esp-idf/components/soc/esp32c6/include/soc/i2c_reg.h

/**
 * SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD
 *
 *  SPDX-License-Identifier: Apache-2.0
 */
#pragma once

#include <stdint.h>
#include "soc/soc.h"
#ifdef __cplusplus
extern "C" {
#endif

/** I2C_SCL_LOW_PERIOD_REG register
 *  Configures the low level width of the SCL
 *  Clock
 */
#define I2C_SCL_LOW_PERIOD_REG(i) (REG_I2C_BASE(i) + 0x0)
/** I2C_SCL_LOW_PERIOD : R/W; bitpos: [8:0]; default: 0;
 *  This register is used to configure for how long SCL remains low in master mode, in
 *  I2C module clock cycles.
 */
#define I2C_SCL_LOW_PERIOD    0x000001FFU
#define I2C_SCL_LOW_PERIOD_M  (I2C_SCL_LOW_PERIOD_V << I2C_SCL_LOW_PERIOD_S)
#define I2C_SCL_LOW_PERIOD_V  0x000001FFU
#define I2C_SCL_LOW_PERIOD_S  0

/** I2C_CTR_REG register
 *  Transmission setting
 */
#define I2C_CTR_REG(i) (REG_I2C_BASE(i) + 0x4)
/** I2C_SDA_FORCE_OUT : R/W; bitpos: [0]; default: 0;
 *  1: direct output, 0: open drain output.
 */
#define I2C_SDA_FORCE_OUT    (BIT(0))
#define I2C_SDA_FORCE_OUT_M  (I2C_SDA_FORCE_OUT_V << I2C_SDA_FORCE_OUT_S)
#define I2C_SDA_FORCE_OUT_V  0x00000001U
#define I2C_SDA_FORCE_OUT_S  0
/** I2C_SCL_FORCE_OUT : R/W; bitpos: [1]; default: 0;
 *  1: direct output, 0: open drain output.
 */
#define I2C_SCL_FORCE_OUT    (BIT(1))
#define I2C_SCL_FORCE_OUT_M  (I2C_SCL_FORCE_OUT_V << I2C_SCL_FORCE_OUT_S)
#define I2C_SCL_FORCE_OUT_V  0x00000001U
#define I2C_SCL_FORCE_OUT_S  1
/** I2C_SAMPLE_SCL_LEVEL : R/W; bitpos: [2]; default: 0;
 *  This register is used to select the sample mode.
 *  1: sample SDA data on the SCL low level.
 *  0: sample SDA data on the SCL high level.
 */
#define I2C_SAMPLE_SCL_LEVEL    (BIT(2))
#define I2C_SAMPLE_SCL_LEVEL_M  (I2C_SAMPLE_SCL_LEVEL_V << I2C_SAMPLE_SCL_LEVEL_S)
#define I2C_SAMPLE_SCL_LEVEL_V  0x00000001U
#define I2C_SAMPLE_SCL_LEVEL_S  2
/** I2C_RX_FULL_ACK_LEVEL : R/W; bitpos: [3]; default: 1;
 *  This register is used to configure the ACK value that need to sent by master when
 *  the rx_fifo_cnt has reached the threshold.
 */
#define I2C_RX_FULL_ACK_LEVEL    (BIT(3))
#define I2C_RX_FULL_ACK_LEVEL_M  (I2C_RX_FULL_ACK_LEVEL_V << I2C_RX_FULL_ACK_LEVEL_S)
#define I2C_RX_FULL_ACK_LEVEL_V  0x00000001U
#define I2C_RX_FULL_ACK_LEVEL_S  3
/** I2C_MS_MODE : R/W; bitpos: [4]; default: 0;
 *  Set this bit to configure the module as an I2C Master. Clear this bit to configure
 *  the
 *  module as an I2C Slave.
 */
#define I2C_MS_MODE    (BIT(4))
#define I2C_MS_MODE_M  (I2C_MS_MODE_V << I2C_MS_MODE_S)
#define I2C_MS_MODE_V  0x00000001U
#define I2C_MS_MODE_S  4
/** I2C_TRANS_START : WT; bitpos: [5]; default: 0;
 *  Set this bit to start sending the data in txfifo.
 */
#define I2C_TRANS_START    (BIT(5))
#define I2C_TRANS_START_M  (I2C_TRANS_START_V << I2C_TRANS_START_S)
#define I2C_TRANS_START_V  0x00000001U
#define I2C_TRANS_START_S  5
/** I2C_TX_LSB_FIRST : R/W; bitpos: [6]; default: 0;
 *  This bit is used to control the sending mode for data needing to be sent.
 *  1: send data from the least significant bit,
 *  0: send data from the most significant bit.
 */
#define I2C_TX_LSB_FIRST    (BIT(6))
#define I2C_TX_LSB_FIRST_M  (I2C_TX_LSB_FIRST_V << I2C_TX_LSB_FIRST_S)
#define I2C_TX_LSB_FIRST_V  0x00000001U
#define I2C_TX_LSB_FIRST_S  6
/** I2C_RX_LSB_FIRST : R/W; bitpos: [7]; default: 0;
 *  This bit is used to control the storage mode for received data.
 *  1: receive data from the least significant bit,
 *  0: receive data from the most significant bit.
 */
#define I2C_RX_LSB_FIRST    (BIT(7))
#define I2C_RX_LSB_FIRST_M  (I2C_RX_LSB_FIRST_V << I2C_RX_LSB_FIRST_S)
#define I2C_RX_LSB_FIRST_V  0x00000001U
#define I2C_RX_LSB_FIRST_S  7
/** I2C_CLK_EN : R/W; bitpos: [8]; default: 0;
 *  Reserved
 */
#define I2C_CLK_EN    (BIT(8))
#define I2C_CLK_EN_M  (I2C_CLK_EN_V << I2C_CLK_EN_S)
#define I2C_CLK_EN_V  0x00000001U
#define I2C_CLK_EN_S  8
/** I2C_ARBITRATION_EN : R/W; bitpos: [9]; default: 1;
 *  This is the enable bit for arbitration_lost.
 */
#define I2C_ARBITRATION_EN    (BIT(9))
#define I2C_ARBITRATION_EN_M  (I2C_ARBITRATION_EN_V << I2C_ARBITRATION_EN_S)
#define I2C_ARBITRATION_EN_V  0x00000001U
#define I2C_ARBITRATION_EN_S  9
/** I2C_FSM_RST : WT; bitpos: [10]; default: 0;
 *  This register is used to reset the scl FMS.
 */
#define I2C_FSM_RST    (BIT(10))
#define I2C_FSM_RST_M  (I2C_FSM_RST_V << I2C_FSM_RST_S)
#define I2C_FSM_RST_V  0x00000001U
#define I2C_FSM_RST_S  10
/** I2C_CONF_UPGATE : WT; bitpos: [11]; default: 0;
 *  synchronization bit
 */
#define I2C_CONF_UPGATE    (BIT(11))
#define I2C_CONF_UPGATE_M  (I2C_CONF_UPGATE_V << I2C_CONF_UPGATE_S)
#define I2C_CONF_UPGATE_V  0x00000001U
#define I2C_CONF_UPGATE_S  11
/** I2C_SLV_TX_AUTO_START_EN : R/W; bitpos: [12]; default: 0;
 *  This is the enable bit for slave to send data automatically
 */
#define I2C_SLV_TX_AUTO_START_EN    (BIT(12))
#define I2C_SLV_TX_AUTO_START_EN_M  (I2C_SLV_TX_AUTO_START_EN_V << I2C_SLV_TX_AUTO_START_EN_S)
#define I2C_SLV_TX_AUTO_START_EN_V  0x00000001U
#define I2C_SLV_TX_AUTO_START_EN_S  12
/** I2C_ADDR_10BIT_RW_CHECK_EN : R/W; bitpos: [13]; default: 0;
 *  This is the enable bit to check if the r/w bit of 10bit addressing consists with
 *  I2C protocol
 */
#define I2C_ADDR_10BIT_RW_CHECK_EN    (BIT(13))
#define I2C_ADDR_10BIT_RW_CHECK_EN_M  (I2C_ADDR_10BIT_RW_CHECK_EN_V << I2C_ADDR_10BIT_RW_CHECK_EN_S)
#define I2C_ADDR_10BIT_RW_CHECK_EN_V  0x00000001U
#define I2C_ADDR_10BIT_RW_CHECK_EN_S  13
/** I2C_ADDR_BROADCASTING_EN : R/W; bitpos: [14]; default: 0;
 *  This is the enable bit to support the 7bit general call function.
 */
#define I2C_ADDR_BROADCASTING_EN    (BIT(14))
#define I2C_ADDR_BROADCASTING_EN_M  (I2C_ADDR_BROADCASTING_EN_V << I2C_ADDR_BROADCASTING_EN_S)
#define I2C_ADDR_BROADCASTING_EN_V  0x00000001U
#define I2C_ADDR_BROADCASTING_EN_S  14

/** I2C_SR_REG register
 *  Describe I2C work status.
 */
#define I2C_SR_REG(i) (REG_I2C_BASE(i) + 0x8)
/** I2C_RESP_REC : RO; bitpos: [0]; default: 0;
 *  The received ACK value in master mode or slave mode. 0: ACK, 1: NACK.
 */
#define I2C_RESP_REC    (BIT(0))
#define I2C_RESP_REC_M  (I2C_RESP_REC_V << I2C_RESP_REC_S)
#define I2C_RESP_REC_V  0x00000001U
#define I2C_RESP_REC_S  0
/** I2C_SLAVE_RW : RO; bitpos: [1]; default: 0;
 *  When in slave mode, 1: master reads from slave, 0: master writes to slave.
 */
#define I2C_SLAVE_RW    (BIT(1))
#define I2C_SLAVE_RW_M  (I2C_SLAVE_RW_V << I2C_SLAVE_RW_S)
#define I2C_SLAVE_RW_V  0x00000001U
#define I2C_SLAVE_RW_S  1
/** I2C_ARB_LOST : RO; bitpos: [3]; default: 0;
 *  When the I2C controller loses control of SCL line, this register changes to 1.
 */
#define I2C_ARB_LOST    (BIT(3))
#define I2C_ARB_LOST_M  (I2C_ARB_LOST_V << I2C_ARB_LOST_S)
#define I2C_ARB_LOST_V  0x00000001U
#define I2C_ARB_LOST_S  3
/** I2C_BUS_BUSY : RO; bitpos: [4]; default: 0;
 *  1: the I2C bus is busy transferring data, 0: the I2C bus is in idle state.
 */
#define I2C_BUS_BUSY    (BIT(4))
#define I2C_BUS_BUSY_M  (I2C_BUS_BUSY_V << I2C_BUS_BUSY_S)
#define I2C_BUS_BUSY_V  0x00000001U
#define I2C_BUS_BUSY_S  4
/** I2C_SLAVE_ADDRESSED : RO; bitpos: [5]; default: 0;
 *  When configured as an I2C Slave, and the address sent by the master is
 *  equal to the address of the slave, then this bit will be of high level.
 */
#define I2C_SLAVE_ADDRESSED    (BIT(5))
#define I2C_SLAVE_ADDRESSED_M  (I2C_SLAVE_ADDRESSED_V << I2C_SLAVE_ADDRESSED_S)
#define I2C_SLAVE_ADDRESSED_V  0x00000001U
#define I2C_SLAVE_ADDRESSED_S  5
/** I2C_RXFIFO_CNT : RO; bitpos: [13:8]; default: 0;
 *  This field represents the amount of data needed to be sent.
 */
#define I2C_RXFIFO_CNT    0x0000003FU
#define I2C_RXFIFO_CNT_M  (I2C_RXFIFO_CNT_V << I2C_RXFIFO_CNT_S)
#define I2C_RXFIFO_CNT_V  0x0000003FU
#define I2C_RXFIFO_CNT_S  8
/** I2C_STRETCH_CAUSE : RO; bitpos: [15:14]; default: 3;
 *  The cause of stretching SCL low in slave mode. 0:  stretching SCL low at the
 *  beginning of I2C read data state. 1: stretching SCL low when I2C Tx FIFO is empty
 *  in slave mode. 2: stretching SCL low when I2C Rx FIFO is full in slave mode.
 */
#define I2C_STRETCH_CAUSE    0x00000003U
#define I2C_STRETCH_CAUSE_M  (I2C_STRETCH_CAUSE_V << I2C_STRETCH_CAUSE_S)
#define I2C_STRETCH_CAUSE_V  0x00000003U
#define I2C_STRETCH_CAUSE_S  14
/** I2C_TXFIFO_CNT : RO; bitpos: [23:18]; default: 0;
 *  This field stores the amount of received data in RAM.
 */
#define I2C_TXFIFO_CNT    0x0000003FU
#define I2C_TXFIFO_CNT_M  (I2C_TXFIFO_CNT_V << I2C_TXFIFO_CNT_S)
#define I2C_TXFIFO_CNT_V  0x0000003FU
#define I2C_TXFIFO_CNT_S  18
/** I2C_SCL_MAIN_STATE_LAST : RO; bitpos: [26:24]; default: 0;
 *  This field indicates the states of the I2C module state machine.
 *  0: Idle, 1: Address shift, 2: ACK address, 3: Rx data, 4: Tx data, 5: Send ACK, 6:
 *  Wait ACK
 */
#define I2C_SCL_MAIN_STATE_LAST    0x00000007U
#define I2C_SCL_MAIN_STATE_LAST_M  (I2C_SCL_MAIN_STATE_LAST_V << I2C_SCL_MAIN_STATE_LAST_S)
#define I2C_SCL_MAIN_STATE_LAST_V  0x00000007U
#define I2C_SCL_MAIN_STATE_LAST_S  24
/** I2C_SCL_STATE_LAST : RO; bitpos: [30:28]; default: 0;
 *  This field indicates the states of the state machine used to produce SCL.
 *  0: Idle, 1: Start, 2: Negative edge, 3: Low, 4: Positive edge, 5: High, 6: Stop
 */
#define I2C_SCL_STATE_LAST    0x00000007U
#define I2C_SCL_STATE_LAST_M  (I2C_SCL_STATE_LAST_V << I2C_SCL_STATE_LAST_S)
#define I2C_SCL_STATE_LAST_V  0x00000007U
#define I2C_SCL_STATE_LAST_S  28

/** I2C_TO_REG register
 *  Setting time out control for receiving data.
 */
#define I2C_TO_REG(i) (REG_I2C_BASE(i) + 0xc)
/** I2C_TIME_OUT_VALUE : R/W; bitpos: [4:0]; default: 16;
 *  This register is used to configure the timeout for receiving a data bit in APB
 *  clock cycles.
 */
#define I2C_TIME_OUT_VALUE    0x0000001FU
#define I2C_TIME_OUT_VALUE_M  (I2C_TIME_OUT_VALUE_V << I2C_TIME_OUT_VALUE_S)
#define I2C_TIME_OUT_VALUE_V  0x0000001FU
#define I2C_TIME_OUT_VALUE_S  0
/** I2C_TIME_OUT_EN : R/W; bitpos: [5]; default: 0;
 *  This is the enable bit for time out control.
 */
#define I2C_TIME_OUT_EN    (BIT(5))
#define I2C_TIME_OUT_EN_M  (I2C_TIME_OUT_EN_V << I2C_TIME_OUT_EN_S)
#define I2C_TIME_OUT_EN_V  0x00000001U
#define I2C_TIME_OUT_EN_S  5

/** I2C_SLAVE_ADDR_REG register
 *  Local slave address setting
 */
#define I2C_SLAVE_ADDR_REG(i) (REG_I2C_BASE(i) + 0x10)
/** I2C_SLAVE_ADDR : R/W; bitpos: [14:0]; default: 0;
 *  When configured as an I2C Slave, this field is used to configure the slave address.
 */
#define I2C_SLAVE_ADDR    0x00007FFFU
#define I2C_SLAVE_ADDR_M  (I2C_SLAVE_ADDR_V << I2C_SLAVE_ADDR_S)
#define I2C_SLAVE_ADDR_V  0x00007FFFU
#define I2C_SLAVE_ADDR_S  0
/** I2C_ADDR_10BIT_EN : R/W; bitpos: [31]; default: 0;
 *  This field is used to enable the slave 10-bit addressing mode in master mode.
 */
#define I2C_ADDR_10BIT_EN    (BIT(31))
#define I2C_ADDR_10BIT_EN_M  (I2C_ADDR_10BIT_EN_V << I2C_ADDR_10BIT_EN_S)
#define I2C_ADDR_10BIT_EN_V  0x00000001U
#define I2C_ADDR_10BIT_EN_S  31

/** I2C_FIFO_ST_REG register
 *  FIFO status register.
 */
#define I2C_FIFO_ST_REG(i) (REG_I2C_BASE(i) + 0x14)
/** I2C_RXFIFO_RADDR : RO; bitpos: [4:0]; default: 0;
 *  This is the offset address of the APB reading from rxfifo
 */
#define I2C_RXFIFO_RADDR    0x0000001FU
#define I2C_RXFIFO_RADDR_M  (I2C_RXFIFO_RADDR_V << I2C_RXFIFO_RADDR_S)
#define I2C_RXFIFO_RADDR_V  0x0000001FU
#define I2C_RXFIFO_RADDR_S  0
/** I2C_RXFIFO_WADDR : RO; bitpos: [9:5]; default: 0;
 *  This is the offset address of i2c module receiving data and writing to rxfifo.
 */
#define I2C_RXFIFO_WADDR    0x0000001FU
#define I2C_RXFIFO_WADDR_M  (I2C_RXFIFO_WADDR_V << I2C_RXFIFO_WADDR_S)
#define I2C_RXFIFO_WADDR_V  0x0000001FU
#define I2C_RXFIFO_WADDR_S  5
/** I2C_TXFIFO_RADDR : RO; bitpos: [14:10]; default: 0;
 *  This is the offset address of i2c module reading from txfifo.
 */
#define I2C_TXFIFO_RADDR    0x0000001FU
#define I2C_TXFIFO_RADDR_M  (I2C_TXFIFO_RADDR_V << I2C_TXFIFO_RADDR_S)
#define I2C_TXFIFO_RADDR_V  0x0000001FU
#define I2C_TXFIFO_RADDR_S  10
/** I2C_TXFIFO_WADDR : RO; bitpos: [19:15]; default: 0;
 *  This is the offset address of APB bus writing to txfifo.
 */
#define I2C_TXFIFO_WADDR    0x0000001FU
#define I2C_TXFIFO_WADDR_M  (I2C_TXFIFO_WADDR_V << I2C_TXFIFO_WADDR_S)
#define I2C_TXFIFO_WADDR_V  0x0000001FU
#define I2C_TXFIFO_WADDR_S  15
/** I2C_SLAVE_RW_POINT : RO; bitpos: [29:22]; default: 0;
 *  The received data in I2C slave mode.
 */
#define I2C_SLAVE_RW_POINT    0x000000FFU
#define I2C_SLAVE_RW_POINT_M  (I2C_SLAVE_RW_POINT_V << I2C_SLAVE_RW_POINT_S)
#define I2C_SLAVE_RW_POINT_V  0x000000FFU
#define I2C_SLAVE_RW_POINT_S  22

/** I2C_FIFO_CONF_REG register
 *  FIFO configuration register.
 */
#define I2C_FIFO_CONF_REG(i) (REG_I2C_BASE(i) + 0x18)
/** I2C_RXFIFO_WM_THRHD : R/W; bitpos: [4:0]; default: 11;
 *  The water mark threshold of rx FIFO in nonfifo access mode. When
 *  reg_reg_fifo_prt_en is 1 and rx FIFO counter is bigger than
 *  reg_rxfifo_wm_thrhd[4:0], reg_rxfifo_wm_int_raw bit will be valid.
 */
#define I2C_RXFIFO_WM_THRHD    0x0000001FU
#define I2C_RXFIFO_WM_THRHD_M  (I2C_RXFIFO_WM_THRHD_V << I2C_RXFIFO_WM_THRHD_S)
#define I2C_RXFIFO_WM_THRHD_V  0x0000001FU
#define I2C_RXFIFO_WM_THRHD_S  0
/** I2C_TXFIFO_WM_THRHD : R/W; bitpos: [9:5]; default: 4;
 *  The water mark threshold of tx FIFO in nonfifo access mode. When
 *  reg_reg_fifo_prt_en is 1 and tx FIFO counter is smaller than
 *  reg_txfifo_wm_thrhd[4:0], reg_txfifo_wm_int_raw bit will be valid.
 */
#define I2C_TXFIFO_WM_THRHD    0x0000001FU
#define I2C_TXFIFO_WM_THRHD_M  (I2C_TXFIFO_WM_THRHD_V << I2C_TXFIFO_WM_THRHD_S)
#define I2C_TXFIFO_WM_THRHD_V  0x0000001FU
#define I2C_TXFIFO_WM_THRHD_S  5
/** I2C_NONFIFO_EN : R/W; bitpos: [10]; default: 0;
 *  Set this bit to enable APB nonfifo access.
 */
#define I2C_NONFIFO_EN    (BIT(10))
#define I2C_NONFIFO_EN_M  (I2C_NONFIFO_EN_V << I2C_NONFIFO_EN_S)
#define I2C_NONFIFO_EN_V  0x00000001U
#define I2C_NONFIFO_EN_S  10
/** I2C_FIFO_ADDR_CFG_EN : R/W; bitpos: [11]; default: 0;
 *  When this bit is set to 1, the byte received after the I2C address byte represents
 *  the offset address in the I2C Slave RAM.
 */
#define I2C_FIFO_ADDR_CFG_EN    (BIT(11))
#define I2C_FIFO_ADDR_CFG_EN_M  (I2C_FIFO_ADDR_CFG_EN_V << I2C_FIFO_ADDR_CFG_EN_S)
#define I2C_FIFO_ADDR_CFG_EN_V  0x00000001U
#define I2C_FIFO_ADDR_CFG_EN_S  11
/** I2C_RX_FIFO_RST : R/W; bitpos: [12]; default: 0;
 *  Set this bit to reset rx-fifo.
 */
#define I2C_RX_FIFO_RST    (BIT(12))
#define I2C_RX_FIFO_RST_M  (I2C_RX_FIFO_RST_V << I2C_RX_FIFO_RST_S)
#define I2C_RX_FIFO_RST_V  0x00000001U
#define I2C_RX_FIFO_RST_S  12
/** I2C_TX_FIFO_RST : R/W; bitpos: [13]; default: 0;
 *  Set this bit to reset tx-fifo.
 */
#define I2C_TX_FIFO_RST    (BIT(13))
#define I2C_TX_FIFO_RST_M  (I2C_TX_FIFO_RST_V << I2C_TX_FIFO_RST_S)
#define I2C_TX_FIFO_RST_V  0x00000001U
#define I2C_TX_FIFO_RST_S  13
/** I2C_FIFO_PRT_EN : R/W; bitpos: [14]; default: 1;
 *  The control enable bit of FIFO pointer in non-fifo access mode. This bit controls
 *  the valid bits and the interrupts of tx/rx_fifo overflow, underflow, full and empty.
 */
#define I2C_FIFO_PRT_EN    (BIT(14))
#define I2C_FIFO_PRT_EN_M  (I2C_FIFO_PRT_EN_V << I2C_FIFO_PRT_EN_S)
#define I2C_FIFO_PRT_EN_V  0x00000001U
#define I2C_FIFO_PRT_EN_S  14

/** I2C_DATA_REG register
 *  Rx FIFO read data.
 */
#define I2C_DATA_REG(i) (REG_I2C_BASE(i) + 0x1c)
/** I2C_FIFO_RDATA : HRO; bitpos: [7:0]; default: 0;
 *  The value of rx FIFO read data.
 */
#define I2C_FIFO_RDATA    0x000000FFU
#define I2C_FIFO_RDATA_M  (I2C_FIFO_RDATA_V << I2C_FIFO_RDATA_S)
#define I2C_FIFO_RDATA_V  0x000000FFU
#define I2C_FIFO_RDATA_S  0

/** I2C_INT_RAW_REG register
 *  Raw interrupt status
 */
#define I2C_INT_RAW_REG(i) (REG_I2C_BASE(i) + 0x20)
/** I2C_RXFIFO_WM_INT_RAW : R/SS/WTC; bitpos: [0]; default: 0;
 *  The raw interrupt bit for I2C_RXFIFO_WM_INT interrupt.
 */
#define I2C_RXFIFO_WM_INT_RAW    (BIT(0))
#define I2C_RXFIFO_WM_INT_RAW_M  (I2C_RXFIFO_WM_INT_RAW_V << I2C_RXFIFO_WM_INT_RAW_S)
#define I2C_RXFIFO_WM_INT_RAW_V  0x00000001U
#define I2C_RXFIFO_WM_INT_RAW_S  0
/** I2C_TXFIFO_WM_INT_RAW : R/SS/WTC; bitpos: [1]; default: 1;
 *  The raw interrupt bit for I2C_TXFIFO_WM_INT interrupt.
 */
#define I2C_TXFIFO_WM_INT_RAW    (BIT(1))
#define I2C_TXFIFO_WM_INT_RAW_M  (I2C_TXFIFO_WM_INT_RAW_V << I2C_TXFIFO_WM_INT_RAW_S)
#define I2C_TXFIFO_WM_INT_RAW_V  0x00000001U
#define I2C_TXFIFO_WM_INT_RAW_S  1
/** I2C_RXFIFO_OVF_INT_RAW : R/SS/WTC; bitpos: [2]; default: 0;
 *  The raw interrupt bit for I2C_RXFIFO_OVF_INT interrupt.
 */
#define I2C_RXFIFO_OVF_INT_RAW    (BIT(2))
#define I2C_RXFIFO_OVF_INT_RAW_M  (I2C_RXFIFO_OVF_INT_RAW_V << I2C_RXFIFO_OVF_INT_RAW_S)
#define I2C_RXFIFO_OVF_INT_RAW_V  0x00000001U
#define I2C_RXFIFO_OVF_INT_RAW_S  2
/** I2C_END_DETECT_INT_RAW : R/SS/WTC; bitpos: [3]; default: 0;
 *  The raw interrupt bit for the I2C_END_DETECT_INT interrupt.
 */
#define I2C_END_DETECT_INT_RAW    (BIT(3))
#define I2C_END_DETECT_INT_RAW_M  (I2C_END_DETECT_INT_RAW_V << I2C_END_DETECT_INT_RAW_S)
#define I2C_END_DETECT_INT_RAW_V  0x00000001U
#define I2C_END_DETECT_INT_RAW_S  3
/** I2C_BYTE_TRANS_DONE_INT_RAW : R/SS/WTC; bitpos: [4]; default: 0;
 *  The raw interrupt bit for the I2C_END_DETECT_INT interrupt.
 */
#define I2C_BYTE_TRANS_DONE_INT_RAW    (BIT(4))
#define I2C_BYTE_TRANS_DONE_INT_RAW_M  (I2C_BYTE_TRANS_DONE_INT_RAW_V << I2C_BYTE_TRANS_DONE_INT_RAW_S)
#define I2C_BYTE_TRANS_DONE_INT_RAW_V  0x00000001U
#define I2C_BYTE_TRANS_DONE_INT_RAW_S  4
/** I2C_ARBITRATION_LOST_INT_RAW : R/SS/WTC; bitpos: [5]; default: 0;
 *  The raw interrupt bit for the I2C_ARBITRATION_LOST_INT interrupt.
 */
#define I2C_ARBITRATION_LOST_INT_RAW    (BIT(5))
#define I2C_ARBITRATION_LOST_INT_RAW_M  (I2C_ARBITRATION_LOST_INT_RAW_V << I2C_ARBITRATION_LOST_INT_RAW_S)
#define I2C_ARBITRATION_LOST_INT_RAW_V  0x00000001U
#define I2C_ARBITRATION_LOST_INT_RAW_S  5
/** I2C_MST_TXFIFO_UDF_INT_RAW : R/SS/WTC; bitpos: [6]; default: 0;
 *  The raw interrupt bit for I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_MST_TXFIFO_UDF_INT_RAW    (BIT(6))
#define I2C_MST_TXFIFO_UDF_INT_RAW_M  (I2C_MST_TXFIFO_UDF_INT_RAW_V << I2C_MST_TXFIFO_UDF_INT_RAW_S)
#define I2C_MST_TXFIFO_UDF_INT_RAW_V  0x00000001U
#define I2C_MST_TXFIFO_UDF_INT_RAW_S  6
/** I2C_TRANS_COMPLETE_INT_RAW : R/SS/WTC; bitpos: [7]; default: 0;
 *  The raw interrupt bit for the I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_TRANS_COMPLETE_INT_RAW    (BIT(7))
#define I2C_TRANS_COMPLETE_INT_RAW_M  (I2C_TRANS_COMPLETE_INT_RAW_V << I2C_TRANS_COMPLETE_INT_RAW_S)
#define I2C_TRANS_COMPLETE_INT_RAW_V  0x00000001U
#define I2C_TRANS_COMPLETE_INT_RAW_S  7
/** I2C_TIME_OUT_INT_RAW : R/SS/WTC; bitpos: [8]; default: 0;
 *  The raw interrupt bit for the I2C_TIME_OUT_INT interrupt.
 */
#define I2C_TIME_OUT_INT_RAW    (BIT(8))
#define I2C_TIME_OUT_INT_RAW_M  (I2C_TIME_OUT_INT_RAW_V << I2C_TIME_OUT_INT_RAW_S)
#define I2C_TIME_OUT_INT_RAW_V  0x00000001U
#define I2C_TIME_OUT_INT_RAW_S  8
/** I2C_TRANS_START_INT_RAW : R/SS/WTC; bitpos: [9]; default: 0;
 *  The raw interrupt bit for the I2C_TRANS_START_INT interrupt.
 */
#define I2C_TRANS_START_INT_RAW    (BIT(9))
#define I2C_TRANS_START_INT_RAW_M  (I2C_TRANS_START_INT_RAW_V << I2C_TRANS_START_INT_RAW_S)
#define I2C_TRANS_START_INT_RAW_V  0x00000001U
#define I2C_TRANS_START_INT_RAW_S  9
/** I2C_NACK_INT_RAW : R/SS/WTC; bitpos: [10]; default: 0;
 *  The raw interrupt bit for I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_NACK_INT_RAW    (BIT(10))
#define I2C_NACK_INT_RAW_M  (I2C_NACK_INT_RAW_V << I2C_NACK_INT_RAW_S)
#define I2C_NACK_INT_RAW_V  0x00000001U
#define I2C_NACK_INT_RAW_S  10
/** I2C_TXFIFO_OVF_INT_RAW : R/SS/WTC; bitpos: [11]; default: 0;
 *  The raw interrupt bit for I2C_TXFIFO_OVF_INT interrupt.
 */
#define I2C_TXFIFO_OVF_INT_RAW    (BIT(11))
#define I2C_TXFIFO_OVF_INT_RAW_M  (I2C_TXFIFO_OVF_INT_RAW_V << I2C_TXFIFO_OVF_INT_RAW_S)
#define I2C_TXFIFO_OVF_INT_RAW_V  0x00000001U
#define I2C_TXFIFO_OVF_INT_RAW_S  11
/** I2C_RXFIFO_UDF_INT_RAW : R/SS/WTC; bitpos: [12]; default: 0;
 *  The raw interrupt bit for I2C_RXFIFO_UDF_INT  interrupt.
 */
#define I2C_RXFIFO_UDF_INT_RAW    (BIT(12))
#define I2C_RXFIFO_UDF_INT_RAW_M  (I2C_RXFIFO_UDF_INT_RAW_V << I2C_RXFIFO_UDF_INT_RAW_S)
#define I2C_RXFIFO_UDF_INT_RAW_V  0x00000001U
#define I2C_RXFIFO_UDF_INT_RAW_S  12
/** I2C_SCL_ST_TO_INT_RAW : R/SS/WTC; bitpos: [13]; default: 0;
 *  The raw interrupt bit for I2C_SCL_ST_TO_INT interrupt.
 */
#define I2C_SCL_ST_TO_INT_RAW    (BIT(13))
#define I2C_SCL_ST_TO_INT_RAW_M  (I2C_SCL_ST_TO_INT_RAW_V << I2C_SCL_ST_TO_INT_RAW_S)
#define I2C_SCL_ST_TO_INT_RAW_V  0x00000001U
#define I2C_SCL_ST_TO_INT_RAW_S  13
/** I2C_SCL_MAIN_ST_TO_INT_RAW : R/SS/WTC; bitpos: [14]; default: 0;
 *  The raw interrupt bit for I2C_SCL_MAIN_ST_TO_INT interrupt.
 */
#define I2C_SCL_MAIN_ST_TO_INT_RAW    (BIT(14))
#define I2C_SCL_MAIN_ST_TO_INT_RAW_M  (I2C_SCL_MAIN_ST_TO_INT_RAW_V << I2C_SCL_MAIN_ST_TO_INT_RAW_S)
#define I2C_SCL_MAIN_ST_TO_INT_RAW_V  0x00000001U
#define I2C_SCL_MAIN_ST_TO_INT_RAW_S  14
/** I2C_DET_START_INT_RAW : R/SS/WTC; bitpos: [15]; default: 0;
 *  The raw interrupt bit for I2C_DET_START_INT interrupt.
 */
#define I2C_DET_START_INT_RAW    (BIT(15))
#define I2C_DET_START_INT_RAW_M  (I2C_DET_START_INT_RAW_V << I2C_DET_START_INT_RAW_S)
#define I2C_DET_START_INT_RAW_V  0x00000001U
#define I2C_DET_START_INT_RAW_S  15
/** I2C_SLAVE_STRETCH_INT_RAW : R/SS/WTC; bitpos: [16]; default: 0;
 *  The raw interrupt bit for I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_SLAVE_STRETCH_INT_RAW    (BIT(16))
#define I2C_SLAVE_STRETCH_INT_RAW_M  (I2C_SLAVE_STRETCH_INT_RAW_V << I2C_SLAVE_STRETCH_INT_RAW_S)
#define I2C_SLAVE_STRETCH_INT_RAW_V  0x00000001U
#define I2C_SLAVE_STRETCH_INT_RAW_S  16
/** I2C_GENERAL_CALL_INT_RAW : R/SS/WTC; bitpos: [17]; default: 0;
 *  The raw interrupt bit for I2C_GENARAL_CALL_INT interrupt.
 */
#define I2C_GENERAL_CALL_INT_RAW    (BIT(17))
#define I2C_GENERAL_CALL_INT_RAW_M  (I2C_GENERAL_CALL_INT_RAW_V << I2C_GENERAL_CALL_INT_RAW_S)
#define I2C_GENERAL_CALL_INT_RAW_V  0x00000001U
#define I2C_GENERAL_CALL_INT_RAW_S  17
/** I2C_SLAVE_ADDR_UNMATCH_INT_RAW : R/SS/WTC; bitpos: [18]; default: 0;
 *  The raw interrupt bit for I2C_SLAVE_ADDR_UNMATCH_INT_RAW interrupt.
 */
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW    (BIT(18))
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW_M  (I2C_SLAVE_ADDR_UNMATCH_INT_RAW_V << I2C_SLAVE_ADDR_UNMATCH_INT_RAW_S)
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW_V  0x00000001U
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW_S  18

/** I2C_INT_CLR_REG register
 *  Interrupt clear bits
 */
#define I2C_INT_CLR_REG(i) (REG_I2C_BASE(i) + 0x24)
/** I2C_RXFIFO_WM_INT_CLR : WT; bitpos: [0]; default: 0;
 *  Set this bit to clear I2C_RXFIFO_WM_INT interrupt.
 */
#define I2C_RXFIFO_WM_INT_CLR    (BIT(0))
#define I2C_RXFIFO_WM_INT_CLR_M  (I2C_RXFIFO_WM_INT_CLR_V << I2C_RXFIFO_WM_INT_CLR_S)
#define I2C_RXFIFO_WM_INT_CLR_V  0x00000001U
#define I2C_RXFIFO_WM_INT_CLR_S  0
/** I2C_TXFIFO_WM_INT_CLR : WT; bitpos: [1]; default: 0;
 *  Set this bit to clear I2C_TXFIFO_WM_INT interrupt.
 */
#define I2C_TXFIFO_WM_INT_CLR    (BIT(1))
#define I2C_TXFIFO_WM_INT_CLR_M  (I2C_TXFIFO_WM_INT_CLR_V << I2C_TXFIFO_WM_INT_CLR_S)
#define I2C_TXFIFO_WM_INT_CLR_V  0x00000001U
#define I2C_TXFIFO_WM_INT_CLR_S  1
/** I2C_RXFIFO_OVF_INT_CLR : WT; bitpos: [2]; default: 0;
 *  Set this bit to clear I2C_RXFIFO_OVF_INT interrupt.
 */
#define I2C_RXFIFO_OVF_INT_CLR    (BIT(2))
#define I2C_RXFIFO_OVF_INT_CLR_M  (I2C_RXFIFO_OVF_INT_CLR_V << I2C_RXFIFO_OVF_INT_CLR_S)
#define I2C_RXFIFO_OVF_INT_CLR_V  0x00000001U
#define I2C_RXFIFO_OVF_INT_CLR_S  2
/** I2C_END_DETECT_INT_CLR : WT; bitpos: [3]; default: 0;
 *  Set this bit to clear the I2C_END_DETECT_INT interrupt.
 */
#define I2C_END_DETECT_INT_CLR    (BIT(3))
#define I2C_END_DETECT_INT_CLR_M  (I2C_END_DETECT_INT_CLR_V << I2C_END_DETECT_INT_CLR_S)
#define I2C_END_DETECT_INT_CLR_V  0x00000001U
#define I2C_END_DETECT_INT_CLR_S  3
/** I2C_BYTE_TRANS_DONE_INT_CLR : WT; bitpos: [4]; default: 0;
 *  Set this bit to clear the I2C_END_DETECT_INT interrupt.
 */
#define I2C_BYTE_TRANS_DONE_INT_CLR    (BIT(4))
#define I2C_BYTE_TRANS_DONE_INT_CLR_M  (I2C_BYTE_TRANS_DONE_INT_CLR_V << I2C_BYTE_TRANS_DONE_INT_CLR_S)
#define I2C_BYTE_TRANS_DONE_INT_CLR_V  0x00000001U
#define I2C_BYTE_TRANS_DONE_INT_CLR_S  4
/** I2C_ARBITRATION_LOST_INT_CLR : WT; bitpos: [5]; default: 0;
 *  Set this bit to clear the I2C_ARBITRATION_LOST_INT interrupt.
 */
#define I2C_ARBITRATION_LOST_INT_CLR    (BIT(5))
#define I2C_ARBITRATION_LOST_INT_CLR_M  (I2C_ARBITRATION_LOST_INT_CLR_V << I2C_ARBITRATION_LOST_INT_CLR_S)
#define I2C_ARBITRATION_LOST_INT_CLR_V  0x00000001U
#define I2C_ARBITRATION_LOST_INT_CLR_S  5
/** I2C_MST_TXFIFO_UDF_INT_CLR : WT; bitpos: [6]; default: 0;
 *  Set this bit to clear I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_MST_TXFIFO_UDF_INT_CLR    (BIT(6))
#define I2C_MST_TXFIFO_UDF_INT_CLR_M  (I2C_MST_TXFIFO_UDF_INT_CLR_V << I2C_MST_TXFIFO_UDF_INT_CLR_S)
#define I2C_MST_TXFIFO_UDF_INT_CLR_V  0x00000001U
#define I2C_MST_TXFIFO_UDF_INT_CLR_S  6
/** I2C_TRANS_COMPLETE_INT_CLR : WT; bitpos: [7]; default: 0;
 *  Set this bit to clear the I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_TRANS_COMPLETE_INT_CLR    (BIT(7))
#define I2C_TRANS_COMPLETE_INT_CLR_M  (I2C_TRANS_COMPLETE_INT_CLR_V << I2C_TRANS_COMPLETE_INT_CLR_S)
#define I2C_TRANS_COMPLETE_INT_CLR_V  0x00000001U
#define I2C_TRANS_COMPLETE_INT_CLR_S  7
/** I2C_TIME_OUT_INT_CLR : WT; bitpos: [8]; default: 0;
 *  Set this bit to clear the I2C_TIME_OUT_INT interrupt.
 */
#define I2C_TIME_OUT_INT_CLR    (BIT(8))
#define I2C_TIME_OUT_INT_CLR_M  (I2C_TIME_OUT_INT_CLR_V << I2C_TIME_OUT_INT_CLR_S)
#define I2C_TIME_OUT_INT_CLR_V  0x00000001U
#define I2C_TIME_OUT_INT_CLR_S  8
/** I2C_TRANS_START_INT_CLR : WT; bitpos: [9]; default: 0;
 *  Set this bit to clear the I2C_TRANS_START_INT interrupt.
 */
#define I2C_TRANS_START_INT_CLR    (BIT(9))
#define I2C_TRANS_START_INT_CLR_M  (I2C_TRANS_START_INT_CLR_V << I2C_TRANS_START_INT_CLR_S)
#define I2C_TRANS_START_INT_CLR_V  0x00000001U
#define I2C_TRANS_START_INT_CLR_S  9
/** I2C_NACK_INT_CLR : WT; bitpos: [10]; default: 0;
 *  Set this bit to clear I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_NACK_INT_CLR    (BIT(10))
#define I2C_NACK_INT_CLR_M  (I2C_NACK_INT_CLR_V << I2C_NACK_INT_CLR_S)
#define I2C_NACK_INT_CLR_V  0x00000001U
#define I2C_NACK_INT_CLR_S  10
/** I2C_TXFIFO_OVF_INT_CLR : WT; bitpos: [11]; default: 0;
 *  Set this bit to clear I2C_TXFIFO_OVF_INT interrupt.
 */
#define I2C_TXFIFO_OVF_INT_CLR    (BIT(11))
#define I2C_TXFIFO_OVF_INT_CLR_M  (I2C_TXFIFO_OVF_INT_CLR_V << I2C_TXFIFO_OVF_INT_CLR_S)
#define I2C_TXFIFO_OVF_INT_CLR_V  0x00000001U
#define I2C_TXFIFO_OVF_INT_CLR_S  11
/** I2C_RXFIFO_UDF_INT_CLR : WT; bitpos: [12]; default: 0;
 *  Set this bit to clear I2C_RXFIFO_UDF_INT  interrupt.
 */
#define I2C_RXFIFO_UDF_INT_CLR    (BIT(12))
#define I2C_RXFIFO_UDF_INT_CLR_M  (I2C_RXFIFO_UDF_INT_CLR_V << I2C_RXFIFO_UDF_INT_CLR_S)
#define I2C_RXFIFO_UDF_INT_CLR_V  0x00000001U
#define I2C_RXFIFO_UDF_INT_CLR_S  12
/** I2C_SCL_ST_TO_INT_CLR : WT; bitpos: [13]; default: 0;
 *  Set this bit to clear I2C_SCL_ST_TO_INT interrupt.
 */
#define I2C_SCL_ST_TO_INT_CLR    (BIT(13))
#define I2C_SCL_ST_TO_INT_CLR_M  (I2C_SCL_ST_TO_INT_CLR_V << I2C_SCL_ST_TO_INT_CLR_S)
#define I2C_SCL_ST_TO_INT_CLR_V  0x00000001U
#define I2C_SCL_ST_TO_INT_CLR_S  13
/** I2C_SCL_MAIN_ST_TO_INT_CLR : WT; bitpos: [14]; default: 0;
 *  Set this bit to clear I2C_SCL_MAIN_ST_TO_INT interrupt.
 */
#define I2C_SCL_MAIN_ST_TO_INT_CLR    (BIT(14))
#define I2C_SCL_MAIN_ST_TO_INT_CLR_M  (I2C_SCL_MAIN_ST_TO_INT_CLR_V << I2C_SCL_MAIN_ST_TO_INT_CLR_S)
#define I2C_SCL_MAIN_ST_TO_INT_CLR_V  0x00000001U
#define I2C_SCL_MAIN_ST_TO_INT_CLR_S  14
/** I2C_DET_START_INT_CLR : WT; bitpos: [15]; default: 0;
 *  Set this bit to clear I2C_DET_START_INT interrupt.
 */
#define I2C_DET_START_INT_CLR    (BIT(15))
#define I2C_DET_START_INT_CLR_M  (I2C_DET_START_INT_CLR_V << I2C_DET_START_INT_CLR_S)
#define I2C_DET_START_INT_CLR_V  0x00000001U
#define I2C_DET_START_INT_CLR_S  15
/** I2C_SLAVE_STRETCH_INT_CLR : WT; bitpos: [16]; default: 0;
 *  Set this bit to clear I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_SLAVE_STRETCH_INT_CLR    (BIT(16))
#define I2C_SLAVE_STRETCH_INT_CLR_M  (I2C_SLAVE_STRETCH_INT_CLR_V << I2C_SLAVE_STRETCH_INT_CLR_S)
#define I2C_SLAVE_STRETCH_INT_CLR_V  0x00000001U
#define I2C_SLAVE_STRETCH_INT_CLR_S  16
/** I2C_GENERAL_CALL_INT_CLR : WT; bitpos: [17]; default: 0;
 *  Set this bit to clear I2C_GENARAL_CALL_INT interrupt.
 */
#define I2C_GENERAL_CALL_INT_CLR    (BIT(17))
#define I2C_GENERAL_CALL_INT_CLR_M  (I2C_GENERAL_CALL_INT_CLR_V << I2C_GENERAL_CALL_INT_CLR_S)
#define I2C_GENERAL_CALL_INT_CLR_V  0x00000001U
#define I2C_GENERAL_CALL_INT_CLR_S  17
/** I2C_SLAVE_ADDR_UNMATCH_INT_CLR : WT; bitpos: [18]; default: 0;
 *  Set this bit to clear I2C_SLAVE_ADDR_UNMATCH_INT_RAW interrupt.
 */
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR    (BIT(18))
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR_M  (I2C_SLAVE_ADDR_UNMATCH_INT_CLR_V << I2C_SLAVE_ADDR_UNMATCH_INT_CLR_S)
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR_V  0x00000001U
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR_S  18

/** I2C_INT_ENA_REG register
 *  Interrupt enable bits
 */
#define I2C_INT_ENA_REG(i) (REG_I2C_BASE(i) + 0x28)
/** I2C_RXFIFO_WM_INT_ENA : R/W; bitpos: [0]; default: 0;
 *  The interrupt enable bit for I2C_RXFIFO_WM_INT interrupt.
 */
#define I2C_RXFIFO_WM_INT_ENA    (BIT(0))
#define I2C_RXFIFO_WM_INT_ENA_M  (I2C_RXFIFO_WM_INT_ENA_V << I2C_RXFIFO_WM_INT_ENA_S)
#define I2C_RXFIFO_WM_INT_ENA_V  0x00000001U
#define I2C_RXFIFO_WM_INT_ENA_S  0
/** I2C_TXFIFO_WM_INT_ENA : R/W; bitpos: [1]; default: 0;
 *  The interrupt enable bit for I2C_TXFIFO_WM_INT interrupt.
 */
#define I2C_TXFIFO_WM_INT_ENA    (BIT(1))
#define I2C_TXFIFO_WM_INT_ENA_M  (I2C_TXFIFO_WM_INT_ENA_V << I2C_TXFIFO_WM_INT_ENA_S)
#define I2C_TXFIFO_WM_INT_ENA_V  0x00000001U
#define I2C_TXFIFO_WM_INT_ENA_S  1
/** I2C_RXFIFO_OVF_INT_ENA : R/W; bitpos: [2]; default: 0;
 *  The interrupt enable bit for I2C_RXFIFO_OVF_INT interrupt.
 */
#define I2C_RXFIFO_OVF_INT_ENA    (BIT(2))
#define I2C_RXFIFO_OVF_INT_ENA_M  (I2C_RXFIFO_OVF_INT_ENA_V << I2C_RXFIFO_OVF_INT_ENA_S)
#define I2C_RXFIFO_OVF_INT_ENA_V  0x00000001U
#define I2C_RXFIFO_OVF_INT_ENA_S  2
/** I2C_END_DETECT_INT_ENA : R/W; bitpos: [3]; default: 0;
 *  The interrupt enable bit for the I2C_END_DETECT_INT interrupt.
 */
#define I2C_END_DETECT_INT_ENA    (BIT(3))
#define I2C_END_DETECT_INT_ENA_M  (I2C_END_DETECT_INT_ENA_V << I2C_END_DETECT_INT_ENA_S)
#define I2C_END_DETECT_INT_ENA_V  0x00000001U
#define I2C_END_DETECT_INT_ENA_S  3
/** I2C_BYTE_TRANS_DONE_INT_ENA : R/W; bitpos: [4]; default: 0;
 *  The interrupt enable bit for the I2C_END_DETECT_INT interrupt.
 */
#define I2C_BYTE_TRANS_DONE_INT_ENA    (BIT(4))
#define I2C_BYTE_TRANS_DONE_INT_ENA_M  (I2C_BYTE_TRANS_DONE_INT_ENA_V << I2C_BYTE_TRANS_DONE_INT_ENA_S)
#define I2C_BYTE_TRANS_DONE_INT_ENA_V  0x00000001U
#define I2C_BYTE_TRANS_DONE_INT_ENA_S  4
/** I2C_ARBITRATION_LOST_INT_ENA : R/W; bitpos: [5]; default: 0;
 *  The interrupt enable bit for the I2C_ARBITRATION_LOST_INT interrupt.
 */
#define I2C_ARBITRATION_LOST_INT_ENA    (BIT(5))
#define I2C_ARBITRATION_LOST_INT_ENA_M  (I2C_ARBITRATION_LOST_INT_ENA_V << I2C_ARBITRATION_LOST_INT_ENA_S)
#define I2C_ARBITRATION_LOST_INT_ENA_V  0x00000001U
#define I2C_ARBITRATION_LOST_INT_ENA_S  5
/** I2C_MST_TXFIFO_UDF_INT_ENA : R/W; bitpos: [6]; default: 0;
 *  The interrupt enable bit for I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_MST_TXFIFO_UDF_INT_ENA    (BIT(6))
#define I2C_MST_TXFIFO_UDF_INT_ENA_M  (I2C_MST_TXFIFO_UDF_INT_ENA_V << I2C_MST_TXFIFO_UDF_INT_ENA_S)
#define I2C_MST_TXFIFO_UDF_INT_ENA_V  0x00000001U
#define I2C_MST_TXFIFO_UDF_INT_ENA_S  6
/** I2C_TRANS_COMPLETE_INT_ENA : R/W; bitpos: [7]; default: 0;
 *  The interrupt enable bit for the I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_TRANS_COMPLETE_INT_ENA    (BIT(7))
#define I2C_TRANS_COMPLETE_INT_ENA_M  (I2C_TRANS_COMPLETE_INT_ENA_V << I2C_TRANS_COMPLETE_INT_ENA_S)
#define I2C_TRANS_COMPLETE_INT_ENA_V  0x00000001U
#define I2C_TRANS_COMPLETE_INT_ENA_S  7
/** I2C_TIME_OUT_INT_ENA : R/W; bitpos: [8]; default: 0;
 *  The interrupt enable bit for the I2C_TIME_OUT_INT interrupt.
 */
#define I2C_TIME_OUT_INT_ENA    (BIT(8))
#define I2C_TIME_OUT_INT_ENA_M  (I2C_TIME_OUT_INT_ENA_V << I2C_TIME_OUT_INT_ENA_S)
#define I2C_TIME_OUT_INT_ENA_V  0x00000001U
#define I2C_TIME_OUT_INT_ENA_S  8
/** I2C_TRANS_START_INT_ENA : R/W; bitpos: [9]; default: 0;
 *  The interrupt enable bit for the I2C_TRANS_START_INT interrupt.
 */
#define I2C_TRANS_START_INT_ENA    (BIT(9))
#define I2C_TRANS_START_INT_ENA_M  (I2C_TRANS_START_INT_ENA_V << I2C_TRANS_START_INT_ENA_S)
#define I2C_TRANS_START_INT_ENA_V  0x00000001U
#define I2C_TRANS_START_INT_ENA_S  9
/** I2C_NACK_INT_ENA : R/W; bitpos: [10]; default: 0;
 *  The interrupt enable bit for I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_NACK_INT_ENA    (BIT(10))
#define I2C_NACK_INT_ENA_M  (I2C_NACK_INT_ENA_V << I2C_NACK_INT_ENA_S)
#define I2C_NACK_INT_ENA_V  0x00000001U
#define I2C_NACK_INT_ENA_S  10
/** I2C_TXFIFO_OVF_INT_ENA : R/W; bitpos: [11]; default: 0;
 *  The interrupt enable bit for I2C_TXFIFO_OVF_INT interrupt.
 */
#define I2C_TXFIFO_OVF_INT_ENA    (BIT(11))
#define I2C_TXFIFO_OVF_INT_ENA_M  (I2C_TXFIFO_OVF_INT_ENA_V << I2C_TXFIFO_OVF_INT_ENA_S)
#define I2C_TXFIFO_OVF_INT_ENA_V  0x00000001U
#define I2C_TXFIFO_OVF_INT_ENA_S  11
/** I2C_RXFIFO_UDF_INT_ENA : R/W; bitpos: [12]; default: 0;
 *  The interrupt enable bit for I2C_RXFIFO_UDF_INT  interrupt.
 */
#define I2C_RXFIFO_UDF_INT_ENA    (BIT(12))
#define I2C_RXFIFO_UDF_INT_ENA_M  (I2C_RXFIFO_UDF_INT_ENA_V << I2C_RXFIFO_UDF_INT_ENA_S)
#define I2C_RXFIFO_UDF_INT_ENA_V  0x00000001U
#define I2C_RXFIFO_UDF_INT_ENA_S  12
/** I2C_SCL_ST_TO_INT_ENA : R/W; bitpos: [13]; default: 0;
 *  The interrupt enable bit for I2C_SCL_ST_TO_INT interrupt.
 */
#define I2C_SCL_ST_TO_INT_ENA    (BIT(13))
#define I2C_SCL_ST_TO_INT_ENA_M  (I2C_SCL_ST_TO_INT_ENA_V << I2C_SCL_ST_TO_INT_ENA_S)
#define I2C_SCL_ST_TO_INT_ENA_V  0x00000001U
#define I2C_SCL_ST_TO_INT_ENA_S  13
/** I2C_SCL_MAIN_ST_TO_INT_ENA : R/W; bitpos: [14]; default: 0;
 *  The interrupt enable bit for I2C_SCL_MAIN_ST_TO_INT interrupt.
 */
#define I2C_SCL_MAIN_ST_TO_INT_ENA    (BIT(14))
#define I2C_SCL_MAIN_ST_TO_INT_ENA_M  (I2C_SCL_MAIN_ST_TO_INT_ENA_V << I2C_SCL_MAIN_ST_TO_INT_ENA_S)
#define I2C_SCL_MAIN_ST_TO_INT_ENA_V  0x00000001U
#define I2C_SCL_MAIN_ST_TO_INT_ENA_S  14
/** I2C_DET_START_INT_ENA : R/W; bitpos: [15]; default: 0;
 *  The interrupt enable bit for I2C_DET_START_INT interrupt.
 */
#define I2C_DET_START_INT_ENA    (BIT(15))
#define I2C_DET_START_INT_ENA_M  (I2C_DET_START_INT_ENA_V << I2C_DET_START_INT_ENA_S)
#define I2C_DET_START_INT_ENA_V  0x00000001U
#define I2C_DET_START_INT_ENA_S  15
/** I2C_SLAVE_STRETCH_INT_ENA : R/W; bitpos: [16]; default: 0;
 *  The interrupt enable bit for I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_SLAVE_STRETCH_INT_ENA    (BIT(16))
#define I2C_SLAVE_STRETCH_INT_ENA_M  (I2C_SLAVE_STRETCH_INT_ENA_V << I2C_SLAVE_STRETCH_INT_ENA_S)
#define I2C_SLAVE_STRETCH_INT_ENA_V  0x00000001U
#define I2C_SLAVE_STRETCH_INT_ENA_S  16
/** I2C_GENERAL_CALL_INT_ENA : R/W; bitpos: [17]; default: 0;
 *  The interrupt enable bit for I2C_GENARAL_CALL_INT interrupt.
 */
#define I2C_GENERAL_CALL_INT_ENA    (BIT(17))
#define I2C_GENERAL_CALL_INT_ENA_M  (I2C_GENERAL_CALL_INT_ENA_V << I2C_GENERAL_CALL_INT_ENA_S)
#define I2C_GENERAL_CALL_INT_ENA_V  0x00000001U
#define I2C_GENERAL_CALL_INT_ENA_S  17
/** I2C_SLAVE_ADDR_UNMATCH_INT_ENA : R/W; bitpos: [18]; default: 0;
 *  The interrupt enable bit for I2C_SLAVE_ADDR_UNMATCH_INT interrupt.
 */
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA    (BIT(18))
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA_M  (I2C_SLAVE_ADDR_UNMATCH_INT_ENA_V << I2C_SLAVE_ADDR_UNMATCH_INT_ENA_S)
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA_V  0x00000001U
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA_S  18

/** I2C_INT_STATUS_REG register
 *  Status of captured I2C communication events
 */
#define I2C_INT_STATUS_REG(i) (REG_I2C_BASE(i) + 0x2c)
/** I2C_RXFIFO_WM_INT_ST : RO; bitpos: [0]; default: 0;
 *  The masked interrupt status bit for I2C_RXFIFO_WM_INT interrupt.
 */
#define I2C_RXFIFO_WM_INT_ST    (BIT(0))
#define I2C_RXFIFO_WM_INT_ST_M  (I2C_RXFIFO_WM_INT_ST_V << I2C_RXFIFO_WM_INT_ST_S)
#define I2C_RXFIFO_WM_INT_ST_V  0x00000001U
#define I2C_RXFIFO_WM_INT_ST_S  0
/** I2C_TXFIFO_WM_INT_ST : RO; bitpos: [1]; default: 0;
 *  The masked interrupt status bit for I2C_TXFIFO_WM_INT interrupt.
 */
#define I2C_TXFIFO_WM_INT_ST    (BIT(1))
#define I2C_TXFIFO_WM_INT_ST_M  (I2C_TXFIFO_WM_INT_ST_V << I2C_TXFIFO_WM_INT_ST_S)
#define I2C_TXFIFO_WM_INT_ST_V  0x00000001U
#define I2C_TXFIFO_WM_INT_ST_S  1
/** I2C_RXFIFO_OVF_INT_ST : RO; bitpos: [2]; default: 0;
 *  The masked interrupt status bit for I2C_RXFIFO_OVF_INT interrupt.
 */
#define I2C_RXFIFO_OVF_INT_ST    (BIT(2))
#define I2C_RXFIFO_OVF_INT_ST_M  (I2C_RXFIFO_OVF_INT_ST_V << I2C_RXFIFO_OVF_INT_ST_S)
#define I2C_RXFIFO_OVF_INT_ST_V  0x00000001U
#define I2C_RXFIFO_OVF_INT_ST_S  2
/** I2C_END_DETECT_INT_ST : RO; bitpos: [3]; default: 0;
 *  The masked interrupt status bit for the I2C_END_DETECT_INT interrupt.
 */
#define I2C_END_DETECT_INT_ST    (BIT(3))
#define I2C_END_DETECT_INT_ST_M  (I2C_END_DETECT_INT_ST_V << I2C_END_DETECT_INT_ST_S)
#define I2C_END_DETECT_INT_ST_V  0x00000001U
#define I2C_END_DETECT_INT_ST_S  3
/** I2C_BYTE_TRANS_DONE_INT_ST : RO; bitpos: [4]; default: 0;
 *  The masked interrupt status bit for the I2C_END_DETECT_INT interrupt.
 */
#define I2C_BYTE_TRANS_DONE_INT_ST    (BIT(4))
#define I2C_BYTE_TRANS_DONE_INT_ST_M  (I2C_BYTE_TRANS_DONE_INT_ST_V << I2C_BYTE_TRANS_DONE_INT_ST_S)
#define I2C_BYTE_TRANS_DONE_INT_ST_V  0x00000001U
#define I2C_BYTE_TRANS_DONE_INT_ST_S  4
/** I2C_ARBITRATION_LOST_INT_ST : RO; bitpos: [5]; default: 0;
 *  The masked interrupt status bit for the I2C_ARBITRATION_LOST_INT interrupt.
 */
#define I2C_ARBITRATION_LOST_INT_ST    (BIT(5))
#define I2C_ARBITRATION_LOST_INT_ST_M  (I2C_ARBITRATION_LOST_INT_ST_V << I2C_ARBITRATION_LOST_INT_ST_S)
#define I2C_ARBITRATION_LOST_INT_ST_V  0x00000001U
#define I2C_ARBITRATION_LOST_INT_ST_S  5
/** I2C_MST_TXFIFO_UDF_INT_ST : RO; bitpos: [6]; default: 0;
 *  The masked interrupt status bit for I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_MST_TXFIFO_UDF_INT_ST    (BIT(6))
#define I2C_MST_TXFIFO_UDF_INT_ST_M  (I2C_MST_TXFIFO_UDF_INT_ST_V << I2C_MST_TXFIFO_UDF_INT_ST_S)
#define I2C_MST_TXFIFO_UDF_INT_ST_V  0x00000001U
#define I2C_MST_TXFIFO_UDF_INT_ST_S  6
/** I2C_TRANS_COMPLETE_INT_ST : RO; bitpos: [7]; default: 0;
 *  The masked interrupt status bit for the I2C_TRANS_COMPLETE_INT interrupt.
 */
#define I2C_TRANS_COMPLETE_INT_ST    (BIT(7))
#define I2C_TRANS_COMPLETE_INT_ST_M  (I2C_TRANS_COMPLETE_INT_ST_V << I2C_TRANS_COMPLETE_INT_ST_S)
#define I2C_TRANS_COMPLETE_INT_ST_V  0x00000001U
#define I2C_TRANS_COMPLETE_INT_ST_S  7
/** I2C_TIME_OUT_INT_ST : RO; bitpos: [8]; default: 0;
 *  The masked interrupt status bit for the I2C_TIME_OUT_INT interrupt.
 */
#define I2C_TIME_OUT_INT_ST    (BIT(8))
#define I2C_TIME_OUT_INT_ST_M  (I2C_TIME_OUT_INT_ST_V << I2C_TIME_OUT_INT_ST_S)
#define I2C_TIME_OUT_INT_ST_V  0x00000001U
#define I2C_TIME_OUT_INT_ST_S  8
/** I2C_TRANS_START_INT_ST : RO; bitpos: [9]; default: 0;
 *  The masked interrupt status bit for the I2C_TRANS_START_INT interrupt.
 */
#define I2C_TRANS_START_INT_ST    (BIT(9))
#define I2C_TRANS_START_INT_ST_M  (I2C_TRANS_START_INT_ST_V << I2C_TRANS_START_INT_ST_S)
#define I2C_TRANS_START_INT_ST_V  0x00000001U
#define I2C_TRANS_START_INT_ST_S  9
/** I2C_NACK_INT_ST : RO; bitpos: [10]; default: 0;
 *  The masked interrupt status bit for I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_NACK_INT_ST    (BIT(10))
#define I2C_NACK_INT_ST_M  (I2C_NACK_INT_ST_V << I2C_NACK_INT_ST_S)
#define I2C_NACK_INT_ST_V  0x00000001U
#define I2C_NACK_INT_ST_S  10
/** I2C_TXFIFO_OVF_INT_ST : RO; bitpos: [11]; default: 0;
 *  The masked interrupt status bit for I2C_TXFIFO_OVF_INT interrupt.
 */
#define I2C_TXFIFO_OVF_INT_ST    (BIT(11))
#define I2C_TXFIFO_OVF_INT_ST_M  (I2C_TXFIFO_OVF_INT_ST_V << I2C_TXFIFO_OVF_INT_ST_S)
#define I2C_TXFIFO_OVF_INT_ST_V  0x00000001U
#define I2C_TXFIFO_OVF_INT_ST_S  11
/** I2C_RXFIFO_UDF_INT_ST : RO; bitpos: [12]; default: 0;
 *  The masked interrupt status bit for I2C_RXFIFO_UDF_INT  interrupt.
 */
#define I2C_RXFIFO_UDF_INT_ST    (BIT(12))
#define I2C_RXFIFO_UDF_INT_ST_M  (I2C_RXFIFO_UDF_INT_ST_V << I2C_RXFIFO_UDF_INT_ST_S)
#define I2C_RXFIFO_UDF_INT_ST_V  0x00000001U
#define I2C_RXFIFO_UDF_INT_ST_S  12
/** I2C_SCL_ST_TO_INT_ST : RO; bitpos: [13]; default: 0;
 *  The masked interrupt status bit for I2C_SCL_ST_TO_INT interrupt.
 */
#define I2C_SCL_ST_TO_INT_ST    (BIT(13))
#define I2C_SCL_ST_TO_INT_ST_M  (I2C_SCL_ST_TO_INT_ST_V << I2C_SCL_ST_TO_INT_ST_S)
#define I2C_SCL_ST_TO_INT_ST_V  0x00000001U
#define I2C_SCL_ST_TO_INT_ST_S  13
/** I2C_SCL_MAIN_ST_TO_INT_ST : RO; bitpos: [14]; default: 0;
 *  The masked interrupt status bit for I2C_SCL_MAIN_ST_TO_INT interrupt.
 */
#define I2C_SCL_MAIN_ST_TO_INT_ST    (BIT(14))
#define I2C_SCL_MAIN_ST_TO_INT_ST_M  (I2C_SCL_MAIN_ST_TO_INT_ST_V << I2C_SCL_MAIN_ST_TO_INT_ST_S)
#define I2C_SCL_MAIN_ST_TO_INT_ST_V  0x00000001U
#define I2C_SCL_MAIN_ST_TO_INT_ST_S  14
/** I2C_DET_START_INT_ST : RO; bitpos: [15]; default: 0;
 *  The masked interrupt status bit for I2C_DET_START_INT interrupt.
 */
#define I2C_DET_START_INT_ST    (BIT(15))
#define I2C_DET_START_INT_ST_M  (I2C_DET_START_INT_ST_V << I2C_DET_START_INT_ST_S)
#define I2C_DET_START_INT_ST_V  0x00000001U
#define I2C_DET_START_INT_ST_S  15
/** I2C_SLAVE_STRETCH_INT_ST : RO; bitpos: [16]; default: 0;
 *  The masked interrupt status bit for I2C_SLAVE_STRETCH_INT interrupt.
 */
#define I2C_SLAVE_STRETCH_INT_ST    (BIT(16))
#define I2C_SLAVE_STRETCH_INT_ST_M  (I2C_SLAVE_STRETCH_INT_ST_V << I2C_SLAVE_STRETCH_INT_ST_S)
#define I2C_SLAVE_STRETCH_INT_ST_V  0x00000001U
#define I2C_SLAVE_STRETCH_INT_ST_S  16
/** I2C_GENERAL_CALL_INT_ST : RO; bitpos: [17]; default: 0;
 *  The masked interrupt status bit for I2C_GENARAL_CALL_INT interrupt.
 */
#define I2C_GENERAL_CALL_INT_ST    (BIT(17))
#define I2C_GENERAL_CALL_INT_ST_M  (I2C_GENERAL_CALL_INT_ST_V << I2C_GENERAL_CALL_INT_ST_S)
#define I2C_GENERAL_CALL_INT_ST_V  0x00000001U
#define I2C_GENERAL_CALL_INT_ST_S  17
/** I2C_SLAVE_ADDR_UNMATCH_INT_ST : RO; bitpos: [18]; default: 0;
 *  The masked interrupt status bit for I2C_SLAVE_ADDR_UNMATCH_INT interrupt.
 */
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST    (BIT(18))
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST_M  (I2C_SLAVE_ADDR_UNMATCH_INT_ST_V << I2C_SLAVE_ADDR_UNMATCH_INT_ST_S)
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST_V  0x00000001U
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST_S  18

/** I2C_SDA_HOLD_REG register
 *  Configures the hold time after a negative SCL edge.
 */
#define I2C_SDA_HOLD_REG(i) (REG_I2C_BASE(i) + 0x30)
/** I2C_SDA_HOLD_TIME : R/W; bitpos: [8:0]; default: 0;
 *  This register is used to configure the time to hold the data after the negative
 *  edge of SCL, in I2C module clock cycles.
 */
#define I2C_SDA_HOLD_TIME    0x000001FFU
#define I2C_SDA_HOLD_TIME_M  (I2C_SDA_HOLD_TIME_V << I2C_SDA_HOLD_TIME_S)
#define I2C_SDA_HOLD_TIME_V  0x000001FFU
#define I2C_SDA_HOLD_TIME_S  0

/** I2C_SDA_SAMPLE_REG register
 *  Configures the sample time after a positive SCL edge.
 */
#define I2C_SDA_SAMPLE_REG(i) (REG_I2C_BASE(i) + 0x34)
/** I2C_SDA_SAMPLE_TIME : R/W; bitpos: [8:0]; default: 0;
 *  This register is used to configure for how long SDA is sampled, in I2C module clock
 *  cycles.
 */
#define I2C_SDA_SAMPLE_TIME    0x000001FFU
#define I2C_SDA_SAMPLE_TIME_M  (I2C_SDA_SAMPLE_TIME_V << I2C_SDA_SAMPLE_TIME_S)
#define I2C_SDA_SAMPLE_TIME_V  0x000001FFU
#define I2C_SDA_SAMPLE_TIME_S  0

/** I2C_SCL_HIGH_PERIOD_REG register
 *  Configures the high level width of SCL
 */
#define I2C_SCL_HIGH_PERIOD_REG(i) (REG_I2C_BASE(i) + 0x38)
/** I2C_SCL_HIGH_PERIOD : R/W; bitpos: [8:0]; default: 0;
 *  This register is used to configure for how long SCL remains high in master mode, in
 *  I2C module clock cycles.
 */
#define I2C_SCL_HIGH_PERIOD    0x000001FFU
#define I2C_SCL_HIGH_PERIOD_M  (I2C_SCL_HIGH_PERIOD_V << I2C_SCL_HIGH_PERIOD_S)
#define I2C_SCL_HIGH_PERIOD_V  0x000001FFU
#define I2C_SCL_HIGH_PERIOD_S  0
/** I2C_SCL_WAIT_HIGH_PERIOD : R/W; bitpos: [15:9]; default: 0;
 *  This register is used to configure for the SCL_FSM's waiting period for SCL high
 *  level in master mode, in I2C module clock cycles.
 */
#define I2C_SCL_WAIT_HIGH_PERIOD    0x0000007FU
#define I2C_SCL_WAIT_HIGH_PERIOD_M  (I2C_SCL_WAIT_HIGH_PERIOD_V << I2C_SCL_WAIT_HIGH_PERIOD_S)
#define I2C_SCL_WAIT_HIGH_PERIOD_V  0x0000007FU
#define I2C_SCL_WAIT_HIGH_PERIOD_S  9

/** I2C_SCL_START_HOLD_REG register
 *  Configures the delay between the SDA and SCL negative edge for a start condition
 */
#define I2C_SCL_START_HOLD_REG(i) (REG_I2C_BASE(i) + 0x40)
/** I2C_SCL_START_HOLD_TIME : R/W; bitpos: [8:0]; default: 8;
 *  This register is used to configure the time between the negative edge
 *  of SDA and the negative edge of SCL for a START condition, in I2C module clock
 *  cycles.
 */
#define I2C_SCL_START_HOLD_TIME    0x000001FFU
#define I2C_SCL_START_HOLD_TIME_M  (I2C_SCL_START_HOLD_TIME_V << I2C_SCL_START_HOLD_TIME_S)
#define I2C_SCL_START_HOLD_TIME_V  0x000001FFU
#define I2C_SCL_START_HOLD_TIME_S  0

/** I2C_SCL_RSTART_SETUP_REG register
 *  Configures the delay between the positive
 *  edge of SCL and the negative edge of SDA
 */
#define I2C_SCL_RSTART_SETUP_REG(i) (REG_I2C_BASE(i) + 0x44)
/** I2C_SCL_RSTART_SETUP_TIME : R/W; bitpos: [8:0]; default: 8;
 *  This register is used to configure the time between the positive
 *  edge of SCL and the negative edge of SDA for a RESTART condition, in I2C module
 *  clock cycles.
 */
#define I2C_SCL_RSTART_SETUP_TIME    0x000001FFU
#define I2C_SCL_RSTART_SETUP_TIME_M  (I2C_SCL_RSTART_SETUP_TIME_V << I2C_SCL_RSTART_SETUP_TIME_S)
#define I2C_SCL_RSTART_SETUP_TIME_V  0x000001FFU
#define I2C_SCL_RSTART_SETUP_TIME_S  0

/** I2C_SCL_STOP_HOLD_REG register
 *  Configures the delay after the SCL clock
 *  edge for a stop condition
 */
#define I2C_SCL_STOP_HOLD_REG(i) (REG_I2C_BASE(i) + 0x48)
/** I2C_SCL_STOP_HOLD_TIME : R/W; bitpos: [8:0]; default: 8;
 *  This register is used to configure the delay after the STOP condition,
 *  in I2C module clock cycles.
 */
#define I2C_SCL_STOP_HOLD_TIME    0x000001FFU
#define I2C_SCL_STOP_HOLD_TIME_M  (I2C_SCL_STOP_HOLD_TIME_V << I2C_SCL_STOP_HOLD_TIME_S)
#define I2C_SCL_STOP_HOLD_TIME_V  0x000001FFU
#define I2C_SCL_STOP_HOLD_TIME_S  0

/** I2C_SCL_STOP_SETUP_REG register
 *  Configures the delay between the SDA and
 *  SCL positive edge for a stop condition
 */
#define I2C_SCL_STOP_SETUP_REG(i) (REG_I2C_BASE(i) + 0x4c)
/** I2C_SCL_STOP_SETUP_TIME : R/W; bitpos: [8:0]; default: 8;
 *  This register is used to configure the time between the positive edge
 *  of SCL and the positive edge of SDA, in I2C module clock cycles.
 */
#define I2C_SCL_STOP_SETUP_TIME    0x000001FFU
#define I2C_SCL_STOP_SETUP_TIME_M  (I2C_SCL_STOP_SETUP_TIME_V << I2C_SCL_STOP_SETUP_TIME_S)
#define I2C_SCL_STOP_SETUP_TIME_V  0x000001FFU
#define I2C_SCL_STOP_SETUP_TIME_S  0

/** I2C_FILTER_CFG_REG register
 *  SCL and SDA filter configuration register
 */
#define I2C_FILTER_CFG_REG(i) (REG_I2C_BASE(i) + 0x50)
/** I2C_SCL_FILTER_THRES : R/W; bitpos: [3:0]; default: 0;
 *  When a pulse on the SCL input has smaller width than this register value
 *  in I2C module clock cycles, the I2C controller will ignore that pulse.
 */
#define I2C_SCL_FILTER_THRES    0x0000000FU
#define I2C_SCL_FILTER_THRES_M  (I2C_SCL_FILTER_THRES_V << I2C_SCL_FILTER_THRES_S)
#define I2C_SCL_FILTER_THRES_V  0x0000000FU
#define I2C_SCL_FILTER_THRES_S  0
/** I2C_SDA_FILTER_THRES : R/W; bitpos: [7:4]; default: 0;
 *  When a pulse on the SDA input has smaller width than this register value
 *  in I2C module clock cycles, the I2C controller will ignore that pulse.
 */
#define I2C_SDA_FILTER_THRES    0x0000000FU
#define I2C_SDA_FILTER_THRES_M  (I2C_SDA_FILTER_THRES_V << I2C_SDA_FILTER_THRES_S)
#define I2C_SDA_FILTER_THRES_V  0x0000000FU
#define I2C_SDA_FILTER_THRES_S  4
/** I2C_SCL_FILTER_EN : R/W; bitpos: [8]; default: 1;
 *  This is the filter enable bit for SCL.
 */
#define I2C_SCL_FILTER_EN    (BIT(8))
#define I2C_SCL_FILTER_EN_M  (I2C_SCL_FILTER_EN_V << I2C_SCL_FILTER_EN_S)
#define I2C_SCL_FILTER_EN_V  0x00000001U
#define I2C_SCL_FILTER_EN_S  8
/** I2C_SDA_FILTER_EN : R/W; bitpos: [9]; default: 1;
 *  This is the filter enable bit for SDA.
 */
#define I2C_SDA_FILTER_EN    (BIT(9))
#define I2C_SDA_FILTER_EN_M  (I2C_SDA_FILTER_EN_V << I2C_SDA_FILTER_EN_S)
#define I2C_SDA_FILTER_EN_V  0x00000001U
#define I2C_SDA_FILTER_EN_S  9

/** I2C_CLK_CONF_REG register
 *  I2C CLK configuration register
 */
#define I2C_CLK_CONF_REG(i) (REG_I2C_BASE(i) + 0x54)
/** I2C_SCLK_DIV_NUM : R/W; bitpos: [7:0]; default: 0;
 *  the integral part of the fractional divisor for i2c module
 */
#define I2C_SCLK_DIV_NUM    0x000000FFU
#define I2C_SCLK_DIV_NUM_M  (I2C_SCLK_DIV_NUM_V << I2C_SCLK_DIV_NUM_S)
#define I2C_SCLK_DIV_NUM_V  0x000000FFU
#define I2C_SCLK_DIV_NUM_S  0
/** I2C_SCLK_DIV_A : R/W; bitpos: [13:8]; default: 0;
 *  the numerator of the fractional part of the fractional divisor for i2c module
 */
#define I2C_SCLK_DIV_A    0x0000003FU
#define I2C_SCLK_DIV_A_M  (I2C_SCLK_DIV_A_V << I2C_SCLK_DIV_A_S)
#define I2C_SCLK_DIV_A_V  0x0000003FU
#define I2C_SCLK_DIV_A_S  8
/** I2C_SCLK_DIV_B : R/W; bitpos: [19:14]; default: 0;
 *  the denominator of the fractional part of the fractional divisor for i2c module
 */
#define I2C_SCLK_DIV_B    0x0000003FU
#define I2C_SCLK_DIV_B_M  (I2C_SCLK_DIV_B_V << I2C_SCLK_DIV_B_S)
#define I2C_SCLK_DIV_B_V  0x0000003FU
#define I2C_SCLK_DIV_B_S  14
/** I2C_SCLK_SEL : R/W; bitpos: [20]; default: 0;
 *  The clock selection for i2c module:0-XTAL,1-CLK_8MHz.
 */
#define I2C_SCLK_SEL    (BIT(20))
#define I2C_SCLK_SEL_M  (I2C_SCLK_SEL_V << I2C_SCLK_SEL_S)
#define I2C_SCLK_SEL_V  0x00000001U
#define I2C_SCLK_SEL_S  20
/** I2C_SCLK_ACTIVE : R/W; bitpos: [21]; default: 1;
 *  The clock switch for i2c module
 */
#define I2C_SCLK_ACTIVE    (BIT(21))
#define I2C_SCLK_ACTIVE_M  (I2C_SCLK_ACTIVE_V << I2C_SCLK_ACTIVE_S)
#define I2C_SCLK_ACTIVE_V  0x00000001U
#define I2C_SCLK_ACTIVE_S  21

/** I2C_COMD0_REG register
 *  I2C command register 0
 */
#define I2C_COMD0_REG(i) (REG_I2C_BASE(i) + 0x58)
/** I2C_COMMAND0 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 0. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND0    0x00003FFFU
#define I2C_COMMAND0_M  (I2C_COMMAND0_V << I2C_COMMAND0_S)
#define I2C_COMMAND0_V  0x00003FFFU
#define I2C_COMMAND0_S  0
/** I2C_COMMAND0_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 0 is done in I2C Master mode, this bit changes to high
 *  level.
 */
#define I2C_COMMAND0_DONE    (BIT(31))
#define I2C_COMMAND0_DONE_M  (I2C_COMMAND0_DONE_V << I2C_COMMAND0_DONE_S)
#define I2C_COMMAND0_DONE_V  0x00000001U
#define I2C_COMMAND0_DONE_S  31

/** I2C_COMD1_REG register
 *  I2C command register 1
 */
#define I2C_COMD1_REG(i) (REG_I2C_BASE(i) + 0x5c)
/** I2C_COMMAND1 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 1. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND1    0x00003FFFU
#define I2C_COMMAND1_M  (I2C_COMMAND1_V << I2C_COMMAND1_S)
#define I2C_COMMAND1_V  0x00003FFFU
#define I2C_COMMAND1_S  0
/** I2C_COMMAND1_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 1 is done in I2C Master mode, this bit changes to high
 *  level.
 */
#define I2C_COMMAND1_DONE    (BIT(31))
#define I2C_COMMAND1_DONE_M  (I2C_COMMAND1_DONE_V << I2C_COMMAND1_DONE_S)
#define I2C_COMMAND1_DONE_V  0x00000001U
#define I2C_COMMAND1_DONE_S  31

/** I2C_COMD2_REG register
 *  I2C command register 2
 */
#define I2C_COMD2_REG(i) (REG_I2C_BASE(i) + 0x60)
/** I2C_COMMAND2 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 2. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND2    0x00003FFFU
#define I2C_COMMAND2_M  (I2C_COMMAND2_V << I2C_COMMAND2_S)
#define I2C_COMMAND2_V  0x00003FFFU
#define I2C_COMMAND2_S  0
/** I2C_COMMAND2_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 2 is done in I2C Master mode, this bit changes to high
 *  Level.
 */
#define I2C_COMMAND2_DONE    (BIT(31))
#define I2C_COMMAND2_DONE_M  (I2C_COMMAND2_DONE_V << I2C_COMMAND2_DONE_S)
#define I2C_COMMAND2_DONE_V  0x00000001U
#define I2C_COMMAND2_DONE_S  31

/** I2C_COMD3_REG register
 *  I2C command register 3
 */
#define I2C_COMD3_REG(i) (REG_I2C_BASE(i) + 0x64)
/** I2C_COMMAND3 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 3. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND3    0x00003FFFU
#define I2C_COMMAND3_M  (I2C_COMMAND3_V << I2C_COMMAND3_S)
#define I2C_COMMAND3_V  0x00003FFFU
#define I2C_COMMAND3_S  0
/** I2C_COMMAND3_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 3 is done in I2C Master mode, this bit changes to high
 *  level.
 */
#define I2C_COMMAND3_DONE    (BIT(31))
#define I2C_COMMAND3_DONE_M  (I2C_COMMAND3_DONE_V << I2C_COMMAND3_DONE_S)
#define I2C_COMMAND3_DONE_V  0x00000001U
#define I2C_COMMAND3_DONE_S  31

/** I2C_COMD4_REG register
 *  I2C command register 4
 */
#define I2C_COMD4_REG(i) (REG_I2C_BASE(i) + 0x68)
/** I2C_COMMAND4 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 4. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND4    0x00003FFFU
#define I2C_COMMAND4_M  (I2C_COMMAND4_V << I2C_COMMAND4_S)
#define I2C_COMMAND4_V  0x00003FFFU
#define I2C_COMMAND4_S  0
/** I2C_COMMAND4_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 4 is done in I2C Master mode, this bit changes to high
 *  level.
 */
#define I2C_COMMAND4_DONE    (BIT(31))
#define I2C_COMMAND4_DONE_M  (I2C_COMMAND4_DONE_V << I2C_COMMAND4_DONE_S)
#define I2C_COMMAND4_DONE_V  0x00000001U
#define I2C_COMMAND4_DONE_S  31

/** I2C_COMD5_REG register
 *  I2C command register 5
 */
#define I2C_COMD5_REG(i) (REG_I2C_BASE(i) + 0x6c)
/** I2C_COMMAND5 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 5. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND5    0x00003FFFU
#define I2C_COMMAND5_M  (I2C_COMMAND5_V << I2C_COMMAND5_S)
#define I2C_COMMAND5_V  0x00003FFFU
#define I2C_COMMAND5_S  0
/** I2C_COMMAND5_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 5 is done in I2C Master mode, this bit changes to high level.
 */
#define I2C_COMMAND5_DONE    (BIT(31))
#define I2C_COMMAND5_DONE_M  (I2C_COMMAND5_DONE_V << I2C_COMMAND5_DONE_S)
#define I2C_COMMAND5_DONE_V  0x00000001U
#define I2C_COMMAND5_DONE_S  31

/** I2C_COMD6_REG register
 *  I2C command register 6
 */
#define I2C_COMD6_REG(i) (REG_I2C_BASE(i) + 0x70)
/** I2C_COMMAND6 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 6. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND6    0x00003FFFU
#define I2C_COMMAND6_M  (I2C_COMMAND6_V << I2C_COMMAND6_S)
#define I2C_COMMAND6_V  0x00003FFFU
#define I2C_COMMAND6_S  0
/** I2C_COMMAND6_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 6 is done in I2C Master mode, this bit changes to high level.
 */
#define I2C_COMMAND6_DONE    (BIT(31))
#define I2C_COMMAND6_DONE_M  (I2C_COMMAND6_DONE_V << I2C_COMMAND6_DONE_S)
#define I2C_COMMAND6_DONE_V  0x00000001U
#define I2C_COMMAND6_DONE_S  31

/** I2C_COMD7_REG register
 *  I2C command register 7
 */
#define I2C_COMD7_REG(i) (REG_I2C_BASE(i) + 0x74)
/** I2C_COMMAND7 : R/W; bitpos: [13:0]; default: 0;
 *  This is the content of command 7. It consists of three parts:
 *  op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
 *  Byte_num represents the number of bytes that need to be sent or received.
 *  ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
 *  structure for more
 *  Information.
 */
#define I2C_COMMAND7    0x00003FFFU
#define I2C_COMMAND7_M  (I2C_COMMAND7_V << I2C_COMMAND7_S)
#define I2C_COMMAND7_V  0x00003FFFU
#define I2C_COMMAND7_S  0
/** I2C_COMMAND7_DONE : R/W/SS; bitpos: [31]; default: 0;
 *  When command 7 is done in I2C Master mode, this bit changes to high level.
 */
#define I2C_COMMAND7_DONE    (BIT(31))
#define I2C_COMMAND7_DONE_M  (I2C_COMMAND7_DONE_V << I2C_COMMAND7_DONE_S)
#define I2C_COMMAND7_DONE_V  0x00000001U
#define I2C_COMMAND7_DONE_S  31

/** I2C_SCL_ST_TIME_OUT_REG register
 *  SCL status time out register
 */
#define I2C_SCL_ST_TIME_OUT_REG(i) (REG_I2C_BASE(i) + 0x78)
/** I2C_SCL_ST_TO_I2C : R/W; bitpos: [4:0]; default: 16;
 *  The threshold value of SCL_FSM state unchanged period. It should be o more than 23
 */
#define I2C_SCL_ST_TO_I2C    0x0000001FU
#define I2C_SCL_ST_TO_I2C_M  (I2C_SCL_ST_TO_I2C_V << I2C_SCL_ST_TO_I2C_S)
#define I2C_SCL_ST_TO_I2C_V  0x0000001FU
#define I2C_SCL_ST_TO_I2C_S  0

/** I2C_SCL_MAIN_ST_TIME_OUT_REG register
 *  SCL main status time out register
 */
#define I2C_SCL_MAIN_ST_TIME_OUT_REG(i) (REG_I2C_BASE(i) + 0x7c)
/** I2C_SCL_MAIN_ST_TO_I2C : R/W; bitpos: [4:0]; default: 16;
 *  The threshold value of SCL_MAIN_FSM state unchanged period.nIt should be o more
 *  than 23
 */
#define I2C_SCL_MAIN_ST_TO_I2C    0x0000001FU
#define I2C_SCL_MAIN_ST_TO_I2C_M  (I2C_SCL_MAIN_ST_TO_I2C_V << I2C_SCL_MAIN_ST_TO_I2C_S)
#define I2C_SCL_MAIN_ST_TO_I2C_V  0x0000001FU
#define I2C_SCL_MAIN_ST_TO_I2C_S  0

/** I2C_SCL_SP_CONF_REG register
 *  Power configuration register
 */
#define I2C_SCL_SP_CONF_REG(i) (REG_I2C_BASE(i) + 0x80)
/** I2C_SCL_RST_SLV_EN : R/W/SC; bitpos: [0]; default: 0;
 *  When I2C master is IDLE, set this bit to send out SCL pulses. The number of pulses
 *  equals to reg_scl_rst_slv_num[4:0].
 */
#define I2C_SCL_RST_SLV_EN    (BIT(0))
#define I2C_SCL_RST_SLV_EN_M  (I2C_SCL_RST_SLV_EN_V << I2C_SCL_RST_SLV_EN_S)
#define I2C_SCL_RST_SLV_EN_V  0x00000001U
#define I2C_SCL_RST_SLV_EN_S  0
/** I2C_SCL_RST_SLV_NUM : R/W; bitpos: [5:1]; default: 0;
 *  Configure the pulses of SCL generated in I2C master mode. Valid when
 *  reg_scl_rst_slv_en is 1.
 */
#define I2C_SCL_RST_SLV_NUM    0x0000001FU
#define I2C_SCL_RST_SLV_NUM_M  (I2C_SCL_RST_SLV_NUM_V << I2C_SCL_RST_SLV_NUM_S)
#define I2C_SCL_RST_SLV_NUM_V  0x0000001FU
#define I2C_SCL_RST_SLV_NUM_S  1
/** I2C_SCL_PD_EN : R/W; bitpos: [6]; default: 0;
 *  The power down enable bit for the I2C output SCL line. 1: Power down. 0: Not power
 *  down. Set reg_scl_force_out and reg_scl_pd_en to 1 to stretch SCL low.
 */
#define I2C_SCL_PD_EN    (BIT(6))
#define I2C_SCL_PD_EN_M  (I2C_SCL_PD_EN_V << I2C_SCL_PD_EN_S)
#define I2C_SCL_PD_EN_V  0x00000001U
#define I2C_SCL_PD_EN_S  6
/** I2C_SDA_PD_EN : R/W; bitpos: [7]; default: 0;
 *  The power down enable bit for the I2C output SDA line. 1: Power down. 0: Not power
 *  down. Set reg_sda_force_out and reg_sda_pd_en to 1 to stretch SDA low.
 */
#define I2C_SDA_PD_EN    (BIT(7))
#define I2C_SDA_PD_EN_M  (I2C_SDA_PD_EN_V << I2C_SDA_PD_EN_S)
#define I2C_SDA_PD_EN_V  0x00000001U
#define I2C_SDA_PD_EN_S  7

/** I2C_SCL_STRETCH_CONF_REG register
 *  Set SCL stretch of I2C slave
 */
#define I2C_SCL_STRETCH_CONF_REG(i) (REG_I2C_BASE(i) + 0x84)
/** I2C_STRETCH_PROTECT_NUM : R/W; bitpos: [9:0]; default: 0;
 *  Configure the period of I2C slave stretching SCL line.
 */
#define I2C_STRETCH_PROTECT_NUM    0x000003FFU
#define I2C_STRETCH_PROTECT_NUM_M  (I2C_STRETCH_PROTECT_NUM_V << I2C_STRETCH_PROTECT_NUM_S)
#define I2C_STRETCH_PROTECT_NUM_V  0x000003FFU
#define I2C_STRETCH_PROTECT_NUM_S  0
/** I2C_SLAVE_SCL_STRETCH_EN : R/W; bitpos: [10]; default: 0;
 *  The enable bit for slave SCL stretch function. 1: Enable. 0: Disable. The SCL
 *  output line will be stretched low when reg_slave_scl_stretch_en is 1 and stretch
 *  event happens. The stretch cause can be seen in reg_stretch_cause.
 */
#define I2C_SLAVE_SCL_STRETCH_EN    (BIT(10))
#define I2C_SLAVE_SCL_STRETCH_EN_M  (I2C_SLAVE_SCL_STRETCH_EN_V << I2C_SLAVE_SCL_STRETCH_EN_S)
#define I2C_SLAVE_SCL_STRETCH_EN_V  0x00000001U
#define I2C_SLAVE_SCL_STRETCH_EN_S  10
/** I2C_SLAVE_SCL_STRETCH_CLR : WT; bitpos: [11]; default: 0;
 *  Set this bit to clear the I2C slave SCL stretch function.
 */
#define I2C_SLAVE_SCL_STRETCH_CLR    (BIT(11))
#define I2C_SLAVE_SCL_STRETCH_CLR_M  (I2C_SLAVE_SCL_STRETCH_CLR_V << I2C_SLAVE_SCL_STRETCH_CLR_S)
#define I2C_SLAVE_SCL_STRETCH_CLR_V  0x00000001U
#define I2C_SLAVE_SCL_STRETCH_CLR_S  11
/** I2C_SLAVE_BYTE_ACK_CTL_EN : R/W; bitpos: [12]; default: 0;
 *  The enable bit for slave to control ACK level function.
 */
#define I2C_SLAVE_BYTE_ACK_CTL_EN    (BIT(12))
#define I2C_SLAVE_BYTE_ACK_CTL_EN_M  (I2C_SLAVE_BYTE_ACK_CTL_EN_V << I2C_SLAVE_BYTE_ACK_CTL_EN_S)
#define I2C_SLAVE_BYTE_ACK_CTL_EN_V  0x00000001U
#define I2C_SLAVE_BYTE_ACK_CTL_EN_S  12
/** I2C_SLAVE_BYTE_ACK_LVL : R/W; bitpos: [13]; default: 0;
 *  Set the ACK level when slave controlling ACK level function enables.
 */
#define I2C_SLAVE_BYTE_ACK_LVL    (BIT(13))
#define I2C_SLAVE_BYTE_ACK_LVL_M  (I2C_SLAVE_BYTE_ACK_LVL_V << I2C_SLAVE_BYTE_ACK_LVL_S)
#define I2C_SLAVE_BYTE_ACK_LVL_V  0x00000001U
#define I2C_SLAVE_BYTE_ACK_LVL_S  13

/** I2C_DATE_REG register
 *  Version register
 */
#define I2C_DATE_REG(i) (REG_I2C_BASE(i) + 0xf8)
/** I2C_DATE : R/W; bitpos: [31:0]; default: 35656050;
 *  This is the the version register.
 */
#define I2C_DATE    0xFFFFFFFFU
#define I2C_DATE_M  (I2C_DATE_V << I2C_DATE_S)
#define I2C_DATE_V  0xFFFFFFFFU
#define I2C_DATE_S  0

/** I2C_TXFIFO_START_ADDR_REG register
 *  I2C TXFIFO base address register
 */
#define I2C_TXFIFO_START_ADDR_REG(i) (REG_I2C_BASE(i) + 0x100)
/** I2C_TXFIFO_START_ADDR : HRO; bitpos: [31:0]; default: 0;
 *  This is the I2C txfifo first address.
 */
#define I2C_TXFIFO_START_ADDR    0xFFFFFFFFU
#define I2C_TXFIFO_START_ADDR_M  (I2C_TXFIFO_START_ADDR_V << I2C_TXFIFO_START_ADDR_S)
#define I2C_TXFIFO_START_ADDR_V  0xFFFFFFFFU
#define I2C_TXFIFO_START_ADDR_S  0

/** I2C_RXFIFO_START_ADDR_REG register
 *  I2C RXFIFO base address register
 */
#define I2C_RXFIFO_START_ADDR_REG(i) (REG_I2C_BASE(i) + 0x180)
/** I2C_RXFIFO_START_ADDR : HRO; bitpos: [31:0]; default: 0;
 *  This is the I2C rxfifo first address.
 */
#define I2C_RXFIFO_START_ADDR    0xFFFFFFFFU
#define I2C_RXFIFO_START_ADDR_M  (I2C_RXFIFO_START_ADDR_V << I2C_RXFIFO_START_ADDR_S)
#define I2C_RXFIFO_START_ADDR_V  0xFFFFFFFFU
#define I2C_RXFIFO_START_ADDR_S  0

#ifdef __cplusplus
}
#endif