update h743eval with rhport=1 highspeed

hw/bsp/stm32h743eval/board.mk

@@ -8,11 +8,8 @@ CFLAGS += \
   -nostdlib -nostartfiles \
   -DSTM32H743xx \
   -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \
-  
-# Board specific for using usb ports
-CFLAGS += \
-	-DCFG_BOARD_DEVICE_RHPORT_NUM=1 \
-	-DCFG_BOARD_DEVICE_RHPORT_HIGHSPEED
+	-DBOARD_DEVICE_RHPORT_NUM=1 \
+	-DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
 
 # suppress warning caused by vendor mcu driver
 CFLAGS += -Wno-error=maybe-uninitialized

hw/bsp/stm32h743eval/stm32h743eval.c

@@ -32,11 +32,22 @@
 //--------------------------------------------------------------------+
 // Forward USB interrupt events to TinyUSB IRQ Handler
 //--------------------------------------------------------------------+
+
+// Despite being call USB2_OTG
+// OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port
 void OTG_FS_IRQHandler(void)
 {
   tud_int_handler(0);
 }
 
+// Despite being call USB2_OTG
+// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port
+void OTG_HS_IRQHandler(void)
+{
+  tud_int_handler(1);
+}
+
+
 //--------------------------------------------------------------------+
 // MACRO TYPEDEF CONSTANT ENUM
 //--------------------------------------------------------------------+
@@ -53,7 +64,7 @@ void OTG_FS_IRQHandler(void)
 // enable all LED, Button, Uart, USB clock
 static void all_rcc_clk_enable(void)
 {
-  __HAL_RCC_GPIOA_CLK_ENABLE();  // LED, USB D+, D-
+  __HAL_RCC_GPIOA_CLK_ENABLE();  // LED
   __HAL_RCC_GPIOC_CLK_ENABLE();  // Button
 //  __HAL_RCC_GPIOD_CLK_ENABLE();  // Uart tx, rx
 //  __HAL_RCC_USART3_CLK_ENABLE(); // Uart module
@@ -187,17 +198,13 @@ void board_init(void)
   GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
   HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
 
-#if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
-
-  // USB1 HS (ULPI Phy), internal FS PHY
-  // PB12 ID, PB13 VBUS, PB14 DM, PB15 DP
-
-#endif
-
-#if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
-  // USB2 FS Pin Init
+#if BOARD_DEVICE_RHPORT_NUM == 0
+  // Despite being call USB2_OTG
+  // OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port
   // PA9 VUSB, PA10 ID, PA11 DM, PA12 DP
 
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+
   /* Configure DM DP Pins */
   GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12;
   GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
@@ -228,6 +235,76 @@ void board_init(void)
   // Enable VBUS sense (B device) via pin PA9
   USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN;
 #endif
+
+#if BOARD_DEVICE_RHPORT_NUM == 1
+  // Despite being call USB2_OTG
+  // OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port
+  __GPIOA_CLK_ENABLE();
+  __GPIOB_CLK_ENABLE();
+  __GPIOC_CLK_ENABLE();
+  __GPIOH_CLK_ENABLE();
+  __GPIOI_CLK_ENABLE();
+
+  /* CLK */
+  GPIO_InitStruct.Pin = GPIO_PIN_5;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* D0 */
+  GPIO_InitStruct.Pin = GPIO_PIN_3;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* D1 D2 D3 D4 D5 D6 D7 */
+  GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_5 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS;
+  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /* STP */
+  GPIO_InitStruct.Pin = GPIO_PIN_0;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS;
+  HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+  /* NXT */
+  GPIO_InitStruct.Pin = GPIO_PIN_4;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS;
+  HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
+
+  /* DIR */
+  GPIO_InitStruct.Pin = GPIO_PIN_11;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS;
+  HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
+  __HAL_RCC_USB1_OTG_HS_ULPI_CLK_ENABLE();
+
+  /* Enable USB HS Clocks */
+  __HAL_RCC_USB1_OTG_HS_CLK_ENABLE();
+
+  // No VBUS sense
+  USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN;
+
+  // Force device mode
+  // USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD;
+  // USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD;
+
+  // B-peripheral session valid override enabl
+//  USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN;
+//  USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL;
+#endif // rhport = 1
+
 }
 
 //--------------------------------------------------------------------+

src/tusb_option.h

@@ -138,10 +138,6 @@
   #define CFG_TUSB_RHPORT0_MODE OPT_MODE_NONE
 #endif
 
-//#ifndef CFG_TUSB_RHPORT1_MODE
-//  #define CFG_TUSB_RHPORT1_MODE OPT_MODE_NONE
-//#endif
-
 #if ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST  ) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST   << 8)) ) || \
     ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)) )
   #error "TinyUSB currently does not support same modes on more than 1 roothub port"

test/test/support/tusb_config.h

@@ -43,12 +43,7 @@
   #define CFG_TUSB_MCU  OPT_MCU_NRF5X
 #endif
 
-#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX
 #define CFG_TUSB_RHPORT0_MODE    (OPT_MODE_DEVICE | OPT_MODE_HIGH_SPEED)
-#else
-#define CFG_TUSB_RHPORT0_MODE    OPT_MODE_DEVICE
-#endif
-
 #define CFG_TUSB_OS              OPT_OS_NONE
 
 // CFG_TUSB_DEBUG is defined by compiler in DEBUG build