add lpc54628 but usb clock;phy doesn't seem to be right

hw/bsp/lpc54/boards/lpcxpresso54628/board.h

@@ -0,0 +1,59 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2021, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED
+#define LED_PORT              2
+#define LED_PIN               2
+#define LED_STATE_ON          0
+
+// WAKE button
+#define BUTTON_PORT           1
+#define BUTTON_PIN            1
+#define BUTTON_STATE_ACTIVE   0
+
+// UART
+#define UART_DEV              USART0
+#define UART_RX_PINMUX        0, 29, IOCON_PIO_DIG_FUNC1_EN
+#define UART_TX_PINMUX        0, 30, IOCON_PIO_DIG_FUNC1_EN
+
+// USB0 VBUS
+#define USB0_VBUS_PINMUX      0, 22, IOCON_PIO_DIG_FUNC7_EN
+
+// XTAL
+//#define XTAL0_CLK_HZ          (16 * 1000 * 1000U)
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif

hw/bsp/lpc54/boards/lpcxpresso54628/board.mk

@@ -0,0 +1,18 @@
+MCU_VARIANT = LPC54628
+MCU_CORE = LPC54628
+
+PORT ?= 0
+
+CFLAGS += -DCPU_LPC54628J512ET180
+CFLAGS += -Wno-error=double-promotion
+
+LD_FILE = $(MCU_DIR)/gcc/LPC54628J512_flash.ld
+
+LIBS += $(TOP)/$(MCU_DIR)/gcc/libpower_hardabi.a
+
+JLINK_DEVICE = LPC54628J512
+PYOCD_TARGET = LPC54628
+
+#flash: flash-pyocd
+
+flash: flash-jlink

hw/bsp/lpc54/family.c

@@ -63,6 +63,11 @@ void USB0_IRQHandler(void)
   tud_int_handler(0);
 }
 
+void USB1_IRQHandler(void)
+{
+  tud_int_handler(1);
+}
+
 /****************************************************************
 name: BOARD_BootClockFROHF96M
 outputs:
@@ -112,15 +117,15 @@ void board_init(void)
 #endif
 
   // Init all GPIO ports 54114 only has 2 ports.
-  GPIO_PortInit(GPIO, 0);
-  GPIO_PortInit(GPIO, 1);
-  //GPIO_PortInit(GPIO, 2);
+  GPIO_PortInit(GPIO, LED_PORT);
+  GPIO_PortInit(GPIO, BUTTON_PORT);
 
   // LED
   IOCON_PinMuxSet(IOCON, LED_PORT, LED_PIN, IOCON_PIO_DIG_FUNC0_EN);
   gpio_pin_config_t const led_config = { kGPIO_DigitalOutput, 0};
   GPIO_PinInit(GPIO, LED_PORT, LED_PIN, &led_config);
-  board_led_write(true);
+
+  board_led_write(0);
 
   // Button
   IOCON_PinMuxSet(IOCON, BUTTON_PORT, BUTTON_PIN, IOCON_PIO_DIG_FUNC0_EN | IOCON_PIO_MODE_PULLUP);
@@ -145,8 +150,41 @@ void board_init(void)
   // USB
   IOCON_PinMuxSet(IOCON, USB0_VBUS_PINMUX);
 
-  POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); /*Turn on USB Phy */
+#if defined(FSL_FEATURE_SOC_USBHSD_COUNT) && FSL_FEATURE_SOC_USBHSD_COUNT
+  // LPC546xx and LPC540xx has OTG 1 FS + 1 HS rhports
+
+  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+    // Port0 is Full Speed
+    POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); /*< Turn on USB Phy */
+    CLOCK_SetClkDiv(kCLOCK_DivUsb0Clk, 1, false);
+    CLOCK_AttachClk(kFRO_HF_to_USB0_CLK);
+
+    /*According to reference mannual, device mode setting has to be set by access usb host register */
+    CLOCK_EnableClock(kCLOCK_Usbhsl0); /* enable usb0 host clock */
+    USBFSH->PORTMODE |= USBFSH_PORTMODE_DEV_ENABLE_MASK;
+    CLOCK_DisableClock(kCLOCK_Usbhsl0); /* disable usb0 host clock */
+
+    CLOCK_EnableUsbfs0DeviceClock(kCLOCK_UsbSrcFro, CLOCK_GetFroHfFreq());
+  #endif
+
+  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
+    // Port1 is High Speed
+    POWER_DisablePD(kPDRUNCFG_PD_USB1_PHY);
+
+    /*According to reference mannual, device mode setting has to be set by access usb host register */
+    CLOCK_EnableClock(kCLOCK_Usbh1); /* enable usb1 host clock */
+    USBHSH->PORTMODE |= USBHSH_PORTMODE_DEV_ENABLE_MASK;
+    CLOCK_DisableClock(kCLOCK_Usbh1); /* enable usb1 host clock */
+
+    CLOCK_EnableUsbhs0DeviceClock(kCLOCK_UsbSrcUsbPll, 0U);
+  #endif
+
+#else
+  // LPC5411x series only has full speed device
+
+  POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); // Turn on USB Phy
   CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcFro, CLOCK_GetFreq(kCLOCK_FroHf)); /* enable USB IP clock */
+#endif
 }
 
 //--------------------------------------------------------------------+

hw/bsp/lpc54/family.mk

@@ -13,6 +13,16 @@ CFLAGS += \
   -DCFG_TUSB_MCU=OPT_MCU_LPC54XXX \
   -DCFG_TUSB_MEM_ALIGN='__attribute__((aligned(64)))' 
 
+ifeq ($(PORT), 1)
+  $(info "PORT1 High Speed")
+  CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
+
+  # LPC55 Highspeed Port1 can only write to USB_SRAM region
+  CFLAGS += -DCFG_TUSB_MEM_SECTION='__attribute__((section("m_usb_global")))'
+else
+  $(info "PORT0 Full Speed")
+endif
+
 # mcu driver cause following warnings
 CFLAGS += -Wno-error=unused-parameter