing **EN** initiates Firmware Download mode for downloading firmware through the serial port.
|
|
|
+
|
|
|
+Power Switch Power On/Off Switch. Toggling toward the **Boot** button powers the board on, toggling away from **Boot** powers the board off.
|
|
|
+
|
|
|
+Power Selector Power supply selector interface. The board can be powered either via USB or via the 5V Input interface. Select the power source with a jumper. For more details, see Section `Setup Options`_, jumper header JP7.
|
|
|
+
|
|
|
+5V Input The 5V power supply interface can be more convenient when the board is operating autonomously (not connected to a computer).
|
|
|
+
|
|
|
+5V Power On LED This red LED turns on when power is supplied to the board, either from **USB** or **5V Input**.
|
|
|
+
|
|
|
+LDO NCP1117(1A). 5V-to-3.3V LDO. NCP1117 can provide a maximum current of 1A. The LDO on the board has a fixed output voltage. Although, the user can install an LDO with adjustable output voltage. For details, please refer to `ESP-WROVER-KIT V4.1 schematic`_.
|
|
|
+
|
|
|
+Camera Connector Camera interface, a standard OV7670 camera module.
|
|
|
+
|
|
|
+RGB LED Red, green and blue (RGB) light emitting diodes (LEDs), can be controlled by pulse width modulation (PWM).
|
|
|
+
|
|
|
+I/O Connector All the pins on the ESP32 module are broken out to pin headers. You can program ESP32 to enable multiple functions, such as PWM, ADC, DAC, I2C, I2S, SPI, etc.
|
|
|
+
|
|
|
+Micro SD Card Slot Useful for developing applications that access Micro SD card for data storage and retrieval.
|
|
|
+
|
|
|
+LCD Support for mounting and interfacing a 3.2” SPI (standard 4-wire Serial Peripheral Interface) LCD, as shown on figure :ref:`get-started-esp-wrover-kit-v4.1-board-back`.
|
|
|
+================== =================================================================================================================================
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-setup-options-cmake:
|
|
|
+
|
|
|
+Setup Options
|
|
|
+-------------
|
|
|
+
|
|
|
+There are three jumper blocks available to set up the board functionality. The most frequently required options are listed in the table below.
|
|
|
+
|
|
|
+======= ================ =========================================================
|
|
|
+Header Jumper Setting Description of Functionality
|
|
|
+======= ================ =========================================================
|
|
|
+JP7 |jp7-ext_5v| Power ESP-WROVER-KIT via an external power supply
|
|
|
+JP7 |jp7-usb_5v| Power ESP-WROVER-KIT via USB
|
|
|
+JP2 |jp2-jtag| Enable JTAG functionality
|
|
|
+JP2 |jp2-tx-rx| Enable UART communication
|
|
|
+JP14 |jp14| Enable RTS/CTS flow control for serial communication
|
|
|
+======= ================ =========================================================
|
|
|
+
|
|
|
+
|
|
|
+Allocation of ESP32 Pins
|
|
|
+------------------------
|
|
|
+
|
|
|
+Some pins / terminals of ESP32 are allocated for use with the onboard or external hardware. If that hardware is not used, e.g., nothing is plugged into the Camera (JP4) header, then these GPIOs can be used for other purposes.
|
|
|
+
|
|
|
+Some of the pins, such as GPIO0 or GPIO2, have multiple functions and some of them are shared among onboard and external peripheral devices. Certain combinations of peripherals cannot work together. For example, it is not possible to do JTAG debugging of an application that is using SD card, because several pins are shared by JTAG and the SD card slot.
|
|
|
+
|
|
|
+In other cases, peripherals can coexist under certain conditions. This is applicable to, for example, LCD screen and SD card that share only a single pin GPIO21. This pin is used to provide D/C (Data / Control) signal for the LCD as well as the CD (Card Detect) signal read from the SD card slot. If the card detect functionality is not essential, then it may be disabled by removing R167, so both LCD and SD may operate together.
|
|
|
+
|
|
|
+For more details on which pins are shared among which peripherals, please refer to the table in the next section.
|
|
|
+
|
|
|
+
|
|
|
+Main I/O Connector / JP1
|
|
|
+^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
+
|
|
|
+The JP1 connector consists of 14x2 male pins whose functions are shown in the middle two "I/O" columns of the table below. The two "Shared With" columns on both sides describe where else on the board a certain GPIO is used.
|
|
|
+
|
|
|
+===================== ===== ===== =====================
|
|
|
+Shared With I/O I/O Shared With
|
|
|
+===================== ===== ===== =====================
|
|
|
+n/a 3.3V GND n/a
|
|
|
+NC/XTAL IO32 IO33 NC/XTAL
|
|
|
+JTAG, MicroSD IO12 IO13 JTAG, MicroSD
|
|
|
+JTAG, MicroSD IO14 IO27 Camera
|
|
|
+Camera IO26 IO25 Camera, LCD
|
|
|
+Camera IO35 IO34 Camera
|
|
|
+Camera IO39 IO36 Camera
|
|
|
+JTAG EN IO23 Camera, LCD
|
|
|
+Camera, LCD IO22 IO21 Camera, LCD, MicroSD
|
|
|
+Camera, LCD IO19 IO18 Camera, LCD
|
|
|
+Camera, LCD IO5 IO17 PSRAM
|
|
|
+PSRAM IO16 IO4 LED, Camera, MicroSD
|
|
|
+Camera, LED, Boot IO0 IO2 LED, MicroSD
|
|
|
+JTAG, MicroSD IO15 5V
|
|
|
+===================== ===== ===== =====================
|
|
|
+
|
|
|
+Legend:
|
|
|
+
|
|
|
+* NC/XTAL - :ref:`32.768 kHz Oscillator <get-started-esp-wrover-kit-v4.1-xtal-cmake>`
|
|
|
+* JTAG - :ref:`JTAG / JP8 <get-started-esp-wrover-kit-v4.1-jtag-header-cmake>`
|
|
|
+* Boot - Boot button / SW2
|
|
|
+* Camera - :ref:`Camera / JP4 <get-started-esp-wrover-kit-v4.1-camera-header-cmake>`
|
|
|
+* LED - :ref:`RGB LED <get-started-esp-wrover-kit-v4.1-rgb-led-connections-cmake>`
|
|
|
+* MicroSD - :ref:`MicroSD Card / J4 <get-started-esp-wrover-kit-v4.1-microsd-card-slot-cmake>`
|
|
|
+* LCD - :ref:`LCD / U5 <get-started-esp-wrover-kit-v4.1-lcd-connector-cmake>`
|
|
|
+* PSRAM - ESP32-WROVER-B's PSRAM
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-xtal-cmake:
|
|
|
+
|
|
|
+32.768 kHz Oscillator
|
|
|
+^^^^^^^^^^^^^^^^^^^^^
|
|
|
+
|
|
|
+==== ==========
|
|
|
+. ESP32 Pin
|
|
|
+==== ==========
|
|
|
+1 GPIO32
|
|
|
+2 GPIO33
|
|
|
+==== ==========
|
|
|
+
|
|
|
+.. note::
|
|
|
+
|
|
|
+ Since GPIO32 and GPIO33 are connected to the oscillator by default, they are not connected to the JP1 I/O connector to maintain signal integrity. This allocation may be changed from the oscillator to JP1 by desoldering the zero-ohm resistors from positions R11 / R23 and re-soldering them to positions R12 / R24.
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-spi-flash-header-cmake:
|
|
|
+
|
|
|
+SPI Flash / JP2
|
|
|
+^^^^^^^^^^^^^^^
|
|
|
+
|
|
|
+==== =============
|
|
|
+. ESP32 Pin
|
|
|
+==== =============
|
|
|
+1 CLK / GPIO6
|
|
|
+2 SD0 / GPIO7
|
|
|
+3 SD1 / GPIO8
|
|
|
+4 SD2 / GPIO9
|
|
|
+5 SD3 / GPIO10
|
|
|
+6 CMD / GPIO11
|
|
|
+==== =============
|
|
|
+
|
|
|
+.. important::
|
|
|
+
|
|
|
+ The module's flash bus is connected to the jumper block JP2 through zero-ohm resistors R140 ~ R145. If the flash memory needs to operate at the frequency of 80 MHz, for reasons such as improving the integrity of bus signals, you can desolder these resistors to disconnect the module's flash bus from the pin header JP2.
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-jtag-header-cmake:
|
|
|
+
|
|
|
+JTAG / JP2
|
|
|
+^^^^^^^^^^
|
|
|
+
|
|
|
+==== ============== =============
|
|
|
+. ESP32 Pin JTAG Signal
|
|
|
+==== ============== =============
|
|
|
+1 EN TRST_N
|
|
|
+2 MTMS / GPIO14 TMS
|
|
|
+3 MTDO / GPIO15 TDO
|
|
|
+4 MTDI / GPIO12 TDI
|
|
|
+5 MTCK / GPIO13 TCK
|
|
|
+==== ============== =============
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-camera-header-cmake:
|
|
|
+
|
|
|
+Camera / JP4
|
|
|
+^^^^^^^^^^^^
|
|
|
+
|
|
|
+==== ========== =============================
|
|
|
+. ESP32 Pin Camera Signal
|
|
|
+==== ========== =============================
|
|
|
+ 1 n/a 3.3V
|
|
|
+ 2 n/a Ground
|
|
|
+ 3 GPIO27 SIO_C / SCCB Clock
|
|
|
+ 4 GPIO26 SIO_D / SCCB Data
|
|
|
+ 5 GPIO25 VSYNC / Vertical Sync
|
|
|
+ 6 GPIO23 HREF / Horizontal Reference
|
|
|
+ 7 GPIO22 PCLK / Pixel Clock
|
|
|
+ 8 GPIO21 XCLK / System Clock
|
|
|
+ 9 GPIO35 D7 / Pixel Data Bit 7
|
|
|
+10 GPIO34 D6 / Pixel Data Bit 6
|
|
|
+11 GPIO39 D5 / Pixel Data Bit 5
|
|
|
+12 GPIO36 D4 / Pixel Data Bit 4
|
|
|
+13 GPIO19 D3 / Pixel Data Bit 3
|
|
|
+14 GPIO18 D2 / Pixel Data Bit 2
|
|
|
+15 GPIO5 D1 / Pixel Data Bit 1
|
|
|
+16 GPIO4 D0 / Pixel Data Bit 0
|
|
|
+17 GPIO0 RESET / Camera Reset
|
|
|
+18 n/a PWDN / Camera Power Down
|
|
|
+==== ========== =============================
|
|
|
+
|
|
|
+* Signals D0 .. D7 denote camera data bus
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-rgb-led-connections-cmake:
|
|
|
+
|
|
|
+RGB LED
|
|
|
+^^^^^^^
|
|
|
+
|
|
|
+==== ========== =========
|
|
|
+. ESP32 Pin RGB LED
|
|
|
+==== ========== =========
|
|
|
+1 GPIO0 Red
|
|
|
+2 GPIO2 Green
|
|
|
+3 GPIO4 Blue
|
|
|
+==== ========== =========
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-microsd-card-slot-cmake:
|
|
|
+
|
|
|
+MicroSD Card
|
|
|
+^^^^^^^^^^^^
|
|
|
+
|
|
|
+==== ============== ===============
|
|
|
+. ESP32 Pin MicroSD Signal
|
|
|
+==== ============== ===============
|
|
|
+1 MTDI / GPIO12 DATA2
|
|
|
+2 MTCK / GPIO13 CD / DATA3
|
|
|
+3 MTDO / GPIO15 CMD
|
|
|
+4 MTMS / GPIO14 CLK
|
|
|
+5 GPIO2 DATA0
|
|
|
+6 GPIO4 DATA1
|
|
|
+7 GPIO21 CD
|
|
|
+==== ============== ===============
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-v4.1-lcd-connector-cmake:
|
|
|
+
|
|
|
+LCD / U5
|
|
|
+^^^^^^^^
|
|
|
+
|
|
|
+==== ============== ===============
|
|
|
+. ESP32 Pin LCD Signal
|
|
|
+==== ============== ===============
|
|
|
+1 GPIO18 RESET
|
|
|
+2 GPIO19 SCL
|
|
|
+3 GPIO21 D/C
|
|
|
+4 GPIO22 CS
|
|
|
+5 GPIO23 SDA
|
|
|
+6 GPIO25 SDO
|
|
|
+7 GPIO5 Backlight
|
|
|
+==== ============== ===============
|
|
|
+
|
|
|
+
|
|
|
+.. _get-started-esp-wrover-kit-start-development-cmake:
|
|
|
+
|
|
|
+Start Application Development
|
|
|
+-----------------------------
|
|
|
+
|
|
|
+Before powering up your ESP-WROVER-KIT, please make sure that the board is in good condition with no obvious signs of damage.
|
|
|
+
|
|
|
+
|
|
|
+Initial Setup
|
|
|
+^^^^^^^^^^^^^
|
|
|
+
|
|
|
+Please set only the following jumpers shown in the pictures below:
|
|
|
+
|
|
|
+- Select USB as the power source using the jumper block JP7.
|
|
|
+
|
|
|
+- Enable UART communication using the jumper block JP2.
|
|
|
+
|
|
|
+======================== ==========================
|
|
|
+Power up from USB port Enable UART communication
|
|
|
+======================== ==========================
|
|
|
+|jp7-usb_5v| |jp2-tx-rx|
|
|
|
+======================== ==========================
|
|
|
+
|
|
|
+Do not install any other jumpers.
|
|
|
+
|
|
|
+Turn the **Power Switch** to ON, the **5V Power On LED** should light up.
|
|
|
+
|
|
|
+Now to Development
|
|
|
+^^^^^^^^^^^^^^^^^^
|
|
|
+
|
|
|
+Please proceed to :doc:`index`, where Section :ref:`get-started-step-by-step` will quickly help you set up the development environment and then flash an example project onto your board.
|
|
|
+
|
|
|
+
|
|
|
+Related Documents
|
|
|
+-----------------
|
|
|
+
|
|
|
+* `ESP-WROVER-KIT V4.1 schematic`_ (PDF)
|
|
|
+* `ESP32 Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf>`_ (PDF)
|
|
|
+* `ESP32-WROVER-B Datasheet <https://espressif.com/sites/default/files/documentation/esp32-wrover-b_datasheet_en.pdf>`_ (PDF)
|
|
|
+* :doc:`../api-guides/jtag-debugging/index`
|
|
|
+* :doc:`../hw-reference/index`
|
|
|
+
|
|
|
+.. |jp7-ext_5v| image:: ../../_static/esp-wrover-kit-v4.1-jp7-ext_5v.jpg
|
|
|
+.. |jp7-usb_5v| image:: ../../_static/esp-wrover-kit-v4.1-jp7-usb_5v.jpg
|
|
|
+.. |jp2-jtag| image:: ../../_static/esp-wrover-kit-v4.1-jp2-jtag.jpg
|
|
|
+.. |jp2-tx-rx| image:: ../../_static/esp-wrover-kit-v4.1-jp2-tx-rx.jpg
|
|
|
+.. |jp14| image:: ../../_static/esp-wrover-kit-v4.1-jp14.jpg
|
|
|
+
|
|
|
+.. _ESP-WROVER-KIT V4.1 schematic: https://dl.espressif.com/dl/schematics/ESP-WROVER-KIT_V4_1.pdf
|
|
|
+
|
|
|
+.. toctree::
|
|
|
+ :hidden:
|
|
|
+
|
|
|
+ get-started-wrover-kit-v3.rst
|
|
|
+ get-started-wrover-kit-v2.rst
|
Kirill Chalov
