kurisaw e2aed47b6c [format][version]: synchronize bsp version configuration 2 tháng trước cách đây
..
applications b0c247fb59 [components/drivers][touch]删除多余的touch.h (#7090) 2 năm trước cách đây
board fe3c4d456e bsp中option env语句替换为新语句,并同步更新了source "$xxx"语句 1 năm trước cách đây
linking_scripts 4fcb87a8aa Support M2354 platform. 5 năm trước cách đây
.config e2aed47b6c [format][version]: synchronize bsp version configuration 2 tháng trước cách đây
Kconfig fe3c4d456e bsp中option env语句替换为新语句,并同步更新了source "$xxx"语句 1 năm trước cách đây
README.md 0da2fb5f9b Correct rvds.S including for armclang platform. 4 năm trước cách đây
SConscript 4fcb87a8aa Support M2354 platform. 5 năm trước cách đây
SConstruct c3125df8fa bsp: Separate nuvoton drivers (#10435) 6 tháng trước cách đây
config_lvgl e2aed47b6c [format][version]: synchronize bsp version configuration 2 tháng trước cách đây
project.ewp 5f9f522285 format: update all series of BSP configuration items (#10406) 6 tháng trước cách đây
project.eww fe1308976e version: version release preparation 7 tháng trước cách đây
project.uvoptx c3125df8fa bsp: Separate nuvoton drivers (#10435) 6 tháng trước cách đây
project.uvprojx c3125df8fa bsp: Separate nuvoton drivers (#10435) 6 tháng trước cách đây
rtconfig.h e2aed47b6c [format][version]: synchronize bsp version configuration 2 tháng trước cách đây
rtconfig.py c9878aacd2 [scons][iar] 将IAR的PLATFORM字段由iar调整为iccarm 3 năm trước cách đây
template.ewd 4fcb87a8aa Support M2354 platform. 5 năm trước cách đây
template.ewp 4fcb87a8aa Support M2354 platform. 5 năm trước cách đây
template.eww 4fcb87a8aa Support M2354 platform. 5 năm trước cách đây
template.uvprojx 4fcb87a8aa Support M2354 platform. 5 năm trước cách đây

README.md

NuMaker-M2354

1. Introduction

The NuMaker-M2354 is an evaluation board for Nuvoton NuMicro M2354 microcontrollers. The NuMaker-M2354 consists of two parts, a M2354 target board and an on-board Nu-Link2-Me debugger and programmer. The NuMaker-M2354 is designed for secure evaluation, prototype development and validation with power consumption monitoring function.

NuMaker-M2354

1.1 MCU specification

| | Features | | -- | -- | | MCU | M2354KJFAE | | Operation frequency | 96MHz | | embedded Flash size | 1MB, Dual Bank | | SRAM size | 256kB | | Crypto engine | PRNG, AES, ECC, RSA, HMAC and SHA crypto accelerator |

1.2 Interface

| Interface | | -- | | Arduino UNO | | USB 1.1 OTG ports | | A microSD slot | | A segment LCD port |

1.3 On-board devices

| Device | Description | Driver supporting status | | -- | -- | -- | |Wi-Fi module| ESP8266-ESP12, AT firmware v1.7 | Supported | |Segment LCD module| | Supported |

2. Supported compiler

Support GCC, MDK5, IAR IDE/compilers. More information of these compiler version as following:

IDE/Compiler Tested version
MDK5 5.26.2
IAR 8.32
GCC GCC 6.3.1 20170620 (Need update env)

Notice: (1) Please install Nu-Link_Keil_Driver or Nu-Link_IAR_Driver for development.

3. Program firmware

Step 1:

At first, you need to configure ISW1 switch on the NuMaker-M2354 board. Set the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-M2354 board and your computer using the USB Micro cable. After that, window manager will show a ‘NuMicro MCU’ virtual disk. Finally, you will use this virtual disk to burn firmware.

NuLinkMe

NuMicro MCU

Step 2:

A simple firmware burning method is that you can drag and drop the binary image file to NuMicro MCU virtual disk or copy the binary file to NuMicro MCU disk to burn firmware.

CopyTo

4. Test

You can use Tera Term terminate emulator (or other software) to type commands of RTT. All parameters of serial communication are shown in below image. Here, you can find out the corresponding port number of Nuvoton Virtual Com Port in window device manager.

Serial settings

5. Purchase

6. Resources