revert rhport config in nxp mcus

hw/bsp/ea4357/ea4357.c

@@ -149,7 +149,7 @@ void board_init(void)
    * status feedback from the distribution switch. GPIO54 is used for VBUS sensing. 15Kohm pull-down
    * resistors are always active
    */
-#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST)
+#if CFG_TUSB_RHPORT0_MODE
   Chip_USB0_Init();
 
 //  // Reset controller
@@ -185,7 +185,7 @@ void board_init(void)
    * of VBUS can be read via U31.
    * JP16 shall not be inserted.
    */
-#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8)
+#if CFG_TUSB_RHPORT1_MODE
   Chip_USB1_Init();
 
 //  // Reset controller
@@ -232,11 +232,11 @@ void USB0_IRQHandler(void)
 
 void USB1_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
     tuh_isr(1);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
     tud_int_handler(1);
   #endif
 }

hw/bsp/mcb1800/mcb1800.c

@@ -43,11 +43,11 @@ void USB0_IRQHandler(void)
 
 void USB1_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
     tuh_isr(1);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
     tud_int_handler(1);
   #endif
 }
@@ -163,7 +163,7 @@ void board_init(void)
   };
 
   // USB0
-#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST)
+#if CFG_TUSB_RHPORT0_MODE
   Chip_USB0_Init();
 
 //  // Reset controller
@@ -180,7 +180,7 @@ void board_init(void)
 #endif
 
   // USB1
-#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8)
+#if CFG_TUSB_RHPORT1_MODE
   Chip_USB1_Init();
 
 //  // Reset controller

hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c

@@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void)
 
 void USB_OTG2_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
     tuh_isr(1);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
     tud_int_handler(1);
   #endif
 }

hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c

@@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void)
 
 void USB_OTG2_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)
+  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
     tuh_isr(1);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
     tud_int_handler(1);
   #endif
 }

hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c

@@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void)
 
 void USB_OTG2_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
     tuh_isr(1);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
     tud_int_handler(1);
   #endif
 }

hw/bsp/ngx4330/ngx4330.c

@@ -161,7 +161,7 @@ void board_init(void)
    * status feedback from the distribution switch. GPIO54 is used for VBUS sensing. 15Kohm pull-down
    * resistors are always active
    */
-#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST)
+#if CFG_TUSB_RHPORT0_MODE
   Chip_USB0_Init();
 
 //  // Reset controller
@@ -197,7 +197,7 @@ void board_init(void)
    * of VBUS can be read via U31.
    * JP16 shall not be inserted.
    */
-#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8)
+#if CFG_TUSB_RHPORT1_MODE
   Chip_USB1_Init();
 
 //  // Reset controller
@@ -235,11 +235,11 @@ void USB0_IRQHandler(void)
 
 void USB1_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
     tuh_isr(1);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
     tud_int_handler(1);
   #endif
 }

hw/bsp/teensy_40/teensy40.c

@@ -135,11 +135,11 @@ void USB_OTG1_IRQHandler(void)
 
 void USB_OTG2_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
     tuh_isr(1);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
     tud_int_handler(1);
   #endif
 }