Meco Man ddccef3a64 modify RT_ALIGN_SIZE as 8 by default 3 лет назад
..
applications 0d1c709fa5 Sync upstream (#6793) 3 лет назад
board bf8db63c78 Fix building issue of Nuvoton porting. (#6833) 3 лет назад
linking_scripts 4fcb87a8aa Support M2354 platform. 5 лет назад
.config ddccef3a64 modify RT_ALIGN_SIZE as 8 by default 3 лет назад
Kconfig 9bc68d26a4 format Kconfig and sconscript 3 лет назад
README.md 0da2fb5f9b Correct rvds.S including for armclang platform. 4 лет назад
SConscript 4fcb87a8aa Support M2354 platform. 5 лет назад
SConstruct 83b3aadaa3 [Scons][iar][iccarm] IAR统一使用iccarm作为判断条件而不是是用IDE的名字来进行判断 3 лет назад
config_lvgl ddccef3a64 modify RT_ALIGN_SIZE as 8 by default 3 лет назад
rtconfig.py c9878aacd2 [scons][iar] 将IAR的PLATFORM字段由iar调整为iccarm 3 лет назад
template.ewd 4fcb87a8aa Support M2354 platform. 5 лет назад
template.ewp 4fcb87a8aa Support M2354 platform. 5 лет назад
template.eww 4fcb87a8aa Support M2354 platform. 5 лет назад
template.uvprojx 4fcb87a8aa Support M2354 platform. 5 лет назад

README.md

NuMaker-M2354

1. Introduction

The NuMaker-M2354 is an evaluation board for Nuvoton NuMicro M2354 microcontrollers. The NuMaker-M2354 consists of two parts, a M2354 target board and an on-board Nu-Link2-Me debugger and programmer. The NuMaker-M2354 is designed for secure evaluation, prototype development and validation with power consumption monitoring function.

NuMaker-M2354

1.1 MCU specification

| | Features | | -- | -- | | MCU | M2354KJFAE | | Operation frequency | 96MHz | | embedded Flash size | 1MB, Dual Bank | | SRAM size | 256kB | | Crypto engine | PRNG, AES, ECC, RSA, HMAC and SHA crypto accelerator |

1.2 Interface

| Interface | | -- | | Arduino UNO | | USB 1.1 OTG ports | | A microSD slot | | A segment LCD port |

1.3 On-board devices

| Device | Description | Driver supporting status | | -- | -- | -- | |Wi-Fi module| ESP8266-ESP12, AT firmware v1.7 | Supported | |Segment LCD module| | Supported |

2. Supported compiler

Support GCC, MDK5, IAR IDE/compilers. More information of these compiler version as following:

IDE/Compiler Tested version
MDK5 5.26.2
IAR 8.32
GCC GCC 6.3.1 20170620 (Need update env)

Notice: (1) Please install Nu-Link_Keil_Driver or Nu-Link_IAR_Driver for development.

3. Program firmware

Step 1:

At first, you need to configure ISW1 switch on the NuMaker-M2354 board. Set the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-M2354 board and your computer using the USB Micro cable. After that, window manager will show a ‘NuMicro MCU’ virtual disk. Finally, you will use this virtual disk to burn firmware.

NuLinkMe

NuMicro MCU

Step 2:

A simple firmware burning method is that you can drag and drop the binary image file to NuMicro MCU virtual disk or copy the binary file to NuMicro MCU disk to burn firmware.

CopyTo

4. Test

You can use Tera Term terminate emulator (or other software) to type commands of RTT. All parameters of serial communication are shown in below image. Here, you can find out the corresponding port number of Nuvoton Virtual Com Port in window device manager.

Serial settings

5. Purchase

6. Resources