group stm32f1 board

hw/bsp/stm32f0/family.c

@@ -55,12 +55,13 @@ void board_init(void)
   // Enable UART Clock
   UART_CLK_EN();
 
+#if CFG_TUSB_OS  == OPT_OS_NONE
   // 1ms tick timer
   SysTick_Config(SystemCoreClock / 1000);
 
-#if CFG_TUSB_OS == OPT_OS_FREERTOS
+#elif CFG_TUSB_OS == OPT_OS_FREERTOS
   // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
-  NVIC_SetPriority(USB_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+  NVIC_SetPriority(USB_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
 #endif
 
   // LED

hw/bsp/stm32f1/boards/stm32f103bluepill/board.h

@@ -0,0 +1,92 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED
+#define LED_PORT              GPIOC
+#define LED_PIN               GPIO_PIN_13
+#define LED_STATE_ON          0
+
+// Button
+#define BUTTON_PORT           GPIOA
+#define BUTTON_PIN            GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE   1
+
+// UART
+//#define UART_DEV              USART1
+//#define UART_CLK_EN           __HAL_RCC_USART1_CLK_ENABLE
+//#define UART_GPIO_PORT        GPIOA
+//#define UART_GPIO_AF          GPIO_AF1_USART1
+//#define UART_TX_PIN           GPIO_PIN_9
+//#define UART_RX_PIN           GPIO_PIN_10
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32f1_clock_init(void)
+{
+  RCC_ClkInitTypeDef clkinitstruct = {0};
+  RCC_OscInitTypeDef oscinitstruct = {0};
+  RCC_PeriphCLKInitTypeDef rccperiphclkinit = {0};
+
+  /* Enable HSE Oscillator and activate PLL with HSE as source */
+  oscinitstruct.OscillatorType  = RCC_OSCILLATORTYPE_HSE;
+  oscinitstruct.HSEState        = RCC_HSE_ON;
+  oscinitstruct.HSEPredivValue  = RCC_HSE_PREDIV_DIV1;
+  oscinitstruct.PLL.PLLMUL      = RCC_PLL_MUL9;
+  oscinitstruct.PLL.PLLState    = RCC_PLL_ON;
+  oscinitstruct.PLL.PLLSource   = RCC_PLLSOURCE_HSE;
+  HAL_RCC_OscConfig(&oscinitstruct);
+
+  /* USB clock selection */
+  rccperiphclkinit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  rccperiphclkinit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5;
+  HAL_RCCEx_PeriphCLKConfig(&rccperiphclkinit);
+
+  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+  clkinitstruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+  clkinitstruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  clkinitstruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  clkinitstruct.APB1CLKDivider = RCC_HCLK_DIV2;
+  clkinitstruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  HAL_RCC_ClockConfig(&clkinitstruct, FLASH_LATENCY_2);
+}
+
+static inline void board_vbus_sense_init(void)
+{
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* BOARD_H_ */

hw/bsp/stm32f1/boards/stm32f103bluepill/board.mk

@@ -0,0 +1,11 @@
+CFLAGS += -DSTM32F103xB -DHSE_VALUE=8000000U
+
+# All source paths should be relative to the top level.
+LD_FILE = $(BOARD_PATH)/STM32F103XB_FLASH.ld
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f103xb.s
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f103c8
+
+# flash target ROM bootloader
+flash: flash-dfu-util

hw/bsp/stm32f103bluepill/stm32f103bluepill.c → hw/bsp/stm32f1/family.c

@@ -24,8 +24,9 @@
  * This file is part of the TinyUSB stack.
  */
 
-#include "../board.h"
 #include "stm32f1xx_hal.h"
+#include "bsp/board.h"
+#include "board.h"
 
 //--------------------------------------------------------------------+
 // Forward USB interrupt events to TinyUSB IRQ Handler
@@ -48,72 +49,29 @@ void USBWakeUp_IRQHandler(void)
 //--------------------------------------------------------------------+
 // MACRO TYPEDEF CONSTANT ENUM
 //--------------------------------------------------------------------+
-#define LED_PORT              GPIOC
-#define LED_PIN               GPIO_PIN_13
-#define LED_STATE_ON          0
-
-#define BUTTON_PORT           GPIOA
-#define BUTTON_PIN            GPIO_PIN_0
-#define BUTTON_STATE_ACTIVE   1
-
-
-/**
-  * @brief  System Clock Configuration
-  *         The system Clock is configured as follow :
-  *            System Clock source            = PLL (HSE)
-  *            SYSCLK(Hz)                     = 72000000
-  *            HCLK(Hz)                       = 72000000
-  *            AHB Prescaler                  = 1
-  *            APB1 Prescaler                 = 2
-  *            APB2 Prescaler                 = 1
-  *            HSE Frequency(Hz)              = 8000000
-  *            HSE PREDIV1                    = 1
-  *            PLLMUL                         = 9
-  *            Flash Latency(WS)              = 2
-  * @param  None
-  * @retval None
-  */
-void SystemClock_Config(void)
-{
-  RCC_ClkInitTypeDef clkinitstruct = {0};
-  RCC_OscInitTypeDef oscinitstruct = {0};
-  RCC_PeriphCLKInitTypeDef rccperiphclkinit = {0};
-
-  /* Enable HSE Oscillator and activate PLL with HSE as source */
-  oscinitstruct.OscillatorType  = RCC_OSCILLATORTYPE_HSE;
-  oscinitstruct.HSEState        = RCC_HSE_ON;
-  oscinitstruct.HSEPredivValue  = RCC_HSE_PREDIV_DIV1;
-  oscinitstruct.PLL.PLLMUL      = RCC_PLL_MUL9;
-  oscinitstruct.PLL.PLLState    = RCC_PLL_ON;
-  oscinitstruct.PLL.PLLSource   = RCC_PLLSOURCE_HSE;
-  HAL_RCC_OscConfig(&oscinitstruct);
-
-  /* USB clock selection */
-  rccperiphclkinit.PeriphClockSelection = RCC_PERIPHCLK_USB;
-  rccperiphclkinit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5;
-  HAL_RCCEx_PeriphCLKConfig(&rccperiphclkinit);
-
-  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
-  clkinitstruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
-  clkinitstruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
-  clkinitstruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  clkinitstruct.APB1CLKDivider = RCC_HCLK_DIV2;
-  clkinitstruct.APB2CLKDivider = RCC_HCLK_DIV1;
-  HAL_RCC_ClockConfig(&clkinitstruct, FLASH_LATENCY_2);
-}
 
 void board_init(void)
 {
-
-  SystemClock_Config();
+  board_stm32f1_clock_init();
   
-  #if CFG_TUSB_OS  == OPT_OS_NONE
+  // Enable All GPIOs clocks
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOD_CLK_ENABLE();
+
+#if CFG_TUSB_OS  == OPT_OS_NONE
   // 1ms tick timer
   SysTick_Config(SystemCoreClock / 1000);
-  #endif
+
+#elif CFG_TUSB_OS == OPT_OS_FREERTOS
+  // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
+  NVIC_SetPriority(USB_HP_CAN1_TX_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+  NVIC_SetPriority(USB_LP_CAN1_RX0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+  NVIC_SetPriority(USBWakeUp_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+#endif
   
   // LED
-  __HAL_RCC_GPIOC_CLK_ENABLE();
   GPIO_InitTypeDef  GPIO_InitStruct;
   GPIO_InitStruct.Pin = LED_PIN;
   GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
@@ -122,7 +80,6 @@ void board_init(void)
   HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
 
   // Button
-  __HAL_RCC_GPIOA_CLK_ENABLE();
   GPIO_InitStruct.Pin = BUTTON_PIN;
   GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
   GPIO_InitStruct.Pull = GPIO_PULLDOWN;
@@ -131,7 +88,6 @@ void board_init(void)
 
   // USB Pins
   // Configure USB DM and DP pins.
-  __HAL_RCC_GPIOA_CLK_ENABLE();
   GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
   GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
   GPIO_InitStruct.Pull = GPIO_NOPULL;

hw/bsp/stm32f103bluepill/board.mk → hw/bsp/stm32f1/family.mk

@@ -4,6 +4,8 @@ DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm
 ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
 ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
 
+include $(TOP)/$(BOARD_PATH)/board.mk
+
 CFLAGS += \
   -flto \
   -mthumb \
@@ -11,15 +13,12 @@ CFLAGS += \
   -mcpu=cortex-m3 \
   -mfloat-abi=soft \
   -nostdlib -nostartfiles \
-  -DSTM32F103xB \
   -DCFG_TUSB_MCU=OPT_MCU_STM32F1
 
 # mcu driver cause following warnings
 #CFLAGS += -Wno-error=unused-parameter
 
 # All source paths should be relative to the top level.
-LD_FILE = hw/bsp/$(BOARD)/STM32F103XB_FLASH.ld
-
 SRC_C += \
   src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \
   $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
@@ -29,14 +28,11 @@ SRC_C += \
   $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
   $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c
 
-SRC_S += \
-  $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f103xb.s
-
 INC += \
+	$(TOP)/$(BOARD_PATH) \
   $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
   $(TOP)/$(ST_CMSIS)/Include \
-  $(TOP)/$(ST_HAL_DRIVER)/Inc \
-  $(TOP)/hw/bsp/$(BOARD)
+  $(TOP)/$(ST_HAL_DRIVER)/Inc
 
 # For freeRTOS port source
 FREERTOS_PORT = ARM_CM3
@@ -45,5 +41,5 @@ FREERTOS_PORT = ARM_CM3
 JLINK_DEVICE = stm32f103c8
 
 # flash target ROM bootloader
-flash: $(BUILD)/$(PROJECT).bin
+flash-dfu-util: $(BUILD)/$(PROJECT).bin
 	dfu-util -R -a 0 --dfuse-address 0x08000000 -D $<