wdt: Fix timeout and RTC_SLOW_CLK

RTC_SLOW_CLK
ESP32:    150kHz
ESP32-S2:  90kHz
ESP32-S3: 150kHz
ESP32-C3: 150kHz

components/bt/controller/esp32c3/Kconfig.in

@@ -331,10 +331,10 @@ menu "MODEM SLEEP Options"
                 modem sleep to be used with both DFS and light sleep.
 
         config BT_CTRL_LPCLK_SEL_RTC_SLOW
-            bool "Internal 90kHz RC oscillator"
+            bool "Internal 150kHz RC oscillator"
             depends on ESP32C3_RTC_CLK_SRC_INT_RC
             help
-                Internal 90kHz RC oscillator.
+                Internal 150kHz RC oscillator.
 
 
     endchoice

components/bt/controller/esp32c3/bt.c

@@ -1045,7 +1045,7 @@ esp_err_t esp_bt_controller_init(esp_bt_controller_config_t *cfg)
         if (rtc_clk_slow_freq_get() == RTC_SLOW_FREQ_RTC) {
             s_lp_cntl.lpclk_sel = BTDM_LPCLK_SEL_RTC_SLOW; // set default value
         } else {
-            ESP_LOGW(BTDM_LOG_TAG, "Internal 90kHz RC oscillator not detected, fall back to main XTAL as Bluetooth sleep clock\n"
+            ESP_LOGW(BTDM_LOG_TAG, "Internal 150kHz RC oscillator not detected, fall back to main XTAL as Bluetooth sleep clock\n"
                  "light sleep mode will not be able to apply when bluetooth is enabled");
             s_lp_cntl.lpclk_sel = BTDM_LPCLK_SEL_XTAL; // set default value
         }

components/bt/include/esp32c3/include/esp_bt.h

@@ -73,7 +73,7 @@ typedef enum {
     ESP_BT_SLEEP_CLOCK_NONE            = 0,   /*!< Sleep clock not configured */
     ESP_BT_SLEEP_CLOCK_MAIN_XTAL       = 1,   /*!< SoC main crystal */
     ESP_BT_SLEEP_CLOCK_EXT_32K_XTAL    = 2,   /*!< External 32.768kHz crystal */
-    ESP_BT_SLEEP_CLOCK_RTC_SLOW        = 3,   /*!< Internal 90kHz RC oscillator */
+    ESP_BT_SLEEP_CLOCK_RTC_SLOW        = 3,   /*!< Internal 150kHz RC oscillator */
     ESP_BT_SLEEP_CLOCK_FPGA_32K        = 4,   /*!< Hardwired 32KHz clock temporarily used for FPGA */
 } esp_bt_sleep_clock_t;
 

components/esp32c3/Kconfig

@@ -162,7 +162,7 @@ menu "ESP32C3-Specific"
             Choose which clock is used as RTC clock source.
 
         config ESP32C3_RTC_CLK_SRC_INT_RC
-            bool "Internal 90kHz RC oscillator"
+            bool "Internal 150kHz RC oscillator"
         config ESP32C3_RTC_CLK_SRC_EXT_CRYS
             bool "External 32kHz crystal"
             select ESP_SYSTEM_RTC_EXT_XTAL
@@ -188,7 +188,7 @@ menu "ESP32C3-Specific"
             When this option is set to 0, clock calibration will not be performed at
             startup, and approximate clock frequencies will be assumed:
 
-            - 90000 Hz if internal RC oscillator is used as clock source. For this use value 1024.
+            - 150000 Hz if internal RC oscillator is used as clock source. For this use value 1024.
             - 32768 Hz if the 32k crystal oscillator is used. For this use value 3000 or more.
               In case more value will help improve the definition of the launch of the crystal.
               If the crystal could not start, it will be switched to internal RC.

components/esp32s3/Kconfig

@@ -448,7 +448,7 @@ menu "ESP32S3-Specific"
             Choose which clock is used as RTC clock source.
 
         config ESP32S3_RTC_CLK_SRC_INT_RC
-            bool "Internal 90kHz RC oscillator"
+            bool "Internal 150kHz RC oscillator"
         config ESP32S3_RTC_CLK_SRC_EXT_CRYS
             bool "External 32kHz crystal"
             select ESP_SYSTEM_RTC_EXT_XTAL
@@ -474,7 +474,7 @@ menu "ESP32S3-Specific"
             When this option is set to 0, clock calibration will not be performed at
             startup, and approximate clock frequencies will be assumed:
 
-            - 90000 Hz if internal RC oscillator is used as clock source. For this use value 1024.
+            - 150000 Hz if internal RC oscillator is used as clock source. For this use value 1024.
             - 32768 Hz if the 32k crystal oscillator is used. For this use value 3000 or more.
               In case more value will help improve the definition of the launch of the crystal.
               If the crystal could not start, it will be switched to internal RC.

components/esp_hw_support/port/esp32c3/rtc_clk.c

@@ -180,7 +180,7 @@ rtc_slow_freq_t rtc_clk_slow_freq_get(void)
 uint32_t rtc_clk_slow_freq_get_hz(void)
 {
     switch (rtc_clk_slow_freq_get()) {
-    case RTC_SLOW_FREQ_RTC: return RTC_SLOW_CLK_FREQ_90K;
+    case RTC_SLOW_FREQ_RTC: return RTC_SLOW_CLK_FREQ_150K;
     case RTC_SLOW_FREQ_32K_XTAL: return RTC_SLOW_CLK_FREQ_32K;
     case RTC_SLOW_FREQ_8MD256: return RTC_SLOW_CLK_FREQ_8MD256;
     }

components/esp_hw_support/port/esp32c3/rtc_clk_init.c

@@ -36,10 +36,10 @@ void rtc_clk_init(rtc_clk_config_t cfg)
 {
     rtc_cpu_freq_config_t old_config, new_config;
 
-    /* Set tuning parameters for 8M and 90k clocks.
+    /* Set tuning parameters for 8M and 150k clocks.
      * Note: this doesn't attempt to set the clocks to precise frequencies.
      * Instead, we calibrate these clocks against XTAL frequency later, when necessary.
-     * - SCK_DCAP value controls tuning of 90k clock.
+     * - SCK_DCAP value controls tuning of 150k clock.
      *   The higher the value of DCAP is, the lower is the frequency.
      * - CK8M_DFREQ value controls tuning of 8M clock.
      *   CLK_8M_DFREQ constant gives the best temperature characteristics.
@@ -47,7 +47,7 @@ void rtc_clk_init(rtc_clk_config_t cfg)
     REG_SET_FIELD(RTC_CNTL_REG, RTC_CNTL_SCK_DCAP, cfg.slow_clk_dcap);
     REG_SET_FIELD(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_CK8M_DFREQ, cfg.clk_8m_dfreq);
 
-    /* Configure 90k clock division */
+    /* Configure 150k clock division */
     rtc_clk_divider_set(cfg.clk_rtc_clk_div);
 
     /* Configure 8M clock division */

components/esp_hw_support/port/esp32c3/rtc_time.c

@@ -40,7 +40,7 @@
 uint32_t rtc_clk_cal_internal(rtc_cal_sel_t cal_clk, uint32_t slowclk_cycles)
 {
     /* On ESP32C3, choosing RTC_CAL_RTC_MUX results in calibration of
-     * the 90k RTC clock regardless of the currenlty selected SLOW_CLK.
+     * the 150k RTC clock regardless of the currenlty selected SLOW_CLK.
      * On the ESP32, it used the currently selected SLOW_CLK.
      * The following code emulates ESP32 behavior:
      */
@@ -52,7 +52,7 @@ uint32_t rtc_clk_cal_internal(rtc_cal_sel_t cal_clk, uint32_t slowclk_cycles)
             cal_clk = RTC_CAL_8MD256;
         }
     }
-    /* Enable requested clock (90k clock is always on) */
+    /* Enable requested clock (150k clock is always on) */
     int dig_32k_xtal_state = REG_GET_FIELD(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_DIG_XTAL32K_EN);
     if (cal_clk == RTC_CAL_32K_XTAL && !dig_32k_xtal_state) {
         REG_SET_FIELD(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_DIG_XTAL32K_EN, 1);
@@ -84,8 +84,8 @@ uint32_t rtc_clk_cal_internal(rtc_cal_sel_t cal_clk, uint32_t slowclk_cycles)
         REG_SET_FIELD(TIMG_RTCCALICFG2_REG(0), TIMG_RTC_CALI_TIMEOUT_THRES, RTC_SLOW_CLK_8MD256_CAL_TIMEOUT_THRES(slowclk_cycles));
         expected_freq = RTC_SLOW_CLK_FREQ_8MD256;
     } else {
-        REG_SET_FIELD(TIMG_RTCCALICFG2_REG(0), TIMG_RTC_CALI_TIMEOUT_THRES, RTC_SLOW_CLK_90K_CAL_TIMEOUT_THRES(slowclk_cycles));
-        expected_freq = RTC_SLOW_CLK_FREQ_90K;
+        REG_SET_FIELD(TIMG_RTCCALICFG2_REG(0), TIMG_RTC_CALI_TIMEOUT_THRES, RTC_SLOW_CLK_150K_CAL_TIMEOUT_THRES(slowclk_cycles));
+        expected_freq = RTC_SLOW_CLK_FREQ_150K;
     }
     uint32_t us_time_estimate = (uint32_t) (((uint64_t) slowclk_cycles) * MHZ / expected_freq);
     /* Start calibration */

components/esp_hw_support/port/esp32s3/rtc_clk.c

@@ -187,7 +187,7 @@ rtc_slow_freq_t rtc_clk_slow_freq_get(void)
 uint32_t rtc_clk_slow_freq_get_hz(void)
 {
     switch (rtc_clk_slow_freq_get()) {
-    case RTC_SLOW_FREQ_RTC: return RTC_SLOW_CLK_FREQ_90K;
+    case RTC_SLOW_FREQ_RTC: return RTC_SLOW_CLK_FREQ_150K;
     case RTC_SLOW_FREQ_32K_XTAL: return RTC_SLOW_CLK_FREQ_32K;
     case RTC_SLOW_FREQ_8MD256: return RTC_SLOW_CLK_FREQ_8MD256;
     }

components/esp_hw_support/port/esp32s3/rtc_clk_init.c

@@ -32,10 +32,10 @@ void rtc_clk_init(rtc_clk_config_t cfg)
 {
     rtc_cpu_freq_config_t old_config, new_config;
 
-    /* Set tuning parameters for 8M and 90k clocks.
+    /* Set tuning parameters for 8M and 150k clocks.
      * Note: this doesn't attempt to set the clocks to precise frequencies.
      * Instead, we calibrate these clocks against XTAL frequency later, when necessary.
-     * - SCK_DCAP value controls tuning of 90k clock.
+     * - SCK_DCAP value controls tuning of 150k clock.
      *   The higher the value of DCAP is, the lower is the frequency.
      * - CK8M_DFREQ value controls tuning of 8M clock.
      *   CLK_8M_DFREQ constant gives the best temperature characteristics.
@@ -43,7 +43,7 @@ void rtc_clk_init(rtc_clk_config_t cfg)
     REG_SET_FIELD(RTC_CNTL_REG, RTC_CNTL_SCK_DCAP, cfg.slow_clk_dcap);
     REG_SET_FIELD(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_CK8M_DFREQ, cfg.clk_8m_dfreq);
 
-    /* Configure 90k clock division */
+    /* Configure 150k clock division */
     rtc_clk_divider_set(cfg.clk_rtc_clk_div);
 
     /* Configure 8M clock division */

components/esp_hw_support/port/esp32s3/rtc_time.c

@@ -39,7 +39,7 @@
 uint32_t rtc_clk_cal_internal(rtc_cal_sel_t cal_clk, uint32_t slowclk_cycles)
 {
     /* On ESP32S3, choosing RTC_CAL_RTC_MUX results in calibration of
-     * the 90k RTC clock regardless of the currenlty selected SLOW_CLK.
+     * the 150k RTC clock regardless of the currenlty selected SLOW_CLK.
      * On the ESP32, it used the currently selected SLOW_CLK.
      * The following code emulates ESP32 behavior:
      */
@@ -51,7 +51,7 @@ uint32_t rtc_clk_cal_internal(rtc_cal_sel_t cal_clk, uint32_t slowclk_cycles)
             cal_clk = RTC_CAL_8MD256;
         }
     }
-    /* Enable requested clock (90k clock is always on) */
+    /* Enable requested clock (150k clock is always on) */
     int dig_32k_xtal_state = REG_GET_FIELD(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_DIG_XTAL32K_EN);
     if (cal_clk == RTC_CAL_32K_XTAL && !dig_32k_xtal_state) {
         REG_SET_FIELD(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_DIG_XTAL32K_EN, 1);
@@ -83,8 +83,8 @@ uint32_t rtc_clk_cal_internal(rtc_cal_sel_t cal_clk, uint32_t slowclk_cycles)
         REG_SET_FIELD(TIMG_RTCCALICFG2_REG(0), TIMG_RTC_CALI_TIMEOUT_THRES, RTC_SLOW_CLK_8MD256_CAL_TIMEOUT_THRES(slowclk_cycles));
         expected_freq = RTC_SLOW_CLK_FREQ_8MD256;
     } else {
-        REG_SET_FIELD(TIMG_RTCCALICFG2_REG(0), TIMG_RTC_CALI_TIMEOUT_THRES, RTC_SLOW_CLK_90K_CAL_TIMEOUT_THRES(slowclk_cycles));
-        expected_freq = RTC_SLOW_CLK_FREQ_90K;
+        REG_SET_FIELD(TIMG_RTCCALICFG2_REG(0), TIMG_RTC_CALI_TIMEOUT_THRES, RTC_SLOW_CLK_150K_CAL_TIMEOUT_THRES(slowclk_cycles));
+        expected_freq = RTC_SLOW_CLK_FREQ_150K;
     }
     uint32_t us_time_estimate = (uint32_t) (((uint64_t) slowclk_cycles) * MHZ / expected_freq);
     /* Start calibration */

components/esp_system/port/soc/esp32c3/clk.c

@@ -60,7 +60,7 @@
  * For convenience, lower 2 bits should correspond to rtc_slow_freq_t values.
  */
 typedef enum {
-    SLOW_CLK_RTC = RTC_SLOW_FREQ_RTC,           //!< Internal 90 kHz RC oscillator
+    SLOW_CLK_RTC = RTC_SLOW_FREQ_RTC,           //!< Internal 150 kHz RC oscillator
     SLOW_CLK_32K_XTAL = RTC_SLOW_FREQ_32K_XTAL, //!< External 32 kHz XTAL
     SLOW_CLK_8MD256 = RTC_SLOW_FREQ_8MD256,     //!< Internal 8 MHz RC oscillator, divided by 256
     SLOW_CLK_32K_EXT_OSC = RTC_SLOW_FREQ_32K_XTAL | EXT_OSC_FLAG //!< External 32k oscillator connected to 32K_XP pin
@@ -89,10 +89,10 @@ static const char *TAG = "clk";
 
 #ifdef CONFIG_BOOTLOADER_WDT_ENABLE
     // WDT uses a SLOW_CLK clock source. After a function select_rtc_slow_clk a frequency of this source can changed.
-    // If the frequency changes from 90kHz to 32kHz, then the timeout set for the WDT will increase 2.8 times.
+    // If the frequency changes from 150kHz to 32kHz, then the timeout set for the WDT will increase 4.6 times.
     // Therefore, for the time of frequency change, set a new lower timeout value (1.6 sec).
     // This prevents excessive delay before resetting in case the supply voltage is drawdown.
-    // (If frequency is changed from 90kHz to 32kHz then WDT timeout will increased to 1.6sec * 90/32 = 4.5 sec).
+    // (If frequency is changed from 150kHz to 32kHz then WDT timeout will increased to 1.6sec * 150/32 = 7.5 sec).
     wdt_hal_context_t rtc_wdt_ctx = {.inst = WDT_RWDT, .rwdt_dev = &RTCCNTL};
     uint32_t stage_timeout_ticks = (uint32_t)(1600ULL * rtc_clk_slow_freq_get_hz() / 1000ULL);
     wdt_hal_write_protect_disable(&rtc_wdt_ctx);
@@ -172,7 +172,7 @@ static void select_rtc_slow_clk(slow_clk_sel_t slow_clk)
                     if (retry_32k_xtal-- > 0) {
                         continue;
                     }
-                    ESP_EARLY_LOGW(TAG, "32 kHz XTAL not found, switching to internal 90 kHz oscillator");
+                    ESP_EARLY_LOGW(TAG, "32 kHz XTAL not found, switching to internal 150 kHz oscillator");
                     rtc_slow_freq = RTC_SLOW_FREQ_RTC;
                 }
             }

components/esp_system/port/soc/esp32s3/clk.c

@@ -66,7 +66,7 @@ static const char *TAG = "clk";
  * For convenience, lower 2 bits should correspond to rtc_slow_freq_t values.
  */
 typedef enum {
-    SLOW_CLK_RTC = RTC_SLOW_FREQ_RTC,           //!< Internal 90 kHz RC oscillator
+    SLOW_CLK_RTC = RTC_SLOW_FREQ_RTC,           //!< Internal 150 kHz RC oscillator
     SLOW_CLK_32K_XTAL = RTC_SLOW_FREQ_32K_XTAL, //!< External 32 kHz XTAL
     SLOW_CLK_8MD256 = RTC_SLOW_FREQ_8MD256,     //!< Internal 8 MHz RC oscillator, divided by 256
     SLOW_CLK_32K_EXT_OSC = RTC_SLOW_FREQ_32K_XTAL | EXT_OSC_FLAG //!< External 32k oscillator connected to 32K_XP pin
@@ -85,10 +85,10 @@ static void select_rtc_slow_clk(slow_clk_sel_t slow_clk);
 
 #ifdef CONFIG_BOOTLOADER_WDT_ENABLE
     // WDT uses a SLOW_CLK clock source. After a function select_rtc_slow_clk a frequency of this source can changed.
-    // If the frequency changes from 90kHz to 32kHz, then the timeout set for the WDT will increase 2.8 times.
+    // If the frequency changes from 150kHz to 32kHz, then the timeout set for the WDT will increase 4.6 times.
     // Therefore, for the time of frequency change, set a new lower timeout value (1.6 sec).
     // This prevents excessive delay before resetting in case the supply voltage is drawdown.
-    // (If frequency is changed from 90kHz to 32kHz then WDT timeout will increased to 1.6sec * 90/32 = 4.5 sec).
+    // (If frequency is changed from 150kHz to 32kHz then WDT timeout will increased to 1.6sec * 150/32 = 7.5 sec).
     wdt_hal_context_t rtc_wdt_ctx = {.inst = WDT_RWDT, .rwdt_dev = &RTCCNTL};
     uint32_t stage_timeout_ticks = (uint32_t)(1600ULL * rtc_clk_slow_freq_get_hz() / 1000ULL);
     wdt_hal_write_protect_disable(&rtc_wdt_ctx);
@@ -170,7 +170,7 @@ static void select_rtc_slow_clk(slow_clk_sel_t slow_clk)
                     if (retry_32k_xtal-- > 0) {
                         continue;
                     }
-                    ESP_EARLY_LOGW(TAG, "32 kHz XTAL not found, switching to internal 90 kHz oscillator");
+                    ESP_EARLY_LOGW(TAG, "32 kHz XTAL not found, switching to internal 150 kHz oscillator");
                     rtc_slow_freq = RTC_SLOW_FREQ_RTC;
                 }
             }

components/hal/esp32s3/include/hal/touch_sensor_ll.h

@@ -72,7 +72,7 @@ static inline void touch_ll_get_measure_times(uint16_t *meas_time)
  */
 static inline void touch_ll_set_sleep_time(uint16_t sleep_time)
 {
-    // touch sensor sleep cycle Time = sleep_cycle / RTC_SLOW_CLK(90k)
+    // touch sensor sleep cycle Time = sleep_cycle / RTC_SLOW_CLK(150k)
     RTCCNTL.touch_ctrl1.touch_sleep_cycles = sleep_time;
 }
 

components/soc/esp32c3/include/soc/rtc.h

@@ -55,9 +55,9 @@ extern "C" {
 
 #define RTC_SLOW_CLK_X32K_CAL_TIMEOUT_THRES(cycles)  (cycles << 12)
 #define RTC_SLOW_CLK_8MD256_CAL_TIMEOUT_THRES(cycles)  (cycles << 12)
-#define RTC_SLOW_CLK_90K_CAL_TIMEOUT_THRES(cycles)  (cycles << 10)
+#define RTC_SLOW_CLK_150K_CAL_TIMEOUT_THRES(cycles)  (cycles << 10)
 
-#define RTC_SLOW_CLK_FREQ_90K      90000
+#define RTC_SLOW_CLK_FREQ_150K      150000
 #define RTC_SLOW_CLK_FREQ_8MD256    (RTC_FAST_CLK_FREQ_APPROX / 256)
 #define RTC_SLOW_CLK_FREQ_32K       32768
 
@@ -210,7 +210,7 @@ typedef struct {
     rtc_slow_freq_t slow_freq : 2;  //!< RTC_SLOW_CLK frequency to set
     uint32_t clk_rtc_clk_div : 8;
     uint32_t clk_8m_clk_div : 3;        //!< RTC 8M clock divider (division is by clk_8m_div+1, i.e. 0 means 8MHz frequency)
-    uint32_t slow_clk_dcap : 8;     //!< RTC 90k clock adjustment parameter (higher value leads to lower frequency)
+    uint32_t slow_clk_dcap : 8;     //!< RTC 150k clock adjustment parameter (higher value leads to lower frequency)
     uint32_t clk_8m_dfreq : 8;      //!< RTC 8m clock adjustment parameter (higher value leads to higher frequency)
 } rtc_clk_config_t;
 

components/soc/esp32s2/include/soc/rtc.h

@@ -178,7 +178,7 @@ typedef struct rtc_cpu_freq_config_s {
  * @brief RTC SLOW_CLK frequency values
  */
 typedef enum {
-    RTC_SLOW_FREQ_RTC = 0,      //!< Internal 150 kHz RC oscillator
+    RTC_SLOW_FREQ_RTC = 0,      //!< Internal 90 kHz RC oscillator
     RTC_SLOW_FREQ_32K_XTAL = 1, //!< External 32 kHz XTAL
     RTC_SLOW_FREQ_8MD256 = 2,   //!< Internal 8 MHz RC oscillator, divided by 256
 } rtc_slow_freq_t;
@@ -426,7 +426,7 @@ rtc_slow_freq_t rtc_clk_slow_freq_get(void);
 /**
  * @brief Get the approximate frequency of RTC_SLOW_CLK, in Hz
  *
- * - if RTC_SLOW_FREQ_RTC is selected, returns ~150000
+ * - if RTC_SLOW_FREQ_RTC is selected, returns ~90000
  * - if RTC_SLOW_FREQ_32K_XTAL is selected, returns 32768
  * - if RTC_SLOW_FREQ_8MD256 is selected, returns ~33000
  *

components/soc/esp32s3/include/soc/rtc.h

@@ -55,9 +55,9 @@ extern "C" {
 
 #define RTC_SLOW_CLK_X32K_CAL_TIMEOUT_THRES(cycles)  (cycles << 12)
 #define RTC_SLOW_CLK_8MD256_CAL_TIMEOUT_THRES(cycles)  (cycles << 12)
-#define RTC_SLOW_CLK_90K_CAL_TIMEOUT_THRES(cycles)  (cycles << 10)
+#define RTC_SLOW_CLK_150K_CAL_TIMEOUT_THRES(cycles)  (cycles << 10)
 
-#define RTC_SLOW_CLK_FREQ_90K      90000
+#define RTC_SLOW_CLK_FREQ_150K      150000
 #define RTC_SLOW_CLK_FREQ_8MD256    (RTC_FAST_CLK_FREQ_APPROX / 256)
 #define RTC_SLOW_CLK_FREQ_32K       32768
 
@@ -214,7 +214,7 @@ typedef struct {
     rtc_slow_freq_t slow_freq : 2;  //!< RTC_SLOW_CLK frequency to set
     uint32_t clk_rtc_clk_div : 8;
     uint32_t clk_8m_clk_div : 3;        //!< RTC 8M clock divider (division is by clk_8m_div+1, i.e. 0 means 8MHz frequency)
-    uint32_t slow_clk_dcap : 8;     //!< RTC 90k clock adjustment parameter (higher value leads to lower frequency)
+    uint32_t slow_clk_dcap : 8;     //!< RTC 150k clock adjustment parameter (higher value leads to lower frequency)
     uint32_t clk_8m_dfreq : 8;      //!< RTC 8m clock adjustment parameter (higher value leads to higher frequency)
 } rtc_clk_config_t;
 

docs/en/api-guides/ulp-risc-v.rst

@@ -136,7 +136,9 @@ Once the program is loaded into RTC memory, the application can start it, callin
 ULP-RISC-V Program Flow
 -----------------------
 
-The ULP-RISC-V coprocessor is started by a timer. The timer is started once :cpp:func:`ulp_riscv_run` is called. The timer counts the number of RTC_SLOW_CLK ticks (by default, produced by an internal 90 kHz RC oscillator). The number of ticks is set using ``RTC_CNTL_ULP_CP_TIMER_1_REG`` register. When starting the ULP, ``RTC_CNTL_ULP_CP_TIMER_1_REG`` will be used to set the number of timer ticks.
+{IDF_TARGET_RTC_CLK_FRE:default="150kHz", esp32s2="90kHz"}
+
+The ULP-RISC-V coprocessor is started by a timer. The timer is started once :cpp:func:`ulp_riscv_run` is called. The timer counts the number of RTC_SLOW_CLK ticks (by default, produced by an internal {IDF_TARGET_RTC_CLK_FRE} RC oscillator). The number of ticks is set using ``RTC_CNTL_ULP_CP_TIMER_1_REG`` register. When starting the ULP, ``RTC_CNTL_ULP_CP_TIMER_1_REG`` will be used to set the number of timer ticks.
 
 The application can set ULP timer period values (RTC_CNTL_ULP_CP_TIMER_1_REG) using the :cpp:func:`ulp_set_wakeup_period` function.
 

docs/en/api-reference/system/system_time.rst

@@ -1,7 +1,7 @@
 System Time
 ===========
 
-{IDF_TARGET_RTC_CLK_FRE:default="90kHz", esp32="150kHz"}
+{IDF_TARGET_RTC_CLK_FRE:default="150kHz", esp32s2="90kHz"}
 {IDF_TARGET_HARDWARE_DESIGN_URL:default="`ESP32 Hardware Design Guidelines <https://www.espressif.com/sites/default/files/documentation/esp32_hardware_design_guidelines_en.pdf#page=10>`_", esp32="`ESP32 Hardware Design Guidelines <https://www.espressif.com/sites/default/files/documentation/esp32_hardware_design_guidelines_en.pdf#page=10>`_", esp32s2="`ESP32-S2 Hardware Design Guidelines <https://www.espressif.com/sites/default/files/documentation/esp32-s2_hardware_design_guidelines_en.pdf#page=10>`_"}
 
 Overview