add itsybitsy nrf52840 board support

docs/boards.md

@@ -38,6 +38,7 @@ This code base already had supported for a handful of following boards (sorted a
 - [Adafruit CLUE](https://www.adafruit.com/product/4500)
 - [Adafruit Feather nRF52840 Express](https://www.adafruit.com/product/4062)
 - [Adafruit Feather nRF52840 Sense](https://www.adafruit.com/product/4516)
+- [Adafruit ItsyBitsy nRF52840 Express](https://www.adafruit.com/product/4481)
 - [Arduino Nano 33 BLE](https://store.arduino.cc/usa/nano-33-ble)
 - [Arduino Nano 33 BLE Sense](https://store.arduino.cc/usa/nano-33-ble-sense)
 - [Maker Diary nRF52840 MDK Dongle](https://wiki.makerdiary.com/nrf52840-mdk-usb-dongle)

hw/bsp/itsybitsy_nrf52840/board.mk

@@ -0,0 +1,64 @@
+CFLAGS += \
+  -flto \
+  -mthumb \
+  -mabi=aapcs \
+  -mcpu=cortex-m4 \
+  -mfloat-abi=hard \
+  -mfpu=fpv4-sp-d16 \
+  -DCFG_TUSB_MCU=OPT_MCU_NRF5X \
+  -DNRF52840_XXAA \
+  -DCONFIG_GPIO_AS_PINRESET
+
+# suppress warning caused by vendor mcu driver
+CFLAGS += -Wno-error=undef -Wno-error=unused-parameter -Wno-error=cast-align
+
+# due to tusb_hal_nrf_power_event
+GCCVERSION = $(firstword $(subst ., ,$(shell arm-none-eabi-gcc -dumpversion)))
+ifeq ($(shell expr $(GCCVERSION) \>= 8), 1)
+CFLAGS += -Wno-error=cast-function-type
+endif
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/$(BOARD)/nrf52840_s140_v6.ld
+
+LDFLAGS += -L$(TOP)/hw/mcu/nordic/nrfx/mdk
+
+SRC_C += \
+  hw/mcu/nordic/nrfx/drivers/src/nrfx_power.c \
+  hw/mcu/nordic/nrfx/drivers/src/nrfx_uarte.c \
+  hw/mcu/nordic/nrfx/mdk/system_nrf52840.c
+
+INC += \
+  $(TOP)/lib/CMSIS_4/CMSIS/Include \
+  $(TOP)/hw/mcu/nordic \
+  $(TOP)/hw/mcu/nordic/nrfx \
+  $(TOP)/hw/mcu/nordic/nrfx/mdk \
+  $(TOP)/hw/mcu/nordic/nrfx/hal \
+  $(TOP)/hw/mcu/nordic/nrfx/drivers/include \
+  $(TOP)/hw/mcu/nordic/nrfx/drivers/src \
+
+SRC_S += hw/mcu/nordic/nrfx/mdk/gcc_startup_nrf52840.S
+
+ASFLAGS += -D__HEAP_SIZE=0
+
+# For TinyUSB port source
+VENDOR = nordic
+CHIP_FAMILY = nrf5x
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM4F
+
+# For flash-jlink target
+JLINK_DEVICE = nRF52840_xxAA
+JLINK_IF = swd
+
+# For uf2 conversion
+UF2_FAMILY = 0xADA52840
+
+$(BUILD)/$(BOARD)-firmware.zip: $(BUILD)/$(BOARD)-firmware.hex
+	adafruit-nrfutil dfu genpkg --dev-type 0x0052 --sd-req 0xFFFE --application $^ $@
+	
+# flash using adafruit-nrfutil dfu
+flash: $(BUILD)/$(BOARD)-firmware.zip
+	@:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0)
+	adafruit-nrfutil --verbose dfu serial --package $^ -p $(SERIAL) -b 115200 --singlebank --touch 1200

hw/bsp/itsybitsy_nrf52840/itsybitsy_nrf52840.c

@@ -0,0 +1,225 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "bsp/board.h"
+
+#include "nrfx.h"
+#include "nrfx/hal/nrf_gpio.h"
+#include "nrfx/drivers/include/nrfx_power.h"
+#include "nrfx/drivers/include/nrfx_uarte.h"
+
+#ifdef SOFTDEVICE_PRESENT
+#include "nrf_sdm.h"
+#include "nrf_soc.h"
+#endif
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USBD_IRQHandler(void)
+{
+  tud_int_handler(0);
+}
+
+/*------------------------------------------------------------------*/
+/* MACRO TYPEDEF CONSTANT ENUM
+ *------------------------------------------------------------------*/
+#define _PINNUM(port, pin)    ((port)*32 + (pin))
+
+#define LED_PIN         _PINNUM(0, 6)
+#define LED_STATE_ON    1
+
+#define BUTTON_PIN      _PINNUM(0, 29)
+
+#define UART_RX_PIN     25
+#define UART_TX_PIN     24
+
+static nrfx_uarte_t _uart_id = NRFX_UARTE_INSTANCE(0);
+
+// tinyusb function that handles power event (detected, ready, removed)
+// We must call it within SD's SOC event handler, or set it as power event handler if SD is not enabled.
+extern void tusb_hal_nrf_power_event(uint32_t event);
+
+void board_init(void)
+{
+  // stop LF clock just in case we jump from application without reset
+  NRF_CLOCK->TASKS_LFCLKSTOP = 1UL;
+
+  // Config clock source: XTAL or RC in sdk_config.h
+  NRF_CLOCK->LFCLKSRC = (uint32_t)((CLOCK_LFCLKSRC_SRC_Xtal << CLOCK_LFCLKSRC_SRC_Pos) & CLOCK_LFCLKSRC_SRC_Msk);
+  NRF_CLOCK->TASKS_LFCLKSTART = 1UL;
+
+  // LED
+  nrf_gpio_cfg_output(LED_PIN);
+  board_led_write(false);
+
+  // Button
+  nrf_gpio_cfg_input(BUTTON_PIN, NRF_GPIO_PIN_PULLUP);
+
+  // 1ms tick timer
+  SysTick_Config(SystemCoreClock/1000);
+
+  // UART
+  nrfx_uarte_config_t uart_cfg =
+  {
+    .pseltxd   = UART_TX_PIN,
+    .pselrxd   = UART_RX_PIN,
+    .pselcts   = NRF_UARTE_PSEL_DISCONNECTED,
+    .pselrts   = NRF_UARTE_PSEL_DISCONNECTED,
+    .p_context = NULL,
+    .baudrate  = NRF_UARTE_BAUDRATE_115200, // CFG_BOARD_UART_BAUDRATE
+    .interrupt_priority = 7,
+    .hal_cfg = {
+      .hwfc      = NRF_UARTE_HWFC_DISABLED,
+      .parity    = NRF_UARTE_PARITY_EXCLUDED,
+    }
+  };
+
+  nrfx_uarte_init(&_uart_id, &uart_cfg, NULL); //uart_handler);
+
+  //------------- USB -------------//
+#if TUSB_OPT_DEVICE_ENABLED
+  // Priorities 0, 1, 4 (nRF52) are reserved for SoftDevice
+  // 2 is highest for application
+  NVIC_SetPriority(USBD_IRQn, 2);
+
+  // USB power may already be ready at this time -> no event generated
+  // We need to invoke the handler based on the status initially
+  uint32_t usb_reg;
+
+#ifdef SOFTDEVICE_PRESENT
+  uint8_t sd_en = false;
+  sd_softdevice_is_enabled(&sd_en);
+
+  if ( sd_en ) {
+    sd_power_usbdetected_enable(true);
+    sd_power_usbpwrrdy_enable(true);
+    sd_power_usbremoved_enable(true);
+
+    sd_power_usbregstatus_get(&usb_reg);
+  }else
+#endif
+  {
+    // Power module init
+    const nrfx_power_config_t pwr_cfg = { 0 };
+    nrfx_power_init(&pwr_cfg);
+
+    // Register tusb function as USB power handler
+    const nrfx_power_usbevt_config_t config = { .handler = (nrfx_power_usb_event_handler_t) tusb_hal_nrf_power_event };
+    nrfx_power_usbevt_init(&config);
+
+    nrfx_power_usbevt_enable();
+
+    usb_reg = NRF_POWER->USBREGSTATUS;
+  }
+
+  if ( usb_reg & POWER_USBREGSTATUS_VBUSDETECT_Msk ) tusb_hal_nrf_power_event(NRFX_POWER_USB_EVT_DETECTED);
+  if ( usb_reg & POWER_USBREGSTATUS_OUTPUTRDY_Msk  ) tusb_hal_nrf_power_event(NRFX_POWER_USB_EVT_READY);
+#endif
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+  nrf_gpio_pin_write(LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+  // button is active LOW
+  return (nrf_gpio_pin_read(BUTTON_PIN) ? 0 : 1);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+  (void) buf; (void) len;
+  return 0;
+//  return NRFX_SUCCESS == nrfx_uart_rx(&_uart_id, buf, (size_t) len) ? len : 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+  return (NRFX_SUCCESS == nrfx_uarte_tx(&_uart_id, (uint8_t const*) buf, (size_t) len)) ? len : 0;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+  system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+  return system_ticks;
+}
+#endif
+
+#ifdef SOFTDEVICE_PRESENT
+// process SOC event from SD
+uint32_t proc_soc(void)
+{
+  uint32_t soc_evt;
+  uint32_t err = sd_evt_get(&soc_evt);
+
+  if (NRF_SUCCESS == err)
+  {
+    /*------------- usb power event handler -------------*/
+    int32_t usbevt = (soc_evt == NRF_EVT_POWER_USB_DETECTED   ) ? NRFX_POWER_USB_EVT_DETECTED:
+                     (soc_evt == NRF_EVT_POWER_USB_POWER_READY) ? NRFX_POWER_USB_EVT_READY   :
+                     (soc_evt == NRF_EVT_POWER_USB_REMOVED    ) ? NRFX_POWER_USB_EVT_REMOVED : -1;
+
+    if ( usbevt >= 0) tusb_hal_nrf_power_event(usbevt);
+  }
+
+  return err;
+}
+
+uint32_t proc_ble(void)
+{
+  // do nothing with ble
+  return NRF_ERROR_NOT_FOUND;
+}
+
+void SD_EVT_IRQHandler(void)
+{
+  // process BLE and SOC until there is no more events
+  while( (NRF_ERROR_NOT_FOUND != proc_ble()) || (NRF_ERROR_NOT_FOUND != proc_soc()) )
+  {
+
+  }
+}
+
+void nrf_error_cb(uint32_t id, uint32_t pc, uint32_t info)
+{
+  (void) id;
+  (void) pc;
+  (void) info;
+}
+#endif

hw/bsp/itsybitsy_nrf52840/nrf52840_s140_v6.ld

@@ -0,0 +1,38 @@
+/* Linker script to configure memory regions. */
+
+SEARCH_DIR(.)
+GROUP(-lgcc -lc -lnosys)
+
+MEMORY
+{
+  FLASH (rx)     : ORIGIN = 0x26000, LENGTH = 0xED000 - 0x26000
+
+  /* SRAM required by S132 depend on
+   * - Attribute Table Size
+   * - Vendor UUID count
+   * - Max ATT MTU
+   * - Concurrent connection peripheral + central + secure links
+   * - Event Len, HVN queue, Write CMD queue
+   */ 
+  RAM (rwx) :  ORIGIN = 0x20003400, LENGTH = 0x20040000 - 0x20003400
+}
+
+SECTIONS
+{
+  . = ALIGN(4);
+  .svc_data :
+  {
+    PROVIDE(__start_svc_data = .);
+    KEEP(*(.svc_data))
+    PROVIDE(__stop_svc_data = .);
+  } > RAM
+  
+  .fs_data :
+  {
+    PROVIDE(__start_fs_data = .);
+    KEEP(*(.fs_data))
+    PROVIDE(__stop_fs_data = .);
+  } > RAM
+} INSERT AFTER .data;
+
+INCLUDE "nrf52_common.ld"