|
|
@@ -15,7 +15,7 @@ What You Need
|
|
|
The Board
|
|
|
---------
|
|
|
|
|
|
-This section describes functionality of ESP-WROVER-KIT board and configuration options. If you like to start using it now, go directly to section :ref:`esp-wrover-start-developement`
|
|
|
+This section describes functionality of ESP-WROVER-KIT board and configuration options. If you like to start using it now, go directly to section :ref:`esp-wrover-start-development`
|
|
|
|
|
|
|
|
|
Overview
|
|
|
@@ -25,7 +25,7 @@ The ESP-WROVER-KIT is a development board produced by `Espressif <http://espress
|
|
|
|
|
|
.. note::
|
|
|
|
|
|
- ESP-WROVER-KIT integrates the ESP-WROOM-32 module by default.
|
|
|
+ ESP-WROVER-KIT integrates the ESP-WROOM-32 module, while ESP-WROVER-KIT-RVB integrates the ESP32-WROVER. Both ESP-WROVER-KIT and ESP-WROVER-KIT-RVB have the same baseboard. The only difference is the module.
|
|
|
|
|
|
|
|
|
Functionality Overview
|
|
|
@@ -117,31 +117,33 @@ Setup Options
|
|
|
|
|
|
There are five jumper headers available to set up the board functionality. Typical options to select from are listed in table below.
|
|
|
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| Header | Jumper Setting | Description of Functionality |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| JP1 | |jp1-both| | Assert GPIO2 low during each download |
|
|
|
-| | | (by jumping it to GPIO0) |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| JP1 | |jp1-sd_io2| | Enable pull up for the Micro SD Card |
|
|
|
-| | | |
|
|
|
-| | | **Note:** applies to ESP-WROVER-KIT V2 only |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| JP7 | |jp7-ext_5v| | Power ESP-WROVER-KIT board from an external |
|
|
|
-| | | power supply |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| JP7 | |jp7-usb_5v| | Power ESP-WROVER-KIT board from an USB port |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| JP8 | |jp8| | Enable JTAG functionality |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| JP11 | |jp11-rx-tx| | Enable UART communication |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-| JP14 | |jp14| | Enable RTS/CTS flow control for serial |
|
|
|
-| | | communication |
|
|
|
-+--------+----------------------+-------------------------------------------------+
|
|
|
-
|
|
|
-
|
|
|
-.. _esp-wrover-start-developement:
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| Header | Jumper Setting | Description of Functionality |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| JP1 | |jp1-both| | Assert GPIO2 low during each download |
|
|
|
+| | | (by jumping it to GPIO0) |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| JP1 | |jp1-sd_io2| | Enable pull up for the Micro SD Card, |
|
|
|
+| | | ESP-WROVER-KIT V2 only |
|
|
|
+| | | |
|
|
|
+| | | **Note:** |
|
|
|
+| | | No jumpers are needed for SD card function on the V3 |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| JP7 | |jp7-ext_5v| | Power ESP-WROVER-KIT board from an external |
|
|
|
+| | | power supply |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| JP7 | |jp7-usb_5v| | Power ESP-WROVER-KIT board from an USB port |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| JP8 | |jp8| | Enable JTAG functionality |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| JP11 | |jp11-rx-tx| | Enable UART communication |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+| JP14 | |jp14| | Enable RTS/CTS flow control for serial |
|
|
|
+| | | communication |
|
|
|
++--------+----------------------+-----------------------------------------------------------+
|
|
|
+
|
|
|
+
|
|
|
+.. _esp-wrover-start-development:
|
|
|
|
|
|
Start Application Development
|
|
|
-----------------------------
|
krzychb