fix rt1010 rt1020 only has 1 usb controller, rt1050 rt1060 has 2

hw/bsp/mimxrt1020_evk/board.h

@@ -0,0 +1,34 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+// required since iMX RT10xx SDK include this file for board size
+#define BOARD_FLASH_SIZE (0x800000U)
+
+#endif /* BOARD_H_ */

hw/bsp/mimxrt1020_evk/board.mk

@@ -0,0 +1,55 @@
+CFLAGS += \
+  -mthumb \
+  -mabi=aapcs \
+  -mcpu=cortex-m7 \
+  -mfloat-abi=hard \
+  -mfpu=fpv5-d16 \
+  -D__ARMVFP__=0 -D__ARMFPV5__=0\
+  -DCPU_MIMXRT1021DAG5A \
+  -DXIP_EXTERNAL_FLASH=1 \
+  -DXIP_BOOT_HEADER_ENABLE=1 \
+  -DCFG_TUSB_MCU=OPT_MCU_MIMXRT10XX \
+  -DCFG_TUSB_MEM_SECTION='__attribute__((section(".data")))' \
+  -DCFG_TUSB_MEM_ALIGN='__attribute__((aligned(64)))'
+
+# mcu driver cause following warnings
+#CFLAGS += -Wno-error=float-equal -Wno-error=nested-externs
+CFLAGS += -Wno-error=unused-parameter
+
+MCU_DIR = hw/mcu/nxp/sdk/devices/MIMXRT1021
+
+# All source paths should be relative to the top level.
+LD_FILE = $(MCU_DIR)/gcc/MIMXRT1021xxxxx_flexspi_nor.ld
+
+SRC_C += \
+	$(MCU_DIR)/system_MIMXRT1021.c \
+	$(MCU_DIR)/xip/fsl_flexspi_nor_boot.c \
+	$(MCU_DIR)/project_template/clock_config.c \
+	$(MCU_DIR)/drivers/fsl_clock.c \
+	$(MCU_DIR)/drivers/fsl_gpio.c \
+	$(MCU_DIR)/drivers/fsl_common.c \
+	$(MCU_DIR)/drivers/fsl_lpuart.c
+
+INC += \
+	$(TOP)/hw/bsp/$(BOARD) \
+	$(TOP)/$(MCU_DIR)/../../CMSIS/Include \
+	$(TOP)/$(MCU_DIR) \
+	$(TOP)/$(MCU_DIR)/drivers \
+	$(TOP)/$(MCU_DIR)/project_template \
+
+SRC_S += $(MCU_DIR)/gcc/startup_MIMXRT1021.S
+
+# For TinyUSB port source
+VENDOR = nxp
+CHIP_FAMILY = transdimension
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM7
+
+# For flash-jlink target
+JLINK_DEVICE = CPU_MIMXRT1021DAG5A
+JLINK_IF = swd
+
+# flash by copying bin file to DAP Mass Storage
+flash: $(BUILD)/$(BOARD)-firmware.bin
+	cp $< /media/$(USER)/RT1020-EVK/

hw/bsp/mimxrt1020_evk/evkmimxrt1020_flexspi_nor_config.c

@@ -0,0 +1,49 @@
+/*
+ * Copyright 2018 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include "evkmimxrt1020_flexspi_nor_config.h"
+
+/* Component ID definition, used by tools. */
+#ifndef FSL_COMPONENT_ID
+#define FSL_COMPONENT_ID "platform.drivers.xip_board"
+#endif
+
+/*******************************************************************************
+ * Code
+ ******************************************************************************/
+#if defined(XIP_BOOT_HEADER_ENABLE) && (XIP_BOOT_HEADER_ENABLE == 1)
+#if defined(__CC_ARM) || defined(__ARMCC_VERSION) || defined(__GNUC__)
+__attribute__((section(".boot_hdr.conf")))
+#elif defined(__ICCARM__)
+#pragma location = ".boot_hdr.conf"
+#endif
+
+const flexspi_nor_config_t qspiflash_config = {
+    .memConfig =
+        {
+            .tag              = FLEXSPI_CFG_BLK_TAG,
+            .version          = FLEXSPI_CFG_BLK_VERSION,
+            .readSampleClkSrc = kFlexSPIReadSampleClk_LoopbackFromDqsPad,
+            .csHoldTime       = 3u,
+            .csSetupTime      = 3u,
+            // Enable DDR mode, Wordaddassable, Safe configuration, Differential clock
+            .sflashPadType = kSerialFlash_4Pads,
+            .serialClkFreq = kFlexSpiSerialClk_100MHz,
+            .sflashA1Size  = 8u * 1024u * 1024u,
+            .lookupTable =
+                {
+                    // Read LUTs
+                    FLEXSPI_LUT_SEQ(CMD_SDR, FLEXSPI_1PAD, 0xEB, RADDR_SDR, FLEXSPI_4PAD, 0x18),
+                    FLEXSPI_LUT_SEQ(DUMMY_SDR, FLEXSPI_4PAD, 0x06, READ_SDR, FLEXSPI_4PAD, 0x04),
+                },
+        },
+    .pageSize           = 256u,
+    .sectorSize         = 4u * 1024u,
+    .blockSize          = 256u * 1024u,
+    .isUniformBlockSize = false,
+};
+#endif /* XIP_BOOT_HEADER_ENABLE */

hw/bsp/mimxrt1020_evk/evkmimxrt1020_flexspi_nor_config.h

@@ -0,0 +1,268 @@
+/*
+ * Copyright 2018 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef __EVKMIMXRT1020_FLEXSPI_NOR_CONFIG__
+#define __EVKMIMXRT1020_FLEXSPI_NOR_CONFIG__
+
+#include <stdint.h>
+#include <stdbool.h>
+#include "fsl_common.h"
+
+/*! @name Driver version */
+/*@{*/
+/*! @brief XIP_BOARD driver version 2.0.0. */
+#define FSL_XIP_BOARD_DRIVER_VERSION (MAKE_VERSION(2, 0, 0))
+/*@}*/
+
+/* FLEXSPI memory config block related defintions */
+#define FLEXSPI_CFG_BLK_TAG (0x42464346UL)     // ascii "FCFB" Big Endian
+#define FLEXSPI_CFG_BLK_VERSION (0x56010400UL) // V1.4.0
+#define FLEXSPI_CFG_BLK_SIZE (512)
+
+/* FLEXSPI Feature related definitions */
+#define FLEXSPI_FEATURE_HAS_PARALLEL_MODE 1
+
+/* Lookup table related defintions */
+#define CMD_INDEX_READ 0
+#define CMD_INDEX_READSTATUS 1
+#define CMD_INDEX_WRITEENABLE 2
+#define CMD_INDEX_WRITE 4
+
+#define CMD_LUT_SEQ_IDX_READ 0
+#define CMD_LUT_SEQ_IDX_READSTATUS 1
+#define CMD_LUT_SEQ_IDX_WRITEENABLE 3
+#define CMD_LUT_SEQ_IDX_WRITE 9
+
+#define CMD_SDR 0x01
+#define CMD_DDR 0x21
+#define RADDR_SDR 0x02
+#define RADDR_DDR 0x22
+#define CADDR_SDR 0x03
+#define CADDR_DDR 0x23
+#define MODE1_SDR 0x04
+#define MODE1_DDR 0x24
+#define MODE2_SDR 0x05
+#define MODE2_DDR 0x25
+#define MODE4_SDR 0x06
+#define MODE4_DDR 0x26
+#define MODE8_SDR 0x07
+#define MODE8_DDR 0x27
+#define WRITE_SDR 0x08
+#define WRITE_DDR 0x28
+#define READ_SDR 0x09
+#define READ_DDR 0x29
+#define LEARN_SDR 0x0A
+#define LEARN_DDR 0x2A
+#define DATSZ_SDR 0x0B
+#define DATSZ_DDR 0x2B
+#define DUMMY_SDR 0x0C
+#define DUMMY_DDR 0x2C
+#define DUMMY_RWDS_SDR 0x0D
+#define DUMMY_RWDS_DDR 0x2D
+#define JMP_ON_CS 0x1F
+#define STOP 0
+
+#define FLEXSPI_1PAD 0
+#define FLEXSPI_2PAD 1
+#define FLEXSPI_4PAD 2
+#define FLEXSPI_8PAD 3
+
+#define FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1)                                                              \
+    (FLEXSPI_LUT_OPERAND0(op0) | FLEXSPI_LUT_NUM_PADS0(pad0) | FLEXSPI_LUT_OPCODE0(cmd0) | FLEXSPI_LUT_OPERAND1(op1) | \
+     FLEXSPI_LUT_NUM_PADS1(pad1) | FLEXSPI_LUT_OPCODE1(cmd1))
+
+//!@brief Definitions for FlexSPI Serial Clock Frequency
+typedef enum _FlexSpiSerialClockFreq
+{
+    kFlexSpiSerialClk_30MHz  = 1,
+    kFlexSpiSerialClk_50MHz  = 2,
+    kFlexSpiSerialClk_60MHz  = 3,
+    kFlexSpiSerialClk_75MHz  = 4,
+    kFlexSpiSerialClk_80MHz  = 5,
+    kFlexSpiSerialClk_100MHz = 6,
+    kFlexSpiSerialClk_133MHz = 7,
+    kFlexSpiSerialClk_166MHz = 8,
+    kFlexSpiSerialClk_200MHz = 9,
+} flexspi_serial_clk_freq_t;
+
+//!@brief FlexSPI clock configuration type
+enum
+{
+    kFlexSpiClk_SDR, //!< Clock configure for SDR mode
+    kFlexSpiClk_DDR, //!< Clock configurat for DDR mode
+};
+
+//!@brief FlexSPI Read Sample Clock Source definition
+typedef enum _FlashReadSampleClkSource
+{
+    kFlexSPIReadSampleClk_LoopbackInternally      = 0,
+    kFlexSPIReadSampleClk_LoopbackFromDqsPad      = 1,
+    kFlexSPIReadSampleClk_LoopbackFromSckPad      = 2,
+    kFlexSPIReadSampleClk_ExternalInputFromDqsPad = 3,
+} flexspi_read_sample_clk_t;
+
+//!@brief Misc feature bit definitions
+enum
+{
+    kFlexSpiMiscOffset_DiffClkEnable            = 0, //!< Bit for Differential clock enable
+    kFlexSpiMiscOffset_Ck2Enable                = 1, //!< Bit for CK2 enable
+    kFlexSpiMiscOffset_ParallelEnable           = 2, //!< Bit for Parallel mode enable
+    kFlexSpiMiscOffset_WordAddressableEnable    = 3, //!< Bit for Word Addressable enable
+    kFlexSpiMiscOffset_SafeConfigFreqEnable     = 4, //!< Bit for Safe Configuration Frequency enable
+    kFlexSpiMiscOffset_PadSettingOverrideEnable = 5, //!< Bit for Pad setting override enable
+    kFlexSpiMiscOffset_DdrModeEnable            = 6, //!< Bit for DDR clock confiuration indication.
+};
+
+//!@brief Flash Type Definition
+enum
+{
+    kFlexSpiDeviceType_SerialNOR    = 1,    //!< Flash devices are Serial NOR
+    kFlexSpiDeviceType_SerialNAND   = 2,    //!< Flash devices are Serial NAND
+    kFlexSpiDeviceType_SerialRAM    = 3,    //!< Flash devices are Serial RAM/HyperFLASH
+    kFlexSpiDeviceType_MCP_NOR_NAND = 0x12, //!< Flash device is MCP device, A1 is Serial NOR, A2 is Serial NAND
+    kFlexSpiDeviceType_MCP_NOR_RAM  = 0x13, //!< Flash deivce is MCP device, A1 is Serial NOR, A2 is Serial RAMs
+};
+
+//!@brief Flash Pad Definitions
+enum
+{
+    kSerialFlash_1Pad  = 1,
+    kSerialFlash_2Pads = 2,
+    kSerialFlash_4Pads = 4,
+    kSerialFlash_8Pads = 8,
+};
+
+//!@brief FlexSPI LUT Sequence structure
+typedef struct _lut_sequence
+{
+    uint8_t seqNum; //!< Sequence Number, valid number: 1-16
+    uint8_t seqId;  //!< Sequence Index, valid number: 0-15
+    uint16_t reserved;
+} flexspi_lut_seq_t;
+
+//!@brief Flash Configuration Command Type
+enum
+{
+    kDeviceConfigCmdType_Generic,    //!< Generic command, for example: configure dummy cycles, drive strength, etc
+    kDeviceConfigCmdType_QuadEnable, //!< Quad Enable command
+    kDeviceConfigCmdType_Spi2Xpi,    //!< Switch from SPI to DPI/QPI/OPI mode
+    kDeviceConfigCmdType_Xpi2Spi,    //!< Switch from DPI/QPI/OPI to SPI mode
+    kDeviceConfigCmdType_Spi2NoCmd,  //!< Switch to 0-4-4/0-8-8 mode
+    kDeviceConfigCmdType_Reset,      //!< Reset device command
+};
+
+//!@brief FlexSPI Memory Configuration Block
+typedef struct _FlexSPIConfig
+{
+    uint32_t tag;               //!< [0x000-0x003] Tag, fixed value 0x42464346UL
+    uint32_t version;           //!< [0x004-0x007] Version,[31:24] -'V', [23:16] - Major, [15:8] - Minor, [7:0] - bugfix
+    uint32_t reserved0;         //!< [0x008-0x00b] Reserved for future use
+    uint8_t readSampleClkSrc;   //!< [0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3
+    uint8_t csHoldTime;         //!< [0x00d-0x00d] CS hold time, default value: 3
+    uint8_t csSetupTime;        //!< [0x00e-0x00e] CS setup time, default value: 3
+    uint8_t columnAddressWidth; //!< [0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For
+    //! Serial NAND, need to refer to datasheet
+    uint8_t deviceModeCfgEnable; //!< [0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable
+    uint8_t deviceModeType; //!< [0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch,
+    //! Generic configuration, etc.
+    uint16_t waitTimeCfgCommands; //!< [0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for
+    //! DPI/QPI/OPI switch or reset command
+    flexspi_lut_seq_t deviceModeSeq; //!< [0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt
+    //! sequence number, [31:16] Reserved
+    uint32_t deviceModeArg;    //!< [0x018-0x01b] Argument/Parameter for device configuration
+    uint8_t configCmdEnable;   //!< [0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable
+    uint8_t configModeType[3]; //!< [0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe
+    flexspi_lut_seq_t
+        configCmdSeqs[3]; //!< [0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq
+    uint32_t reserved1;   //!< [0x02c-0x02f] Reserved for future use
+    uint32_t configCmdArgs[3];     //!< [0x030-0x03b] Arguments/Parameters for device Configuration commands
+    uint32_t reserved2;            //!< [0x03c-0x03f] Reserved for future use
+    uint32_t controllerMiscOption; //!< [0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more
+    //! details
+    uint8_t deviceType;    //!< [0x044-0x044] Device Type:  See Flash Type Definition for more details
+    uint8_t sflashPadType; //!< [0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal
+    uint8_t serialClkFreq; //!< [0x046-0x046] Serial Flash Frequencey, device specific definitions, See System Boot
+    //! Chapter for more details
+    uint8_t lutCustomSeqEnable; //!< [0x047-0x047] LUT customization Enable, it is required if the program/erase cannot
+    //! be done using 1 LUT sequence, currently, only applicable to HyperFLASH
+    uint32_t reserved3[2];           //!< [0x048-0x04f] Reserved for future use
+    uint32_t sflashA1Size;           //!< [0x050-0x053] Size of Flash connected to A1
+    uint32_t sflashA2Size;           //!< [0x054-0x057] Size of Flash connected to A2
+    uint32_t sflashB1Size;           //!< [0x058-0x05b] Size of Flash connected to B1
+    uint32_t sflashB2Size;           //!< [0x05c-0x05f] Size of Flash connected to B2
+    uint32_t csPadSettingOverride;   //!< [0x060-0x063] CS pad setting override value
+    uint32_t sclkPadSettingOverride; //!< [0x064-0x067] SCK pad setting override value
+    uint32_t dataPadSettingOverride; //!< [0x068-0x06b] data pad setting override value
+    uint32_t dqsPadSettingOverride;  //!< [0x06c-0x06f] DQS pad setting override value
+    uint32_t timeoutInMs;            //!< [0x070-0x073] Timeout threshold for read status command
+    uint32_t commandInterval;        //!< [0x074-0x077] CS deselect interval between two commands
+    uint16_t dataValidTime[2]; //!< [0x078-0x07b] CLK edge to data valid time for PORT A and PORT B, in terms of 0.1ns
+    uint16_t busyOffset;       //!< [0x07c-0x07d] Busy offset, valid value: 0-31
+    uint16_t busyBitPolarity;  //!< [0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 -
+    //! busy flag is 0 when flash device is busy
+    uint32_t lookupTable[64];           //!< [0x080-0x17f] Lookup table holds Flash command sequences
+    flexspi_lut_seq_t lutCustomSeq[12]; //!< [0x180-0x1af] Customizable LUT Sequences
+    uint32_t reserved4[4];              //!< [0x1b0-0x1bf] Reserved for future use
+} flexspi_mem_config_t;
+
+/*  */
+#define NOR_CMD_INDEX_READ CMD_INDEX_READ               //!< 0
+#define NOR_CMD_INDEX_READSTATUS CMD_INDEX_READSTATUS   //!< 1
+#define NOR_CMD_INDEX_WRITEENABLE CMD_INDEX_WRITEENABLE //!< 2
+#define NOR_CMD_INDEX_ERASESECTOR 3                     //!< 3
+#define NOR_CMD_INDEX_PAGEPROGRAM CMD_INDEX_WRITE       //!< 4
+#define NOR_CMD_INDEX_CHIPERASE 5                       //!< 5
+#define NOR_CMD_INDEX_DUMMY 6                           //!< 6
+#define NOR_CMD_INDEX_ERASEBLOCK 7                      //!< 7
+
+#define NOR_CMD_LUT_SEQ_IDX_READ CMD_LUT_SEQ_IDX_READ //!< 0  READ LUT sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READSTATUS \
+    CMD_LUT_SEQ_IDX_READSTATUS //!< 1  Read Status LUT sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI \
+    2 //!< 2  Read status DPI/QPI/OPI sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE \
+    CMD_LUT_SEQ_IDX_WRITEENABLE //!< 3  Write Enable sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE_XPI \
+    4 //!< 4  Write Enable DPI/QPI/OPI sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_ERASESECTOR 5 //!< 5  Erase Sector sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_ERASEBLOCK 8  //!< 8 Erase Block sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM \
+    CMD_LUT_SEQ_IDX_WRITE                //!< 9  Program sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_CHIPERASE 11 //!< 11 Chip Erase sequence in lookupTable id stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READ_SFDP 13 //!< 13 Read SFDP sequence in lookupTable id stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_RESTORE_NOCMD \
+    14 //!< 14 Restore 0-4-4/0-8-8 mode sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_EXIT_NOCMD \
+    15 //!< 15 Exit 0-4-4/0-8-8 mode sequence id in lookupTable stored in config blobk
+
+/*
+ *  Serial NOR configuration block
+ */
+typedef struct _flexspi_nor_config
+{
+    flexspi_mem_config_t memConfig; //!< Common memory configuration info via FlexSPI
+    uint32_t pageSize;              //!< Page size of Serial NOR
+    uint32_t sectorSize;            //!< Sector size of Serial NOR
+    uint8_t ipcmdSerialClkFreq;     //!< Clock frequency for IP command
+    uint8_t isUniformBlockSize;     //!< Sector/Block size is the same
+    uint8_t reserved0[2];           //!< Reserved for future use
+    uint8_t serialNorType;          //!< Serial NOR Flash type: 0/1/2/3
+    uint8_t needExitNoCmdMode;      //!< Need to exit NoCmd mode before other IP command
+    uint8_t halfClkForNonReadCmd;   //!< Half the Serial Clock for non-read command: true/false
+    uint8_t needRestoreNoCmdMode;   //!< Need to Restore NoCmd mode after IP commmand execution
+    uint32_t blockSize;             //!< Block size
+    uint32_t reserve2[11];          //!< Reserved for future use
+} flexspi_nor_config_t;
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+#endif /* __EVKMIMXRT1020_FLEXSPI_NOR_CONFIG__ */

hw/bsp/mimxrt1020_evk/mimxrt1020_evk.c

@@ -0,0 +1,169 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2018, hathach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+#include "fsl_device_registers.h"
+#include "fsl_gpio.h"
+#include "fsl_iomuxc.h"
+#include "fsl_clock.h"
+#include "fsl_lpuart.h"
+
+#include "clock_config.h"
+
+#define LED_PINMUX            IOMUXC_GPIO_AD_B0_05_GPIO1_IO05
+#define LED_PORT              GPIO1
+#define LED_PIN               5
+#define LED_STATE_ON          0
+
+// SW8 button
+#define BUTTON_PINMUX         IOMUXC_SNVS_WAKEUP_GPIO5_IO00
+#define BUTTON_PORT           GPIO5
+#define BUTTON_PIN            0
+#define BUTTON_STATE_ACTIVE   0
+
+// UART
+#define UART_PORT             LPUART1
+#define UART_RX_PINMUX        IOMUXC_GPIO_AD_B0_07_LPUART1_RX
+#define UART_TX_PINMUX        IOMUXC_GPIO_AD_B0_06_LPUART1_TX
+
+const uint8_t dcd_data[] = { 0x00 };
+
+void board_init(void)
+{
+  // Init clock
+  BOARD_BootClockRUN();
+  SystemCoreClockUpdate();
+
+  // Enable IOCON clock
+  CLOCK_EnableClock(kCLOCK_Iomuxc);
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+  // 1ms tick timer
+  SysTick_Config(SystemCoreClock / 1000);
+#elif CFG_TUSB_OS == OPT_OS_FREERTOS
+  // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
+//  NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+#endif
+
+  // LED
+  IOMUXC_SetPinMux( LED_PINMUX, 0U);
+  IOMUXC_SetPinConfig( LED_PINMUX, 0x10B0U);
+
+  gpio_pin_config_t led_config = { kGPIO_DigitalOutput, 0, kGPIO_NoIntmode };
+  GPIO_PinInit(LED_PORT, LED_PIN, &led_config);
+  board_led_write(true);
+
+  // Button
+  IOMUXC_SetPinMux( BUTTON_PINMUX, 0U);
+  gpio_pin_config_t button_config = { kGPIO_DigitalInput, 0, kGPIO_IntRisingEdge, };
+  GPIO_PinInit(BUTTON_PORT, BUTTON_PIN, &button_config);
+
+  // UART
+  IOMUXC_SetPinMux( UART_TX_PINMUX, 0U);
+  IOMUXC_SetPinMux( UART_RX_PINMUX, 0U);
+  IOMUXC_SetPinConfig( UART_TX_PINMUX, 0x10B0u);
+  IOMUXC_SetPinConfig( UART_RX_PINMUX, 0x10B0u);
+
+  lpuart_config_t uart_config;
+  LPUART_GetDefaultConfig(&uart_config);
+  uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE;
+  uart_config.enableTx = true;
+  uart_config.enableRx = true;
+  LPUART_Init(UART_PORT, &uart_config, (CLOCK_GetPllFreq(kCLOCK_PllUsb1) / 6U) / (CLOCK_GetDiv(kCLOCK_UartDiv) + 1U));
+
+  //------------- USB0 -------------//
+  // Clock
+  CLOCK_EnableUsbhs0PhyPllClock(kCLOCK_Usbphy480M, 480000000U);
+  CLOCK_EnableUsbhs0Clock(kCLOCK_Usb480M, 480000000U);
+
+  USBPHY_Type* usb_phy = USBPHY;
+
+  // Enable PHY support for Low speed device + LS via FS Hub
+  usb_phy->CTRL |= USBPHY_CTRL_SET_ENUTMILEVEL2_MASK | USBPHY_CTRL_SET_ENUTMILEVEL3_MASK;
+
+  // Enable all power for normal operation
+  usb_phy->PWD = 0;
+
+  // TX Timing
+  uint32_t phytx = usb_phy->TX;
+  phytx &= ~(USBPHY_TX_D_CAL_MASK | USBPHY_TX_TXCAL45DM_MASK | USBPHY_TX_TXCAL45DP_MASK);
+  phytx |= USBPHY_TX_D_CAL(0x0C) | USBPHY_TX_TXCAL45DP(0x06) | USBPHY_TX_TXCAL45DM(0x06);
+  usb_phy->TX = phytx;
+}
+
+//--------------------------------------------------------------------+
+// USB Interrupt Handler
+//--------------------------------------------------------------------+
+void USB_OTG1_IRQHandler(void)
+{
+  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
+    tuh_isr(0);
+  #endif
+
+  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+    tud_isr(0);
+  #endif
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+  GPIO_PinWrite(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+  // active low
+  return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+  LPUART_ReadBlocking(UART_PORT, buf, len);
+  return len;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+  LPUART_WriteBlocking(UART_PORT, (uint8_t*)buf, len);
+  return len;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler(void)
+{
+  system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+  return system_ticks;
+}
+#endif

src/portable/nxp/transdimension/dcd_transdimension.c

@@ -38,8 +38,17 @@
 
 #if CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX
   #include "fsl_device_registers.h"
+
+// RT1010 and RT1020 only has 1 USB controller
+#if FSL_FEATURE_SOC_USBHS_COUNT == 1
+  #define   DCD_REGS_BASE { (dcd_registers_t*) USB_BASE }
+  IRQn_Type DCD_IRQn[] =  { USB_OTG1_IRQn };
+
+// RT1050, RT1060 has 2 USB controllers
+#else
   #define   DCD_REGS_BASE { (dcd_registers_t*) USB1_BASE, (dcd_registers_t*) USB2_BASE }
   IRQn_Type DCD_IRQn[] =  { USB_OTG1_IRQn, USB_OTG2_IRQn };
+#endif
 
 #else
   #include "chip.h"